AECOJOY 6 ft. W x 4 ft. D Storage Shed Installation Guide
This guide provides detailed instructions for the assembly of your AECOJOY 6 ft. W x 4 ft. D Metal Storage Shed (Model 16207GR). Please read all instructions carefully before beginning assembly.
Before You Begin
The product comes in two packages.
Tools Required (Not Included):
- Electric Screwdriver
- Manual Screwdriver (+)
- Ladder
Package Included Tools:
- Gloves (1 Pair)
- Spanner (x2)
ATTENTION: Please read this instruction carefully before installation and follow it strictly. Ensure that there are no problems later due to installation errors.
Installation Notes
- Check the quantity of all parts before installation against the Parts Lists.
- Ensure the product appearance is correct before installation. Contact AECOJOY directly if there are any issues.
- Make sure the colored panels face outwards and all holes match.
- Install panels in the order specified. All lines and holes must be accurately matched for stability.
- Tighten all screws to prevent the product from falling apart.
- A protective film is on the surface; tear it off after installation for the final presentation. If the film is not damaged during installation, it can remain to protect the product.
- Place the product on flat ground to prevent leaning and collapse. Uneven ground may prevent the door from closing properly.
Safety Precautions
- We recommend two adults for easier and safer installation.
- Wear gloves to prevent hand cuts during installation.
- Use caution when using power tools near water; use of a residual current device (RCD) is advised.
- Use electric drivers carefully to prevent screws from slipping and causing injury. Beginners are recommended to use a manual screwdriver.
- Be careful not to fall when installing the roof. Ensure the ladder is steady and the product is on flat ground.
KEEP THIS INSTRUCTION FOR FUTURE REFERENCE.
Parts Identification and Assembly
Package A_Part List:
| PART | NO. | QTY. | PART | NO. | QTY. |
| WD6A-L | 1 | W3A | 2 | ||
| WD6A-R | 1 | WS7A | 4 | ||
| W5A | 1 | PW7A-L | 2 | ||
| W7A | 2 | PW7A-R | 2 |
Package B_Part List:
| PART | NO. | QTY. | PART | NO. | QTY. |
| A1 | 2 | DBA | 4 | ||
| A2 | 2 | GC | 4 | ||
| BS1 | 1 | GE | 2 | ||
| BS2 | 1 | T-F | 4 | ||
| BF3 | 2 | F1 | 184 | ||
| US1 | 2 | F2 | 20 | ||
| UF1 | 2 | F3 | 32 | ||
| UA | 2 | (1) | V2 | 170 | |
| M7 | 4 | F4 | 4 | ||
| M8 | 2 | DC | 2 | ||
| M1 | 2 | C2 | 4 | ||
| C3 | 4 | DH | 4 | ||
| M6 | 1 | GL | 1 | ||
| DA | 2 | SL | 30 | ||
| DLA | 1 | M20 | 1 | ||
| DRA | 1 | M4 | 1 | ||
| DGA | 2 | ST | 1 | ||
| DDA | 2 |
Door Assembly (DL and DR):
DL (Left Door): Attach DA and DH using F1 screws and V2 washers. Ensure the larger hole on DA is covered over the small hole.
DR (Right Door): Attach DA and DH using F1 screws and V2 washers. Ensure the larger hole on DA is covered over the small hole. Note: The spring bolt should be in the same direction as the door lock.
Shed Base Frame Assembly:
Assemble BS1, BS2, and BF3 using T-F connectors and F1 screws and V2 washers as shown in the diagram.
Shed Side Panels Assembly:
Main Frame: Connect M6, M7, M8, GC, and GE parts using F1 screws and V2 washers. Ensure the colored side faces outward. The back panel (WS7A) should be on the outside of the left and right panels.
Side Panels: Attach WS7A panels to the base frame using F1 screws and V2 washers. Note: Do not install screws in certain locations until other plates are installed.
Shed Top Panels Assembly:
Top Frame: Assemble US1 and UF1 parts using C2 connectors, F1 screws, and V2 washers.
Roof Panels: Attach PW7A-L and PW7A-R panels to the top frame using F1 screws and V2 washers.
Final Assembly Steps:
Continue assembling the remaining panels (W7A, W5A) using the provided screws (F1) and washers (V2). Ensure correct alignment and secure all connections.
Note: The final fixation should be done after all parts are aligned.
Two Adults Are Required for this step.
Attach W7A panels to the structure using V2 washers and F1 screws. Also attach W5A panels using V2 washers and F1 screws. Ensure the back panel is on the outside of the left and right panels.
Shed Top Frame Assembly: Attach W3A and UA parts to the top corners of the shed structure using V2 washers, F1 screws, and F2 screws.
Roof Support Assembly: Connect A1, A2, C3, M1 parts using F2 screws and V2 washers to form the roof support structure.
