Maytag Top Load Washer Dimension Guide
This guide provides essential dimensions and electrical requirements for Maytag Top Load Washers, including models MVW4505MW, MVW5035MW, MVW5430MW, 7MMVW5035MW, and 7MMVW5435MW. Please read the IMPORTANT SAFETY INSTRUCTIONS and INSTALLATION INSTRUCTIONS in your appliance's Owner's Manual before installation and operation.
Electrical Requirements
| Model | Capacity (US/CAN) |
|---|---|
| MVW4505MW | 4.5 cu ft DOE (US), 5.2 cu ft IEC (CAN) |
| MVW5035MW | 4.5 cu ft DOE (US), 5.2 cu ft IEC (CAN) |
| MVW5430MW | 4.8 cu ft DOE (US), 5.5 cu ft IEC (CAN) |
| 7MMVW5035MW | 4.5 cu ft DOE (US), 5.2 cu ft IEC (CAN) |
| 7MMVW5435MW | 4.7 cu ft DOE (US), 5.4 cu ft IEC (CAN) |
Minimum Circuit Amperage Rating: 15 A
Operating Voltage: 120 VAC only
Operating Frequency: 60 Hz
Product Dimensions
The following tables detail the product dimensions for the specified Maytag Top Load Washer models.
Front View Dimensions
| Label | Description | in (minimum) | mm (minimum) | in (maximum) | mm (maximum) |
|---|---|---|---|---|---|
| A | Height (with feet) | 43 1/4 | 1100 | 44 1/4 | 1122 |
| B | Width | 27 3/4 | 683 | - | - |
| C | Top of Lid Height (with feet) | 38 | 966 | 39 | 988 |
| D | Depth | 27 | 692 | - | - |
[Diagram showing front view of washer with labels A, B, C, D indicating dimensions]
Side and Rear View Dimensions
| Label | Description | in (minimum) | mm (minimum) | in (maximum) | mm (maximum) |
|---|---|---|---|---|---|
| E | Height with Lid Open | 55 3/4 | 1415 | 56 3/8 | 1432 |
| F | Height of Lid | 18 7/8 | 449 | - | - |
| G | Width of Lid | 23 1/4 | 593 | - | - |
| H | Water Inlet Valves Height | 37 7/8 | 962 | 39 1/2 | 1003 |
| I | Water Inlet Valves from Side | 4 1/2 | 116 | - | - |
| J | Power Cord from Side | 2 1/2 | 63 | - | - |
| K | Power Cord Height | 37 3/8 | 950 | 37 1/2 | 953 |
| L | Power Cord Length | 62 | 1530 | - | - |
| M | Drain Hose Outlet Height | 7 1/4 | 170 | 7 3/4 | 197 |
| Drain Hose Outlet from Side | 4 5/16 | 107 | - | - | |
| Drain Hose Length | 41 | 1040 | - | - | |
| Diameter of Drain Hose | 1 | 25 | - | - |
[Diagram showing side and rear view of washer with labels E, F, G, H, I, J, K, L, M indicating dimensions]
Recessed Area or Closet Installation
When installing the washer in a recessed area or closet, ensure adequate clearance for proper ventilation and operation. The diagram below illustrates recommended clearances.
[Diagram showing a washer installed in a recessed area or closet, with dimensions for clearance: 3" (76 mm) on sides and top, 20" (508 mm) front clearance, 5" (126 mm) clearance for water inlet valves, 1" (25 mm) clearance for power cord, and ventilation openings of 48 in² (310 cm²) and 24 in² (155 cm²) on the closet door.]
NOTE: All washers should have 20" (508 mm) clearance. The dimensions shown represent recommended clearances, except for closet door ventilation openings which are minimum required. This washer has been tested for installation with 0" (0 mm) clearance on the sides. Consider allowing more space for ease of installation and servicing, as well as for companion appliances and clearances for walls, doors, and floor moldings. Add an additional 1" (25 mm) space on all sides of the washer to reduce noise transfer. If a closet door or louvered door is installed, air openings at the top and bottom of the door are required.
