Fortin EVO-ONE Regular Installation Guide for Audi Q3

Addendum - Suggested Wiring Configuration

This document provides installation and programming instructions for the Fortin EVO-ONE module for the Audi Q3 (2019-2022) with Push-to-Start ignition.

Vehicle Compatibility and Functions

The EVO-ONE module supports the following functions for the Audi Q3 (2019-2022) Push-to-Start:

Firmware and Options

Firmware Version: 61.[12] VW MINIMUM

To add the firmware version and options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool (sold separately).

Bypass Options

Program bypass options as follows:

Mandatory Installation Requirements

HOOD PIN: The hood pin switch (included) must be installed if the vehicle can be remote started with the hood open. Set Function A11 to OFF.

SECURITY STICKER: Installation of safety elements is mandatory. The hood pin and sticker are essential security elements and must be installed.

Technician Warning

WARNING: This module must be installed by a qualified technician. Incorrect connections can cause permanent damage to the vehicle.

Remote Starter Options

Program Remote Starter Option

Parts Required (Not included)

• 1x Vehicle Key
• 1x 10Amp Fuse
• 2x Diode

Key Requirement

1 Key Required for the Installation.

Automatic Transmission Wiring Connection

This section details the wiring connections for automatic transmission vehicles.

EVO-ONE Module Connections:

• A1-A12: Main harness connections. Examples: A1 (Yellow) to (+)-Ignition, A8 (Dk.Blue) to (-)-Start/Stop, A11 (Black) to Hood Pin.
• E1-E6: Power and Ground connections. E3 (Red) to (+)-12V, E4 (Black) to (-)-Ground.
• C1-C5: CAN Bus connections (CAN LOW, CAN HIGH).
• D1-D6: Transponder/Key bypass connections. D3 (Yellow/Red) to (+)-Foot Brake.

Vehicle Connections:

• Push-to-Start Button: Connects to the EVO-ONE module via a 6-pin black connector.
• OBD-II Connector: Front view connection point.
• Driver Kick Panel: Connections via 17-pin blue and black connectors.
• Transponder Bypass Loop: Wrap 5 to 10 loops around the vehicle key or valet key and connect to the module.

Note: Cut the loop for automatic transmission mode.

Key Bypass Programming Procedure

Follow these steps to program the key bypass module:

1. Step 1: Press and hold the programming button. Insert the 6-Pin Main connector. The LEDs will alternate between BLUE, RED, YELLOW & BLUE/RED flashes.
2. Step 2: Release the programming button when the BLUE LED is ON. If the BLUE LED is not solid, disconnect the 6-Pin Main connector and return to Step 1.
3. Step 3: Insert the required remaining connectors.
4. Step 4: Do not press the brake pedal. Press the Push-to-Start button once to turn on the ignition. The BLUE LED will flash rapidly.
5. Step 5: Press the Push-to-Start button once to turn off the ignition. The BLUE LED will turn off. The module is now programmed.

Remote Starter Functionality

To use the remote starter:

• Ensure all doors are closed.
• Initiate remote start.
• Unlock the doors using either the OEM remote, the remote-starter remote, or the door handle.
• Enter the vehicle with the Intelligent SmartKey.
• The vehicle is now ready to be put into gear and driven.

Notices and Warnings

Updated Firmware and Installation Guides

Updated firmware and installation guides are posted on the Fortin website regularly. It is recommended to update the module to the latest firmware and download the latest installation guide(s) prior to installation.

Visit www.fortinbypass.com for the latest version.

General Warning

The information in this guide is provided on an "as is" basis with no warranty of accuracy. The installer is solely responsible for checking and verifying all circuits before connecting. Only a computer-safe logic probe or digital multimeter should be used. Fortin Electronic Systems assumes no liability for the accuracy or currency of the information supplied. Installation is the sole responsibility of the installer. Fortin Electronic Systems assumes no liability for any type of installation. Neither the manufacturer nor distributor is responsible for damages caused by this module, except for replacement due to manufacturing defects. This module must be installed by a qualified technician. This guide is for informational purposes only and may change without notice.

Technical Support

Tel: 514-255-HELP (4357) | 1-877-336-7797

Website: www.fortinbypass.com