Ecler VEO-XPS47 4K 18Gbps HDMI® Extender Kit with Audio Extraction

1. Safety Precautions

1.1 Important Preliminary Note

The lightning symbol within an equilateral triangle warns the user of non-isolated, dangerous voltage within the product housing that could be sufficient to cause an electric shock.

The exclamation mark within an equilateral triangle indicates that the user should refer to the accompanying documentation for important operating and maintenance instructions.

WARNING (if applicable): Connections marked with the symbol "⚡" may pose a risk of electric shock. External wiring connected to the terminals must be performed by qualified personnel or using pre-assembled cables.

WARNING: For fire and electric shock protection, the device must always be protected from moisture and humidity.

CAUTION: Class I safety devices must only be connected to earthed mains sockets with a protective earth conductor.

CAUTION: Ecler products have a long lifespan of more than 10 years. This product must not be disposed of as unsorted municipal waste under any circumstances. Please dispose of it at the nearest recycling center for electrical and electronic waste.

1.2 Important Safety Instructions

1. Read this manual thoroughly.
2. Keep this manual in a safe place.
3. Observe all warning labels.
4. Follow all instructions.
5. Do not use the device near water.
6. Clean only with a dry cloth.
7. Ensure that all ventilation openings remain unobstructed. Install the device according to the manufacturer's instructions.
8. Do not place the device near heat sources such as radiators, ovens, or other heat-generating appliances (including amplifiers).
9. Never disable the safety function of a polarized or earthed plug. A polarized plug has two pins of different widths. An earthed plug has two pins and a third earth pin. This third pin is for your safety. If the supplied plug does not fit your socket, have it replaced by a qualified electrician.
10. Ensure that the power cord cannot be pinched, twisted, or stepped on, especially at the plugs, connection sockets, and the point where the cable exits the device.
11. Only use accessories/add-on parts specified by the manufacturer.
12. Disconnect the device from the mains during thunderstorms or when it will not be used for extended periods.
13. Only allow qualified service personnel to perform service work. Service is required when the device has been damaged in any way, such as damage to the power cord or plug, if liquids or foreign objects have entered the device, if the device has been exposed to rain or moisture, if it does not operate normally, or if it has been dropped.
14. Power Supply Disconnection: Turning off the device using the POWER switch interrupts all functions and indicator lights. However, to completely disconnect the device from the mains, the power cord must be removed from the mains socket. This must therefore always be easily accessible.
15. The device is connected to an earthed socket via a power cord.
16. The specifications are located on the top/back of the device.
17. Protect the device from dripping or splashing water, and do not place any liquid-filled containers (e.g., flower vases) on it.

1.3 Cleaning

Always clean the device with a soft, dry cloth or a cloth slightly dampened with water and mild liquid soap. Ensure that no liquid enters the device through any openings. Do not use alcohol, gasoline, solvents, or abrasive cleaners.

NEEC AUDIO BARCELONA, S.L. is not liable for any damage to persons, animals, or objects caused by failure to comply with the above warnings.

2. Warranty and Environment

Thank you for choosing our Ecler VEO-XPS47 model. To ensure optimal operation and performance, it is VERY IMPORTANT to read and follow the instructions in this manual before connecting the device.

For optimal device performance, we recommend that maintenance be carried out exclusively by our authorized technical service partners.

All ECLER products have a warranty. The validity period and conditions can be found at www.ecler.com or on the warranty card included with the device.

Ecler is committed to environmental protection and reducing CO2 emissions. The use of recyclable materials and non-polluting components is also a top priority in our environmental commitment.

Ecler has evaluated, analyzed, and mitigated, reduced, and/or compensated for the environmental impact of all processes involved in the manufacturing of this product, including packaging.

3. Package Contents

• 1 x Sender VEO-XPS47.
• 1 x Receiver VEO-XPS47.
• 1 x 12VDC 1A Universal Power Supply (one power supply for both devices).
• 1 x IR Blaster.
• 1 x IR Receiver.
• 4 x Mounting ears.
• 8 x Mounting screws.
• 1 x USB 2.0 Cable.
• 2 x Euroblock connectors for RS-232 and audio cable connection.
• 1 x Firmware Update USB Adapter for Firmware Update (If you need help updating the firmware, please contact our Technical Support department).
• Quick Guide.
• Warranty Card.

