PETLIBRO Product User Manuals

PETLIBRO Cat Water Fountain (Model: PLWF002)

This document provides user instructions for the PETLIBRO Cat Water Fountain, a 71 fl oz / 2.1L ultra-quiet pet water fountain designed for cats. It features BPA-free construction, two flow modes, and a dispenser bowl with four large filters.

The PETLIBRO Cat Water Fountain includes the following components:

• 1) Spout
• 2) Water Outlet
• 3) Water Tray
• 4) Filter
• 5) Filter Tray
• 6) Water Pipe
• 7) Water pump with power cord
• 8) Foam Filter
• 9) Charger
• 10) Soft Plug
• 11) Cord Slot
• 12) Water Tank

Warning:

• Dispose of all packaging materials properly, keeping polybags away from children and pets to prevent suffocation.
• Do NOT allow children to play with or around the pet water fountain.
• Keep close supervision when the appliance is used near children to avoid injury.
• Do NOT use the fountain with pets unable to reach the water tray or with physical disabilities.
• Do NOT place foreign objects in the water tank.
• Do NOT disassemble the fountain except as instructed in this manual.
• Do NOT use the fountain for purposes other than its intended use.
• Only use attachments recommended or sold by the manufacturer.
• Do NOT operate if the unit is malfunctioning or damaged. Do not attempt self-repairs; contact customer service.
• Always disconnect the power supply when the appliance is not in use or before cleaning.
• The power adapter and wire plug must not be flooded during cleaning.
• This product is for indoor use only.
• This product is not allowed to run without water.
• Never pull the electrical power cord to remove the plug.
• If the plug gets wet, turn off the electricity at the wall outlet and do NOT attempt to unplug.
• Check the device after installation. Do NOT plug in if there is water on the contact points or plug.
• Position the power cord to avoid tripping hazards.
• Do not use the appliance in the bathroom.
• Change the filter every 2 weeks or when the flow rate noticeably reduces. For multiple cats, more frequent replacement may be needed.

Caution:

• Do NOT allow pets to chew on or swallow any parts. Consider a cord conduit for power cord protection.
• Use an extension cord with a proper rating if necessary.
• Do NOT install or store the fountain where temperatures are below 0°C / 40°F.
• Read and observe all important notices on the product and packaging.

1. Soak the filter in a clean bowl for 5 minutes, then rinse thoroughly with tap water. Ensure the filter is fully soaked before operation to prevent spillage. Do not soak the filter in the water tank to avoid surface dust.
2. Position the pump according to the bottom slot shape. Press the pump to secure suction cups. Place the cord in the slot. The pump must be fixed in the correct position.
3. Install the soft plug to prevent water leakage and secure the power cord. Align the cord slot when installing.
4. Install the silicone pipe on the pump. Add water to the tank, keeping the level between the Min and Max marks. The pump will fail if it runs dry.
5. Install the filter tray and place the filter on it. Press down firmly to ensure the pipe outlet is clear.
6. Install the water tray. The spout installation is optional based on pet preference.
7. Connect the power adapter.

• Replace the filter and foam every 2 weeks.
• Clean the pump and fountain every 2 weeks.
• Add water before starting the machine to extend pump life.

How to clean the pump:

1. Remove the pump cover and impeller cover. The foam filter is inside the pump cover and should be changed every 2 weeks.
2. Remove the impeller using the brush hook.
3. Clean these parts with a brush. The brush can also be used for nozzle cleaning, recommended every 2 weeks.

This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device. To maintain compliance with FCC RF Exposure guidelines, this equipment should be installed and operated with minimum distance of 20cm from your body.

• 1-year warranty
• Lifetime support

Official website: www.petlibro.com

PETLIBRO Automatic Dog Feeder (Model: PLAF001)

This document provides user instructions for the PETLIBRO Automatic Dog Feeder, a 6L WiFi-enabled pet food dispenser with customizable feeding schedules, suitable for large dogs. It features an interactive voice recorder and dispenses 1-4 meals of dry food.

