Maytag Top Load Washer Dimension Guide
This guide provides detailed planning dimensions and electrical requirements for various Maytag Top Load Washer models.
Product Models Covered
This document covers the following Maytag Top Load Washer models:
- MVW4505MW
- MVW5035MW
- MVW5430MW
- 7MMVW5035MW
- 7MMVW5435MW
Electrical Requirements
| Model | Capacity (DOE/IEC) |
|---|---|
| MVW4505MW | 4.5 cu ft DOE (US), 5.2 cu ft IEC (CAN) |
| MVW5035MW | 4.5 cu ft DOE (US), 5.2 cu ft IEC (CAN) |
| MVW5430MW | 4.8 cu ft DOE (US), 5.5 cu ft IEC (CAN) |
| 7MMVW5035MW | 4.5 cu ft DOE (US), 5.2 cu ft IEC (CAN) |
| 7MMVW5435MW | 4.7 cu ft DOE (US), 5.4 cu ft IEC (CAN) |
Minimum Circuit Amperage Rating: 15 A
Operating Voltage: 120 V AC only
Operating Frequency: 60 Hz
Product Dimensions
The following tables provide detailed product dimensions in both inches and millimeters.
Overall Dimensions
| Dimension | in (minimum) | mm (minimum) | in (maximum) | mm (maximum) |
|---|---|---|---|---|
| A: Height (with feet) | 43 1/4 | 1100 | 44 1/4 | 1122 |
| B: Width | 27 3/4 | 683 | - | - |
| C: Top of Lid Height (with feet) | 38 | 966 | 39 | 988 |
| D: Depth | 27 | 692 | - | - |
Detailed Dimensions
| Dimension | in (minimum) | mm (minimum) | in (maximum) | mm (maximum) |
|---|---|---|---|---|
| E: Height with Lid Open | 55 3/4 | 1415 | 56 3/8 | 1432 |
| F: Height of Lid | 18 7/8 | 449 | - | - |
| G: Width of Lid | 23 1/4 | 593 | - | - |
| H: Water Inlet Valves Height | 37 7/8 | 962 | 39 1/2 | 1003 |
| Water Inlet Valves from Side | 4 1/2 | 116 | - | - |
| J: Power Cord from Side | 2 1/2 | 63 | - | - |
| K: Power Cord Height | 37 3/8 | 950 | 37 1/2 | 953 |
| Power Cord Length | 62 | 1530 | - | - |
| L: Drain Hose Outlet Height | 7 1/4 | 170 | 7 3/4 | 197 |
| Drain Hose Outlet from Side | 4 5/16 | 107 | - | - |
| Drain Hose Length | 41 | 1040 | - | - |
| Diameter of Drain Hose | 1 | 25 | - | - |
Installation Spacing Recommendations
The following diagram illustrates recommended spacing for recessed area or closet installation. These dimensions allow for proper ventilation and access.
Key Spacing Requirements:
- Maximum depth for recessed area: 14" (356 mm)
- Clearance from front of washer: 5" (126 mm)
- Side clearances: 3" (76 mm)
- Ventilation openings for closet doors are minimum required.
- Closet door ventilation: 48 in² (310 cm²) and 24 in² (155 cm²) openings are required.
- Adding an extra 1" (25 mm) on all sides of the washer can help reduce noise transfer.
Note: Washer tested for 0" (0 mm) side clearance. Additional space may be beneficial for installation, servicing, and clearance with adjacent appliances, walls, doors, and floor moldings.