4. Description and Features

The VEO-XPS47 is an HDMI® 18Gbps extender kit that extends 4K 50Hz 4:4:4 video signals with zero latency over a single Cat 5e or higher category cable up to 70 meters. It features unbalanced stereo audio extraction via Euroblock connectors on both the sender and receiver, as well as EDID management, IR signal pass-through, and bidirectional PoC support, making it a simple and cost-effective solution for professional extension applications.

4.1 Key Features

• Sender and receiver set for signal extension over a single Cat 5e or higher category cable.
• Supports HDMI® 18Gbps 4K 60Hz 4:4:4 as described in HDMI® 2.0b.
• Transmission range for 4K/50Hz up to 70 meters and 4K/60Hz up to 30 meters.
• Unbalanced stereo audio output via Euroblock connectors on the sender and receiver.
• Supports HDR10, HDR10+, Dolby Vision, and HLG.
• Supports audio formats LPCM 7.1, Dolby True HD, DTS HD Master.
• Bidirectional IR control extension.
• EDID management.
• HDCP 2.2 compliant.
• Bidirectional PoC function.

5. Control Panel Functions

5.1 Sender: Front and Rear Panel

1. EDID: Used to select EDID settings. When the switch is in the right position, the extender copies the EDID information from the HDMI® loop-out to the source; when in the left position, it copies the EDID information from the receiver to the source.

2. SERVICE: Micro-USB connector for firmware upgrades and custom EDID uploads.

3. AUDIO OUT: Unbalanced stereo audio extraction.

4. IN: HDMI® input connector.

5. CAT OUT: Connect this to the receiver's input using a Cat 5e or higher category cable. Only point-to-point connections are allowed.

6. IR IN: 3.5mm jack for connecting the IR receiver for IR pass-through.

7. IR OUT: 3.5mm jack for connecting to the IR blaster to transmit an IR signal from the display to the source.

8. DC 12V: Connect the supplied 12V DC power adapter here.

5.2 Receiver: Front and Rear Panel

1. SERVICE: Micro-USB connector for firmware upgrades and custom EDID uploads.

2. OUT: HDMI® output. Connect it to the display device (e.g., 4K TV screen).

3. AUDIO OUT: Unbalanced stereo audio extraction.

4. CAT IN: Connect this using a Cat 5e or higher category cable to the receiver's input. Only point-to-point connections are allowed.

5. IR IN: Connect this to the supplied IR receiver to extend an IR signal from the display to the source.

6. IR OUT: 3.5mm jack for connecting the IR receiver for IR pass-through.

7. DC 12V: Connect the supplied 12V DC power adapter here.

6. Installation and Connection

To avoid connection problems and malfunctions, high-quality standard Ethernet cables of Category 5e (or higher) are required for connecting the sender to the receiver. To ensure a good signal reference for the receiver and to avoid electromagnetic interference along the cable, shielded cables and connectors are absolutely necessary.

Please be careful when inserting or removing HDMI® cables.

1. HDMI® signal sources, e.g., Blu-Ray players, STBs, etc.: Connect the devices to the HDMI® input of the VEO-XPS47 sender.
2. HDMI® display devices, e.g., 4K or 1080p screens or projectors: Connect the devices to the HDMI® output of the VEO-XPS47 receiver.
3. IR Blaster: Connect this to the IR-Out connector of the VEO-XPS47 sender and/or receiver.
4. IR Receiver: Connect this to the IR-In connector of the VEO-XPS47 sender and/or receiver.

