6*4 Storage Shed Installation Guide - SS16307GR
Important Information
Note: The product comes in two packages. Please install after receiving all packages. ⚠️
Tools Required (Not Included)
Tools: Electric Screwdriver, + Manual Screwdriver, Ladder
Package Included Tools: Gloves x 1 Pair, Screwdriver x 1
ATTENTION
Please read this instruction carefully before installation and follow it strictly during installation. Ensure that there are no problems later due to installation errors.
Installation Notes
- Please check the quantity of all parts before installation (refer to the Parts Lists) and the appearance of the products. Please make sure the product is correct before installation. If there is any problem, please contact us directly.
- Make sure the colored panels are facing outwards and all the holes match. The panels are textured; please install the panels in the order specified in the instructions. All lines and holes must be accurately matched to make the storage shed more stable. Please ensure that all screws are tightened to prevent the product from falling apart.
- There is a protective film on the surface to protect the product; please tear it off after installation for the final presentation. If you do not damage the film during installation, it can also remain on the product to protect it.
- Please place the product on a flat ground to prevent leaning and collapse. If the ground is uneven, the door may not be closed properly.
Safety Precautions
- We recommend two adults to complete the installation. Two adults installing together will make the process easier and safer.
- The gloves must be worn to prevent hand cuts during installation.
- Take care when using power tools near water; the use of a residual current device (RCD) is advised.
- Please use the electric driver carefully during screwing to prevent the screw from slipping and hurting your hand. (We recommend that beginners use a manual screwdriver for installation.)
- Be careful not to fall when installing the roof. Please steady the ladder and make sure the product is placed on a flat ground.
PLEASE KEEP THIS INSTRUCTION FOR FUTURE REFERENCE.
Part List A
| PART | NO. | QTY. | PART | NO. | QTY. |
|---|---|---|---|---|---|
| (Diagram of 2L) | 2L | 1 | (Diagram of 1411mm part) | 19 | 2 |
| (Diagram of 2R) | 2R | 1 | (Diagram of 1000mm part) | 20 | 4 |
| (Diagram of 4F) | 4F | 2 | (Diagram of 120mm part) | 23 | 1 |
| (Diagram of 4B) | 4B | 1 | (Diagram of W1) | W1 | 2 |
| (Diagram of 5) | 5 | 4 | (Diagram of W5) | W5 | 6 |
| (Diagram of 7) | 7 | 2 | (Diagram of W6) | W6 | 2 |
| (Diagram of 9) | 9 | 1 | (Diagram of W7) | W7 | 4 |
| (Diagram of 10F) | 10F | 1 | (Diagram of M1) | M1 | 1 |
| (Diagram of 10B) | 10B | 1 | (Diagram of M2) | M2 | 1 |
| (Diagram of 11L) | 11L | 2 | (Diagram of S4) | S4 | 228 |
| (Diagram of 11R) | 11R | 2 | (Diagram of S6) | S6 | 52 |
| (Diagram of 12) | 12 | 1 | (Diagram of S7) | S7 | 52 |
| (Diagram of 17L) | 17L | 1 | (Diagram of S8) | S8 | 12 |
| (Diagram of 17R) | 17R | 1 | (Diagram of S9) | S9 | 4 |
| (Diagram of 18) | 18 | 1 |
Part List B
| PART | NO. | QTY. | PART | NO. | QTY. |
|---|---|---|---|---|---|
| (Diagram of 1L) | 1L | 1 | (Diagram of 6R) | 6R | 1 |
| (Diagram of 1R) | 1R | 1 | (Diagram of 8L) | 8L | 1 |
| (Diagram of 3L) | 3L | 1 | (Diagram of 8R) | 8R | 1 |
| (Diagram of 3R) | 3R | 1 | (Diagram of 15) | 15 | 2 |
| (Diagram of 6L) | 6L | 1 | (Diagram of 21L) | 21L | 2 |
Part List B (Continued)
| PART | NO. | QTY. | PART | NO. | QTY. |
|---|---|---|---|---|---|
| (Diagram of 21R) | 21R | 2 | (Diagram of F) | F | 2 |
| (Diagram of 22) | 22 | 6 | (Diagram of I) | I | 1 |
| (Diagram of W12) | W12 | 2 | (Diagram of F1) | F1 | 8 |
| (Diagram of W15) | W15 | 4 | (Diagram of F2) | F2 | 2 |
| (Diagram of A) | A | 1 | (Diagram of F3) | F3 | 4 |
| (Diagram of B) | B | 1 | (Diagram of F4) | F4 | 4 |
| (Diagram of C) | C | 2 | (Diagram of F5) | F5 | 2 |
| (Diagram of D) | D | 1 | (Diagram of F7) | F7 | 212 |
| (Diagram of E) | E | 1 | (Diagram of F8) | F8 | 40 |
Storage Shed Assembly Instruction_SS16307
Shed top panels
| NO. | QTY. |
|---|---|
| 18 | 1 |
| 19 | 2 |
| 20 | 4 |
| F4 | 4 |
| F5 | 2 |
| W12 | 2 |
| W15 | 4 |
Shed top panels
| NO. | QTY. |
|---|---|
| 9 | 1 |
| 10F | 1 |
| 10B | 1 |
| 11L | 2 |
| 11R | 2 |
| 21L | 2 |
| 22R | 2 |
STEP 1
Parts: 1L (1), 1R (1), 4F (2), S4 (4)
Attach part 1L to part 1R using four S4 screws. Then attach two 4F parts to the assembly using S4 screws.
