JLab Fit Sport 3 Wireless Earbuds

Your Warranty

All warranty claims must be approved by JLab Audio and are at their sole discretion. Keep your proof of purchase to ensure coverage.

Contact Us

Contact us at support@jlabaudio.com or go to intl.jlabaudio.com/contact

Sign Up Today

Visit intl.jlabaudio.com/register for product updates, tips & tricks, and more.

First Setup: Pairing via Bluetooth

1. Step 1

   Turn on Bluetooth in your device settings.

   [Visual: Smartphone screen showing Bluetooth settings enabled.]

2. Step 2

   Press and hold the button on the earbuds for 10 seconds. Release. The light will flash red and blue to indicate pairing mode.

   [Visual: JLab Fit Sport 3 earbuds with indicator light flashing red and blue.]

3. Step 3

   Select "JLab BT" in your device's Bluetooth settings to connect. The light will flash slowly blue during Bluetooth pairing.

   [Visual: Smartphone screen showing "JLab BT" selected in Bluetooth settings. Earbuds shown with slow blue flashing light.]

Continued Use

Once the JLab Fit Sport 3 is connected to your device, the headphones will automatically connect when powered on. (Follow instructions for BUTTON FUNCTIONS)

Button Functions

• Turn Up Volume: Single click
• Go Forward: Press and hold for two seconds
• Power On: Press and hold for three seconds
• Power Off: Press and hold for five seconds
• Play/Pause / Answer Call / End Call: Single click
• Activate Siri (iOS) or "OK Google" (Android): Double click
• Pairing via Bluetooth: Follow the procedure for initial setup: Pairing via Bluetooth
• Turn Down Volume: Single click
• Go Back: Press and hold for two seconds

Equalizer Settings

Quickly press both buttons to cycle through different EQ settings (Fit Sport 3 cycles through three EQ settings):

• JLab SIGNATURE (One beep): JLab C3™ signature sound with enhanced vocals and bass
• BALANCED (Two beeps): Even sound without additional amplification
• BASS BOOST (Three beeps): Enhanced bass and sub-bass

Audio Cues

• POWER ON: Chime
• BLUETOOTH CONNECTED: Two beeps
• LOW BATTERY: "Low Battery" (under 20%)
• POWER OFF: Chime

Charging

1. Step 1

   Open the USB door and connect the cable to a computer or USB power source to charge the battery. Ensure the power source is rated 5V or lower.

   [Visual: Earbud charging port shown with USB cable connected to a computer.]

2. Step 2

   The light will glow red while charging and turn blue when fully charged.

   [Visual: Indicator light shown as red (charging) and blue (fully charged).]

Fitment

1. Step 1

   Select ear tip size and optional Cush Fin. Try different ear tips to find the best fit.

   [Visual: Ear tips and Cush Fin shown.]

2. Step 2

   Position the earphone for the desired fit using Adjustable Tip Placement.

   [Visual: Diagram showing how to adjust earphone placement.]

3. Step 3

   Start from behind and hook over the ear.

   [Visual: Earbud being hooked over the ear.]

4. Step 4

   Secure the cable in front, behind, and at the bottom.

   [Visual: Diagram showing cable routing for secure fit.]

Using the Cord Clips

1. Step 1

   Attach the cord clip approximately in the middle of the cord.

   [Visual: Cord clip being attached to the earbud wire.]

2. Step 2

   Clip it securely to the back or front of your shirt.

   [Visual: Cord clip attached to a shirt.]

Troubleshooting Connection Issues

I Can't See JLab BT on My Device

1. Turn off Bluetooth, then turn it back on in your device settings. [Visual: Smartphone screen showing Bluetooth toggled off and on.]
2. If JLab BT is still not visible, repeat the FIRST TIME SETUP: Pairing via Bluetooth instructions.

JLab BT Won't Connect to My Device When Powered On

1. Delete JLab BT from your device settings.
2. Turn off Bluetooth, then turn it back on in your device settings. [Visual: Smartphone screen showing Bluetooth toggled off and on.]
3. Follow the instructions again for FIRST SETUP: Pairing via Bluetooth. [Visual: Smartphone screen showing re-pairing process.]

Bluetooth is Connected to an Unwanted Device

Note: JLab BT can remember up to eight devices. It will automatically attempt to connect to the last used device.

1. If you have had more than one device connected to JLab BT, turn OFF Bluetooth on the unwanted devices and turn ON Bluetooth on the desired device.
2. Press and hold the button for 10 seconds. Release. The light will flash red and blue to indicate pairing mode. Select "JLab BT" in your device's Bluetooth settings to connect. The light will flash slowly blue during Bluetooth pairing. [Visual: Smartphone screen showing selection of "JLab BT" after pairing mode.]

Warnings

Charging Warning

Ensure the USB door is closed and secured. This will protect against damage from sweat and water.

Fit Sport 3 earbuds must be completely dry before charging. Internal components can be damaged if exposed to moisture. The headphones should air dry before charging.

General Warnings

• Avoid moisture or liquid in the ear tips or charging port.
• Avoid extreme heat, cold, or humidity.
• Avoid dropping or crushing your headphones, stressing the cord by pulling quickly or hard, or kinking the cord.
• Earwax can build up in the ear tips and degrade sound quality. Gently remove wax with a cotton swab or other suitable tool to improve sound quality.
• Try lowering the volume if you experience discomfort or pain, or stop use temporarily.
• If you experience regular discomfort while using this product, stop using it immediately and consult a doctor.
• We recommend treating your headphones like a pair of expensive sunglasses and storing them in a safe place when not in use.