IR Blaster Diagram:

• 1. IR Blaster Signal
• 2. Power
• 3. NC (Not Connected)

IR Receiver Diagram:

• 1. IR Signal
• 2. Power
• 3. Grounding

7. Technical Data

7.1 Technical Specifications

VEO-XPS47

Video Performances

• Video Input Connectors (Transmitter): 1 x HDMI® Type A Female, 2.0, 18Gbps; 1 x RJ-45 Female
• Video Output Connectors (Receiver): 1 x HDMI® Type A Female, 2.0, 18Gbps; 1 x RJ-45 Female
• Video Input Resolutions: 480i, 480p, 720i, 720p, 1080i, 1080p up to 60Hz, 1200p up to 25/30Hz, 4K up to 60Hz
• Video Output Resolutions: 480i, 480p, 720i, 720p, 1080i, 1080p up to 60Hz, 1200p up to 25/30Hz, 4K up to 60Hz
• Chroma Subsampling: 4:4:4, 4:2:2, 4:2:0
• Colour Depth: 8-bit (4K 60Hz 4:4:4), 10-bit / 12-bit (4K 60Hz 4:2:2 – 4:2:0)
• Colour Space: RGB, YCbCr 4:4:4 YCbCr 4:2:2, YCbCr 4:2:0
• HDCP: HDCP 2.2
• HDR: HDR10, HDR10+, Dolby Vision, HLG
• HDMI® Distance: Up to 4K/60Hz: 5m with IN/OUT HDMI® Cable

Audio Performances

• Audio Formats: LPCM 2.0/2.1/5.1/6.1/7.1, Dolby Digital, Dolby TrueHD, Dolby Digital Plus(DD+), DTS-ES, DTS HD Master, DTS HD-HRA, DTS-X
• Sample Rate: 48 KHz, 96 KHz, 192 KHz
• Bit Depth: Up to 24-bit
• Frequency Response: 20Hz-20KHz (±3dB)

Device Control

• Control Connectors: 1 x DIP Switch
• EDID Management: EDID Copy, EDID Setting
• Status Indicators: Link Status LEDs

Pass-Through Control

• Pass-through Connectors: 1 x Jack 3.5mm
• Pass-through Protocols: IR

Connection Specification

• HDMI® extension: Point-to-Point extension with zero latency
• Transmission Distance: 4K/50Hz up to 70m with Cat 5e or higher; 4K/30Hz up to 30m with Cat 5e or higher

Electrical

• Power Supply: PoC bidirectional; External: Input 100-240VAC 50/60Hz 0.3A, Output DC 12VDC-1A
• AC Mains Connector: External PSU. Included 4 region power blades (UK,US,AU,EU)
• DC Mains Connector: DC Locking
• Power Consumption: 3.36W

Physical

• Operating Temperature: Min: 0°C; 32°F; Max: 40°C; 104°F
• Operating Humidity: 20% - 80% RH, non-condensing
• Storage temperature: Min: -20°C ; -4°F; Max: 60°C; 140°F
• Storage humidity: 10% - 90% RH, non-condensing

7.2 Mechanical Diagram

All measurements in mm.

7.2.1 Sender

Diagram of Sender: Shows front, top, and side views with dimensions labeled in mm. Key ports indicated are HDMI IN, CAT OUT, IR IN, IR OUT, DC 12V, and AUDIO OUT. The overall dimensions are 90mm (width) x 18mm (height) x 68mm (depth).

7.2.2 Receiver

Diagram of Receiver: Shows front, top, and side views with dimensions labeled in mm. Key ports indicated are HDMI OUT, CAT IN, IR IN, IR OUT, DC 12V, and AUDIO OUT. The overall dimensions are 90mm (width) x 18mm (height) x 68mm (depth).

Additional Information

Installation Options: Mounting ears for table, wall, or screwed installation.

Included Accessories: 1 x IR Receiver cable (1.5 meters), 1 x IR Blaster cable (1.5 meters), 2 x 3-pin 3.5mm Euroblock connectors, 4 x Mounting ears, 8 x Mounting screws, 1 x USB 2.0 Cable, 1 x Firmware Update USB Adapter, 1 x PSU 12V/1A.

Dimensions (WxHxD): Transmitter/Receiver: 90 x 18 x 68mm / 3.54 x 0.71 x 2.68 in.

Shipping Dimensions (WxHxD): 215 x 75 x 135mm / 8.47 x 2.95 x 5.31 in.

Weight: Transmitter: 0.160 Kg / 0.35 lb; Receiver: 0.155 Kg / 0.34 lb.

Shipping Weight: 0.7kg / 1.54 lb.

Chassis Material: Metal.

Finished Colour: Black.