STEP 2
Parts: 15 (2), S4 (8)
Attach two part 15 pieces to the existing assembly using eight S4 screws.
STEP 3
Parts: 3R (1), 3L (1), 4B (1), S4 (4)
Attach part 3R to the assembly using S4 screws. Attach part 3L to the assembly using S4 screws. Attach part 4B to the assembly using S4 screws.
STEP 4
Parts: A (1), B (1), S4 (4), 1L (1), 2L (1), 1R (1), 2R (1)
Attach part A and part B to the corners of the base structure (formed by 1L, 1R, 2L, 2R) using S4 screws.
STEP 5
Parts: C (2), S4 (4), 3L (1), 3R (1), 2L (1), 2R (1)
Attach two C parts to the corners of the base structure using S4 screws.
STEP 6
Parts: 5 (4)
Insert four part 5 pieces into the designated slots on the base structure.
STEP 7
Parts: 6L (1), 6R (1), 12 (1), F3 (4), S4 (2)
Attach part 6L and 6R to the structure. Insert part 12. Attach part F3 to 6R and 6L using S4 screws.
STEP 8
Parts: 23 (1), S4 (2)
Attach part 23 to the assembly using two S4 screws.
STEP 9
Parts: 8L (1), 8R (1), I (1), S4 (2)
Attach part 8L and 8R to the assembly. Attach part I using two S4 screws.
STEP 10
Parts: D (1), E (1), F (2), S4 (6), 7 (2), 6L (1), 6R (1), 8L (1), 8R (1)
Attach parts D, E, and F to the frame using S4 screws. Connect parts 7, 6L, 6R, 8L, and 8R.
STEP 11
Assemble the roof structure by placing panels on top of the frame.
STEP 12
Parts: W1 (1), W5 (1), W7 (2), S6 (3), S7 (3), F7 (27), S4 (24)
Attach W1, W5, and W7 panels to the roof structure using S6 and S7 screws. Use F7 and S4 screws for further fastening.
STEP 13
Parts: W1 (1), W5 (1), W7 (2), S6 (3), S7 (3), F7 (27), S4 (24)
Continue attaching roof panels W1, W5, and W7 using S6, S7, F7, and S4 screws.
STEP 14
Parts: 17L (1), 17R (1), W6 (2), S6 (8), S7 (8), F7 (8)
Attach side panels 17L and 17R to the structure using W6, S6, S7, and F7 fasteners.
STEP 15
Parts: W6 (2), S4 (20), S6 (2), S7 (2), F7 (22)
Attach W6 panels to the structure using S4, S6, S7, and F7 screws.
STEP 16
Parts: W5 (4), F7 (34), S6 (4), S7 (4), S4 (38)
Attach W5 panels to the structure using F7, S6, S7, and S4 screws.
STEP 17
Parts: 11R (1), S7 (4), 21L (2), 10B (1), S6 (2), 21R (2), 11L (2), 10F (1)
Assemble roof components. Attach 11R and 11L panels using S7 and S6 screws. Attach 21L and 21R panels using S6 screws. Connect with 10B and 10F parts.
STEP 18
Parts: 9 (1), S4 (2)
Attach part 9 to the assembly using two S4 screws.
STEP 19
Parts: S4 (12)
Secure the roof structure to the walls using twelve S4 screws.
STEP 20
Parts: F7 (12), S4 (12), W12 (2)
Attach W12 panels to the roof ridge using F7 and S4 screws.
STEP 21
Parts: F7 (32), S4 (32), W12 (2), W15 (2)
Attach W12 and W15 panels to the roof using F7 and S4 screws.
STEP 22
Parts: 20 (8), S4 (8), F7 (4), 20 (4)
Attach parts 20 to the structure using S4 and F7 screws.
STEP 23
Parts: F7 (8), S4 (4), 19 (2), F4 (4), S8 (4)
Attach part 19 to the roof using F7 and S4 screws. Attach F4 and S8 parts to the corners of the roof.
STEP 24
Parts: F7 (6), S4 (6), F5 (2), 18 (1), 19 (1)
Attach part 18 and 19 to the roof using F7 and S4 screws. Attach F5 parts.
STEP 25
Parts: M1 (1), M2 (1), S7 (22), F1 (8), S6 (24), S7 (24), F7 (24)
Assemble door components. Attach M1 and M2 panels. Attach F1 to the door using S7 and S6 screws. Use F7 screws for further fastening. Make sure to install [F1] to the door.
STEP 26
Parts: S4 (6)
Attach M1 and M2 panels to the door frame using S4 screws.
STEP 27
Parts: F2 (2), S6 (8), S7 (8), M1 (1), M2 (1)
Attach M1 and M2 panels to the door frame using F2, S6, and S7 screws.
STEP 28
Parts: S8 (8)
Attach S8 screws to the door frame.
STEP 29
Parts: F8 (40), S9 (4)
Attach F8 screws to the roof. If the shed is installed on grass, the [S9] can be used to increase the stability of the shed.
