AECOJOY 6x6 Storage Shed Installation Guide

Introduction

This guide provides comprehensive instructions for assembling the AECOJOY 6x6 Storage Shed, model SS16300GR. The product is delivered in two packages; please ensure all packages are received before commencing installation.

Tools and Preparation

Tools Required (Not Included)

• Electric Screwdriver
• Manual Screwdriver
• Ladder

Package Included Tools

• Gloves (1 Pair)
• Spanner (x2)

Attention

❗ Please read these instructions carefully and follow them strictly during installation to avoid future problems due to installation errors.

Installation Notes

Verify all parts against the Parts Lists and check their appearance before installation. Contact customer service if any issues are found. Ensure colored panels face outwards and all holes align. Install panels in the specified order, matching lines and holes precisely for stability. Tighten all screws securely to prevent the product from falling apart. A protective film covers the product; it can be removed after installation for the final appearance, or left on for continued protection if undamaged. Place the shed on a flat, level ground to prevent leaning or collapse; uneven ground may affect door closure.

Safety Precautions

Installation is recommended for two adults to ensure ease and safety. Wear the included gloves to prevent hand cuts. When using power tools near water, use a Residual Current Device (RCD). Use electric drivers with care to avoid slipping and injury; beginners may prefer a manual screwdriver. Be cautious when installing the roof; use a stable ladder and ensure the product is on level ground.

Please keep this instruction for future reference.

Parts List

Parts List A

Parts List B

Overall Diagram Description

A diagram shows the overall layout of shed components, indicating front, rear, left, right, and top panels, as well as door components, providing a visual overview of the parts.

Part List Summary

Assembly Instructions

Step 1: Assemble the Shed Base Frame

Note: The larger hole on the frame parts should always be covered over the small hole.

Assemble the base frame using parts BS1, BS2, BS3, and T-F. Secure them using screws F1 and washers V2. The diagram shows a rectangular base frame being constructed.

Step 2: Assemble the Shed Side Panels

Note: The colored side of the panels should face outwards. The left and right panels should be installed under the back panel.

2a: Initial Side Panel Setup

Attach four WS7A panels to form a square base. Secure with screws F1 and washers V2. The diagram shows four WS7A panels forming a corner structure.

Note: Do not install screws in the indicated holes at this stage; they will be installed later (refer to Page 10).

2b: Adding Vertical Supports

Note: Two adults are recommended for this step.

Attach vertical support parts US1 and US3 to the side panels using screws F1 and washers V2. Connect with brackets C2. The diagrams illustrate adding uprights to the structure.

2c: Attaching More Side Panels

Attach two W7A panels to the structure. Secure with screws F1 and washers V2. The diagram shows adding more panels to complete the sides.

Note: Directly cover the excess parts of the left and right panels.

2d: Attaching the Rear Panel

Attach the W5A panel to the rear of the shed. Secure with screws F1 and washers V2. Ensure W7A panels are positioned under W5A as indicated.

2e: Attaching Front Panels

Attach the W3A panels and UA panels to the front of the shed. Secure with screws F1 and washers V2. The diagrams show the attachment of these front panels.

Step 3: Assemble the Shed Top Frame

Assemble the top frame components A1, A2, C3, M2, and F2. The diagrams show the assembly of the roof structure.

3a: Top Frame Brackets

Connect A1 and A2 parts using C3 brackets and screws F2.

3b: Main Top Frame

Attach M2 parts to the assembled frame using screws F2.

3c: Attaching Top Frame to Shed

Place the assembled top frame onto the shed body. Secure using V2 washers and F1 screws.

Step 4: Assemble the Shed Top Panels

Note: Please steady the ladder and ensure the product is placed on a flat ground.

4a: Attaching Roof Panels

Attach the roof panels G6-7M, G6-7L, and G6-7R to the top frame. Secure with screws F1 and washers V2. The diagrams illustrate the placement and fastening of the roof panels.

4b: Securing Roof Structure

Complete the roof structure by attaching GC, M7, M9, M11, F1, V2, and F4 parts. The diagrams show the final roof assembly and fastening points.

Step 5: Assemble the Doors

Note: When viewing from the front, the vertical rod covers the horizontal rod. The larger hole should always cover small ones.

5a: Left Door (DL) Assembly

Assemble the left door (DL) using parts DA, DLA, DGA, DDA, DBA, WD6A-L, F1, and F2. Follow steps 1-4. Final fixation should be done after all parts are aligned.

5b: Right Door (DR) Assembly

Assemble the right door (DR) using parts DA, DRA, DGA, DDA, DBA, WD6A-R, F1, and F2. Follow steps 1-4. Final fixation should be done after all parts are aligned.

5c: Attaching Door Hardware

Note: The Left or Right is seen from the outside. Attach DL and DR doors to the shed body. Use parts DH, DC, F3, GL, F1, and V2 for hinges and attachments. The diagrams show the door mounting process.

The large piece (UA) needs to be installed on the wall side.

Step 6: Final Touches

Cover exposed parts on the upper beam M2 with plastic protective covers. Use SL caps for exposed parts on M7 and M11.