Primo Smart Touch Water Dispenser

Product Overview

The Primo Smart Touch Water Dispenser offers a clean, modern design that complements any kitchen or lifestyle. With the simple touch of a button, you can dispense water at three different temperatures: cold, cool, and hot.

Features

• Convenience Switches: Located on the back of the dispenser to control heating and cooling functions.
• Touch Controls: Intuitive touch icons for dispensing water.
• Cold Water: ❄️ Cold Water Icon - Touch to unlock and dispense. Hold for non-stop dispensing. Indicator light turns green when cooling.
• Cool Water: ? Cool Water Icon - Touch to unlock and dispense. Hold for non-stop dispensing.
• Hot Water: ? Hot Water Icon - Touch and hold to unlock and dispense. Release to stop. Indicator light turns red when heating. Child Safety: Requires holding both the dispense control and heating icon simultaneously for hot water dispensing.
• Dispense Control: Touch to dispense after unlocking the desired temperature. Touch again to stop. Flashes for non-stop dispensing.
• Empty Bottle Light: ⚠️ Blinks orange when the water bottle is empty and needs replacement.
• Probe Assembly: Pumps water from the bottle to the internal hot and cold tanks.
• Probe Hanger: Located inside the cabinet door to keep the probe assembly clean when not in use.
• Drip Tray: Removable and dishwasher-safe for easy cleaning.
• Water Bottle Compatibility: Uses 3-gallon or 5-gallon water bottles (not included).

Quick Start Guide

1. Place the dispenser on a level floor surface in your desired indoor location. Do not plug in the power cord until instructed.
2. Position the dispenser: ensure at least 4 inches of clearance from the wall at the back and 4 inches on both sides for proper airflow.
3. Clean the probe assembly with a damp cloth and mild dish soap. Place the clean probe assembly on the hanger inside the cabinet door.
4. Remove the cap from a Primo® water bottle (sold separately). Insert the probe assembly firmly into the bottle opening. For 3-gallon bottles, adjust the probe assembly collar as needed.
5. Slide the water bottle into the dispenser cabinet and close the door securely. The dispenser will not pump water if the door is not fully closed.
6. Plug the dispenser into a Ground Fault Circuit Interrupter (GFCI) outlet. The dispenser will begin pumping water to fill the internal reservoirs.
7. Turn on the heating and cooling switches located on the back of the dispenser. (Green light indicates cooling, Red light indicates heating).
8. Once the dispenser has finished filling the reservoirs, dispense and discard approximately one quart (about 2 pint glasses) of water from each spout (cold, cool, and hot) to flush the system.
9. Your water will be ready: Cold water will be fully chilled in approximately 1 hour, and hot water will be ready in approximately 12 minutes.
10. Register your dispenser at PrimoWater.com to activate your 1-year warranty.

Important Safety Precautions

• Read All Instructions: Before assembling, installing, or operating the dispenser.
• Proper Use: Intended for water dispensing only. Do not use other liquids.
• Installation: Install and operate only on a hard, flat, level surface. Ensure adequate ventilation (4 inches clearance at back and sides). Do not place in enclosed spaces or cabinets. Do not operate in the presence of explosive fumes.
• Electrical Safety: Use a GFCI outlet. Do not use extension cords. Never unplug by pulling the cord; grasp the plug. Do not use if the cord is damaged. Do not immerse the cord, plug, or unit in water. Unplug before cleaning.
• Hot Water Safety: Hot water is dispensed at very high temperatures. Always supervise children when they are dispensing hot water. Unplug the unit to prevent unsupervised use by children. Do not dispense hot water if the bottle is empty.
• Elevation: The dispenser performs best below 6,000 ft elevation.

Primo® Water Dispenser Limited Warranty

Primo Water North America ("Primo") warrants its Primo® Water Dispenser ("Dispenser") against defects in material and workmanship for a period of one (1) year from the date of purchase.

What is Covered:

• Defects in material and workmanship for one (1) year from the date of purchase.

What is Not Covered:

• Normal wear and tear.
• Damage or failure from improper installation, assembly, operation, or maintenance.
• Damage from accident, abuse, misuse, alteration, or misapplication.
• Damage to the finish (scratches, dents, discoloration, rust) occurring after purchase.

Obtaining Warranty Service:

• Contact Primo Customer Service online at primowater.com/contact-us/ or by phone at (844) 237-PRIMO.
• Proof of purchase may be required. Retain your receipt, order confirmation, or invoice.
• You may need to ship the dispenser or parts to Primo (customer pays initial shipping). Primo will pay return shipping for valid warranty claims.

Limitations:

• This warranty is for the original purchaser only and is not transferable.
• Primo's liability is limited to the purchase price of the dispenser.
• Primo is not liable for indirect, special, punitive, incidental, or consequential damages.

For more details or to register your product, visit PrimoWater.com.