The package includes:

• Automatic Pet Feeder (x1)
• Stainless Steel Bowl (x1)
• Bowl Holder (x1)
• Power Adapter (x1)
• Desiccant Bag (x1)
• User Guide Kit (x1)

Front View:

• 1) Desiccant Carrier
• 2) Lid
• 3) Lid Lock Button
• 4) Food Tank Buckle
• 5) Base
• 6) Food Outlet
• 7) Stainless Bowl & Bowl Holder
• 8) Control Panel
• 9) LCD Display
• 10) Food Tank

Bottom View:

• 11) Battery Compartment
• 12) Speaker
• 13) Power Socket

The display shows Battery Level, Time (24H format), Locked/Unlocked status, Meal count (1-4), and Portion setting (1-9).

• Recording Button: Press and hold for 3s to start recording (max 10s). Press once to save.
• Unlocked Button: Press and hold for 3s to unlock buttons and screen.
• Up Button: Increases value in unlocked mode. In locked mode, press and hold for 6-10s to reset time to 00:00.
• Down Button: Decreases value in unlocked mode.
• Setting Button: Cycles through time, meal, and portion settings.
• Manual Feeding Button: Dispenses one portion of food when unlocked.

Note: Buttons and screen lock automatically after 30 seconds of standby.

1. Take out the food bowl from the food tank.
2. Place the desiccant bag into the carrier under the lid.
   • To prevent mold, change the desiccant bag every 15 days.
   • Remove the desiccant bag before cleaning the lid.
3. Add dry pet food to the food tank.
   • Do NOT use canned, wet, or moist pet food.
   • Recommended kibble size: 2-10mm / 0.07-0.4in diameter.
4. Put the lid back on, ensuring it snaps into place.
5. Install the food bowl onto the feeder base notches. To move the feeder, press the bowl down to detach it. Handle gently to avoid spilling. Lift the feeder by the base.
6. Connect the power adapter to a power socket and the cable to the feeder. Install 3 alkaline D batteries (not included) in the battery compartment for backup. The LCD display will light up, indicating the feeder is on.

1. Set the Current Time: Unlock the device. Press the Set button to flash the hour digits, use Up/Down buttons to set the hour, press Set to save. Then flash the minute digits, use Up/Down buttons to set the minute, press Set to save.
2. Set the Number of Meals per Day: After setting the time, the 'meal' indicator will flash. Use Up/Down buttons to select 1-4 meals, press Set to save.
3. Set the Feeding Time & Portion of Meals: For the first meal, set the time using Up/Down buttons and press Set. Then set the portion using Up/Down buttons and press Set. Repeat for other meals (up to 4 meals supported).

Reference for portion setting:

Important Notes:

• It is normal to hear clicks before food is dispensed.
• One or two kibbles may remain in the chute after feeding; they may dispense when the machine is moved.
• Refer to pet food packaging for detailed feeding instructions.
• Double-check the current time after setting.

In locked mode, press and hold the Up button for 6-10 seconds. The display will flash twice, and the time will reset to 00:00.

1. Unlock the system. Press and hold the Recording button for 3 seconds until a beep. Release the button and start recording (max 10 seconds).
2. Press the Recording button again to save, or wait 10 seconds for an automatic save. Two beeps indicate completion. Repeat to change recording. Press the button once to check the recorded voice.

Notes:

• Default meal call playback is 2 times.
• To delete a recording: In unlocked state, press and hold the Recording button for 3 seconds until a beep, then immediately press the Recording button again. Two beeps confirm deletion.

Unlock the screen, then press the Feed button. The feeder dispenses one portion of food. The normal schedule and portion are not affected.

Regular cleaning is recommended for pet health. Washable parts include the lid, food tank, stainless bowl, and bowl holder.

To clean the lid, food tank, and food tray:

1. Disconnect power before cleaning.
2. Remove the lid and take out the desiccant bag from the carrier.
3. To remove the food tray, press down the stainless steel bowl with the holder.
4. To remove the food tank, press the buckles on both sides and lift upwards.
5. Rinse and air dry all parts thoroughly before reassembling.

This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. To maintain compliance with FCC RF Exposure guidelines, this equipment should be installed and operated with minimum distance of 20cm from your body.

• 1-year warranty
• Lifetime support