Lutron Caséta Wireless In-Wall Dimmer Quick Start Guide

What's Included

• In-wall dimmer (PD-6WCL)
• Claro® wallplate (CW-1)
• Pico® remote control (PJ2-3BRL)
• Wire connectors (3)
• Screws (2)

Tools You'll Need

• Flat-head screwdriver
• Phillips-head screwdriver
• Pliers

Works with Energy Efficient Dimmable Light Bulbs

Compatible light bulbs include:

• LED: up to 150 W
• CFL: up to 150 W
• Halogen: up to 600 W
• Incandescent: up to 600 W

Note: Dimmable LED and CFL bulb performance can vary. For troubleshooting flickering or bulbs turning off, visit www.casetawireless.com/lowend. For a complete list of compatible bulbs, visit www.casetawireless.com/bulblist.

Compatible bulb models mentioned include: Cree®, Ecosmart®, Feit®, Philips®, Sylvania®.

Installing Your Dimmer (Single-Pole Installation)

WARNING: SHOCK HAZARD. May result in serious injury or death. Turn off power at circuit breaker or fuse before installing.

1. Turn Power Off: Turn off power at the circuit breaker.
2. Remove Existing Switch: Remove the wallplate from the switch. Unscrew the existing switch and pull it away from the wall. Disconnect all wires from the switch.
3. Remove Side Sections (if necessary): Bend side sections back and forth to remove them. Note: Do not remove outside side sections on dimmers at the end of a gang. A dimmer in the middle of a gang requires all side sections to be removed.
4. Connect the Dimmer:
   1. Connect the bare copper (or green) "ground" wire from the wallbox to the green wire on the dimmer using a wire connector.
   2. Connect either of the remaining wires from the wallbox to either of the remaining wires on the dimmer using a second wire connector.
   3. Connect the remaining wire from the wall to the remaining wire on the dimmer using a third wire connector.
5. Mount the Dimmer: Secure the dimmer into the wallbox using the provided screws.
6. Attach the Wallplate: Attach the adapter to the dimmer using the screws provided and snap on the wallplate. If installing next to other devices, ensure the wallplate has the correct number of openings.
7. Turn Power On: Turn power back on at the circuit breaker.

Note on 3-Way Switches: For lights with more than one wall switch (3-way applications), please visit www.casetawireless.com/3way for complete instructions and videos.

Using Your Caséta Wireless Kit

With a Smartphone or Tablet (Bridge Required)

The Caséta Wireless dimmer can be controlled from a smartphone when used with the Lutron® Smart Bridge™ (sold separately). Follow these steps:

• Download the Lutron® App: Search for "Lutron Caseta" in your app store.
• Launch the App: The Lutron® app will guide you through device setup.
• Add Devices: Use the app to add devices such as Pico® remotes, dimmers, and shades.

The app enables features like controlling lights three ways, scheduling, and remote access.

Without a Smartphone or Tablet (Bridge Not Required)

Pairing the Dimmer and Pico® Remote Control

1. Press and hold the "off" button on the dimmer for 6 seconds until LEDs start blinking.
2. Press and hold the "off" button on the Pico® remote control.
3. Set the desired light level on the dimmer.
4. Press and hold the "favorite" button on the Pico® remote control for 6 seconds until the lights flash 3 times.
5. Repeat these steps to pair additional Pico® remote controls.

Changing the Favorite Light Level (Optional)

You can set a preferred light level for the "favorite" button on the Pico® remote:

1. Set the desired light level on the dimmer.
2. Press and hold the "favorite" button on the Pico® remote control for 6 seconds until the LEDs blink twice. The new favorite level is now saved.

Troubleshooting

For additional troubleshooting suggestions, visit www.casetawireless.com/support.

Device Ratings

• In-wall dimmer: PD-6WCL, 120 V~ 50/60 Hz
• Pico® remote control: PJ2-3BRL, 3 V - 10 mA, (1) CR2032 battery (included)

Important Notes

• For indoor use only.
• Operate between 32 °F (0 °C) and 104 °F (40 °C).

Caution: Use only with permanently installed fixtures with dimmable LED, dimmable CFL, halogen, or incandescent lamps. Do not use to control receptacles, motor-driven appliances, or transformer-supplied appliances to avoid overheating and damage.

Codes and Compliance

Install in accordance with all national and local electrical codes.

Grounding: When no grounding means exist in the wallbox, the National Electrical Code (NEC®) allows installation if a nonmetallic faceplate is used or the circuit is protected by a GFCI. Cap or remove the green wire before screwing the control into the wallbox in these cases.

FCC/IC Information: This device complies with part 15 of the FCC Rules and Industry Canada license-exempt RSS standards. Operation is subject to two conditions: (1) no harmful interference, and (2) acceptance of any interference. Modifications not expressly approved by Lutron Electronics Co., Inc. may void the user's authority to operate this equipment. This equipment has been tested and found to comply with Class B digital device limits.

Trademarks: Lutron®, , Claro®, and Pico® are registered trademarks. FASS™, Caséta®, and Smart Bridge™ are trademarks of Lutron Electronics Co., Inc. NEC® is a registered trademark of the National Fire Protection Association. Google® and the Google logo are registered trademarks of Google Inc.

Copyright © 2014 Lutron Electronics Co., Inc.

For warranty information, please visit www.casetawireless.com/warranty.

FASS™ Front Accessible Service Switch

The FASS™ switch on the in-wall dimmer can be pulled out to remove power at the light socket, useful for replacing light bulbs.

Pico® Remote Control Buttons

• On: Turns the light on.
• Brighter: Increases light level.
• Favorite: Recalls a saved favorite light level.
• Darker: Decreases light level.
• Off: Turns the light off.