Product Models
This guide provides dimension information for the following Maytag Top Load Washer models:
- MVW4505MW
- MVW5035MW
- MVW5430MW
- 7MMVW5035MW
- 7MMVW5435MW
Electrical Requirements
Model | Capacity (US) | Capacity (CAN) |
---|---|---|
MVW4505MW | 4.5 cu ft DOE | 5.2 cu ft IEC |
MVW5035MW | 4.5 cu ft DOE | 5.2 cu ft IEC |
MVW5430MW | 4.8 cu ft DOE | 5.5 cu ft IEC |
7MMVW5035MW | 4.5 cu ft DOE | 5.2 cu ft IEC |
7MMVW5435MW | 4.7 cu ft DOE | 5.4 cu ft IEC |
Minimum Circuit Amperage Rating: 15 A
Operating Voltage: 120 VAC only
Operating Frequency: 60 Hz
Product Dimensions (Front View)
The following diagram illustrates the front view dimensions:
Dimension | Model | Inches (minimum) | Millimeters (minimum) | Inches (maximum) | Millimeters (maximum) |
---|---|---|---|---|---|
A: Height (with feet) | All listed models | 43¼ | 1100 | 44¼ | 1122 |
B: Width | All listed models | 27¾ | 683 | - | - |
C: Top of Lid Height (with feet) | All listed models | 38 | 966 | 39 | 988 |
D: Depth | All listed models | 27 | 692 | - | - |
Product Dimensions (Side View)
The following diagram illustrates the side view dimensions:
Dimension | Model | Inches (minimum) | Millimeters (minimum) | Inches (maximum) | Millimeters (maximum) |
---|---|---|---|---|---|
E: Height with Lid Open | All listed models | 55¾ | 1415 | 56¾ | 1432 |
F: Height of Lid | All listed models | 18⅞ | 449 | - | - |
G: Width of Lid | All listed models | 23¼ | 593 | - | - |
H: Water Inlet Valves Height | All listed models | 37⅞ | 962 | 39½ | 1003 |
Water Inlet Valves from Side | All listed models | 4½ | 116 | - | - |
J: Power Cord from Side | All listed models | 2½ | 63 | - | - |
K: Power Cord Height | All listed models | 37⅜ | 950 | 37½ | 953 |
L: Power Cord Length | All listed models | 62 | 1530 | - | - |
M: Drain Hose Outlet Height | All listed models | 7¼ | 170 | 7¾ | 197 |
Drain Hose Outlet from Side | All listed models | 4⁵⁄₁₆ | 107 | - | - |
Drain Hose Length | All listed models | 41 | 1040 | - | - |
Diameter of Drain Hose | All listed models | 1 | 25 | - | - |
Recessed Area or Closet Installation
This section provides guidelines for installing the washer in a recessed area or closet.
Note: All washers should have 20" (508 mm) clearance. The dimensions shown represent recommended clearances, except for closet door ventilation openings, which are minimum requirements.
This washer has been tested for installation with 0" (0 mm) clearance on the sides. Consider allowing more space for ease of installation and servicing, as well as for companion appliances and clearances for walls, doors, and floor moldings. Add an additional 1" (25 mm) space on all sides of the washer to reduce noise transfer. If a closet door or louvered door is installed, top and bottom air openings in the door are required.