3x7.5 Storage Shed Installation Guide

Tools Required (Not Included)

• Electric Screwdriver
• Manual Screwdriver
• Ladder
• Gloves x 1 Pair
• Spanner x 1

Part List

Please check all parts against the list below before installation.

Main Components

Frame and Panel Parts

Installation Notes

Please read these instructions carefully before installation and follow them strictly. Ensure all parts are present and in good condition before starting. If any issues arise, contact the manufacturer directly. Ensure colored panels face outwards and all holes align for stability. Tighten all screws securely. A protective film is applied to panels; it can be removed after installation or left on for added protection. Install the shed on a flat, level surface to prevent leaning and ensure the door operates correctly.

Safety Precautions

It is recommended that two adults perform the installation for ease and safety. Wear gloves to prevent hand injuries. Exercise caution when using power tools, especially near water, and use a Residual Current Device (RCD) if necessary. Use electric drivers carefully to avoid slipping and injury; beginners may prefer manual screwdrivers. Be mindful of falling when installing the roof; use a stable ladder and ensure the product is on level ground.

Keep these instructions for future reference.

Assembly Instructions

Step 1: Assemble the Base Frame

This step involves assembling the base frame. Connect side rails (1L, 1R) to end rails (3L, 3R). Parts 2, 4B, and 5 are attached to the frame using screws (S4) and brackets (C).

Parts Used: 1L (1), 1R (1), 2 (2), 3L (1), 3R (1), 4B (2), 5 (4), C (4), S4 (implied).

Step 2: Attach Vertical Supports

Attach vertical support posts (5) to the base frame. Four posts (5) are secured using screws (S4).

Parts Used: 5 (4), S4 (implied).

Step 3: Connect Horizontal Supports

Connect horizontal support pieces (F, FF) between the vertical posts. Two F parts and two FF parts are used.

Parts Used: F (2), FF (2).

Step 4: Assemble Side Frame

Assemble the side frame structure. Connect vertical posts (8L, 8R) to horizontal pieces (6, 7, 10) using screws (S4).

Parts Used: 6 (2), 7 (2), 8L (1), 8R (1), 10 (1), S4 (implied).

Step 5: Assemble Other Side Frame

Assemble the other side frame structure. Connect vertical posts (6L, 6R) to horizontal pieces (10, FL, FR, I) using screws (S4).

Parts Used: 6L (1), 6R (1), 10 (1), FL (1), FR (1), I (1), S4 (implied).

Step 6: Attach Wall Panels (W5)

Attach the first set of wall panels (W5) to the assembled frame. Panels (W5) are secured with screws (S4, S6, S7) and brackets (F7).

Parts Used: W5 (2), S4 (14), S6 (1), S7 (1), F7 (15).

Step 7: Attach More Wall Panels (W5)

Attach the next set of wall panels (W5) to the frame. Panels (W5) are secured with screws (S4, S6, S7) and brackets (F7).

Parts Used: W5 (2), S4 (14), S6 (1), S7 (1), F7 (15).

Step 8: Attach Wall Panels (W7)

Attach wall panels (W7) to the frame. Panels (W7) are secured with screws (S4, S6, S7) and brackets (F7).

Parts Used: W7 (2), S4 (16), S6 (2), S7 (2), F7 (18).

Step 9: Attach Wall Panels (W5)

Attach the final set of wall panels (W5) to the frame. Panels (W5) are secured with screws (S4, S6, S7) and brackets (F7).

Parts Used: W5 (3), S4 (26), S6 (4), S7 (4), F7 (30).

Step 10: Attach Roof Supports (W1, W2, W3)

Attach roof support beams (W1, W2, W3) to the top of the shed frame. Secured with screws (S4, S6, S7) and brackets (F7).

Parts Used: W1 (1), W2 (1), W3 (1), S4 (10), S6 (2), S7 (2), F7 (12).

Step 11: Attach Roof Panels (17L, 17R)

Attach roof panels (17L, 17R) to the roof structure. Secured with screws (S4, S6, S7) and brackets (F7).

Parts Used: 17L (1), 17R (1), S4 (8), S6 (3), S7 (3), F7 (7).

Step 12: Attach Roof Panels (21L, 21R)

Attach roof panels (21L, 21R) to the roof structure. Secured with screws (S4, F7).

Parts Used: 21L (1), 21R (1), S4 (8), F7 (2).

Step 13: Attach Roof Panels (W12)

Attach roof panels (W12) to the roof structure. Secured with screws (S4, F4, F7).

Parts Used: W12 (2), S4 (12), F4 (4), F7 (12).

Step 14: Attach Roof Panels (W15)

Attach roof panels (W15) to the roof structure. Secured with screws (S4, F7).

Parts Used: W15 (2), S4 (12), F7 (12).

Step 15: Attach Roof Panels

Attach remaining roof panels. Secured with screws (S4, F7).

Parts Used: S4 (6), F7 (6).

Step 16: Attach Roof Panels

Attach remaining roof panels. Secured with screws (S4, F7).

Parts Used: 20 (2), S4 (4), F7 (4).

Step 17: Attach Roof Panels

Attach remaining roof panels (19). Secured with screws (S4, F7).

Parts Used: 19 (4), S4 (6), F7 (6).

Step 18: Attach Door Frame Supports

Attach door frame supports using parts F4, S8, and F7.

Parts Used: F4 (4), S8 (4), F7 (4).

Step 19: Attach Door Panels

Attach door panels using part F8.

Parts Used: F8 (20).

Step 20: Assemble the Door

This step details the assembly of the door. It shows attaching door frame components (15, 16, 21, 22, M1, S1, S5, S6, S7) and then the door itself to the shed structure.

The door on the left: Shows attaching parts 15, 16, 21, 22, M1, S1, S5, S6, S7, F7, S4 to form the door and frame.

The back of the door: Shows the rear view of the door assembly.

The front of the door: Shows the front view of the door assembly.

Parts Used: 15 (2), 16 (1), 21 (2), 22 (1), M1 (1), S1 (1), S5 (2), S6 (1), S7 (1), S4 (12), F7 (16).

Step 21: Assemble the Door (Right Side)

This step details the assembly of the second door (on the right). It shows attaching door frame components (15, 16, 21, 23, M1, S2, S3, S6, S7, S9) and then the door itself to the shed structure.

The door on the right: Shows attaching parts 15, 16, 21, 23, M1, S2, S3, S6, S7, S9, S4, F7 to form the door and frame.

The back of the door: Shows the rear view of the door assembly.

The front of the door: Shows the front view of the door assembly.

Parts Used: 15 (2), 16 (1), 21 (2), 23 (1), M1 (1), S2 (1), S3 (1), S6 (1), S7 (1), S9 (4), S4 (12), F7 (16).

Step 23: Final Assembly

This step shows the final assembly of the shed with doors attached. It involves securing the doors to the frame using parts S6, S7, S4, F7, and possibly other components like M1, S2, S3, S5, S9 depending on the specific door attachment mechanism.

The diagram shows the completed shed with both doors open, highlighting the attachment points with screws (S4, F7) and brackets.