Eurolite LED PFE-60 WW/CW Profile Spot
User Manual
Introduction
Thank you for choosing a Eurolite product. This manual provides instructions for safe and optimal use, ensuring long-term satisfaction.
Product Features
- Profile spotlight with 60W WW/CW LED, manual zoom, and shutter blades.
- Equipped with a powerful 60W COB (Chip-on-board) WW/CW LED.
- Variable color temperature from 3200K to 5600K.
- Suitable for application areas such as stages and theaters.
- Operable in 2-channel or 5-channel DMX modes.
- Features temperature-controlled fan cooling.
- Controllable via Stand-alone, Master/Slave, DMX, and RDM modes.
- Available with beam angles of 9-25° (Article No. 40001721) and 20-50° (Article No. 40001722).
- High Color Rendering Index (CRI) of 94 Ra.
- Multicolor OLED display for status information.
- Includes Dimmer and Strobe effects.
- Variable PWM frequency (Pulse-Width Modulation) for smooth dimming.
- Manual zoom adjustment.
- Swivel mounting bracket included.
- Flicker-free operation.
Safety Instructions
General Warnings
Read all safety warnings carefully and use the product only as described in this manual to prevent accidental injury or damage.
Intended Use
This device is an LED profile spotlight for professional lighting effects in event technology (e.g., stages). It is not intended for household lighting.
Use the device strictly according to these instructions. Failure to comply voids the warranty and the manufacturer assumes no liability for damages resulting from improper use or non-compliance.
Danger Due to Electricity
The device is for indoor use only. Never expose it to rain, moisture, or use outdoors. Do not open the device; there are no user-serviceable parts inside.
Connect only to a properly installed, grounded mains outlet matching the device's voltage and frequency. Ensure the outlet has residual current protection (RCD). Never disable the protective ground. The mains outlet should be easily accessible for quick unplugging.
Never touch the mains plug with wet hands. Do not bend or squeeze the mains cable. Keep it away from hot surfaces and sharp edges. Always pull the plug, not the cable, to disconnect.
Unplug during lightning storms, long periods of non-use, or before cleaning. Avoid high temperatures, direct sunlight, splashing water, strong vibrations, and heavy mechanical stress.
Do not place liquid-filled objects or open flames near the device. Ensure no objects, especially metal parts, can fall into the device.
Repairs must be performed by qualified personnel only. Cleaning is limited to the exterior surface with a soft, damp, lint-free cloth. Avoid solvents or aggressive detergents. Ensure no moisture enters connection areas.
Danger to Children and People with Restricted Abilities
This product is not a toy. Keep it away from children and pets. Do not leave packaging material carelessly. Never leave the device running unattended.
The device should only be used by persons with sufficient physical, sensory, and intellectual abilities, knowledge, and experience. Others must be supervised by a responsible person.
Warning - Risk of Burns and Fire
Admissible ambient temperature range (Ta) is -5 to +45°C. Do not operate outside this range. Housing temperature (Tc) can reach up to 85°C; avoid contact.
Maintain a minimum distance of 20 cm from illuminated surfaces. Keep the device away from flammable materials and ensure adequate air circulation (50 cm clearance). Do not cover ventilation openings.
Warning - Risk of Injuries
Do not look directly into the light source, as it may cause epileptic seizures in sensitive individuals.
Ensure the product is installed safely and securely to prevent falling. Comply with national safety regulations (e.g., EN 60598-2-17). If unqualified, use a professional installer.
For overhead use, always secure the device with a secondary safety attachment (e.g., safety bond or net). Ensure the area below the installation is clear during rigging and servicing.
Caution - Material Damage
Do not connect the device to mains voltage via a dimmer. Lighting effects are not designed for continuous operation; use breaks to prolong lifespan.
Avoid frequent on/off switching. If exposed to drastic temperature changes, allow the device to reach room temperature before operation to prevent condensation damage.
Use original packaging for transport and storage. Do not remove serial number labels, as this voids the warranty.
Device Description
The device is a profile spotlight featuring a 60W WW/CW LED. The following describes the main components:
Main Unit Components
- (1) Mounting bracket: For attaching the fixture.
- (2) Gobo holder: For inserting gobos (patterns).
- (3) Fixation screw: Secures the mounting bracket or other adjustments.
- (4) Shutter blades: Used to shape the light beam.
- (5) Lens / LED: The primary light source and lens assembly.
- (6) Housing: The main body of the fixture.
Adjustment Components
- (7) Manual Zoom - Fixation screw: Secures the zoom adjustment.
- (8) Manual Focus - Fixation screw: Secures the focus adjustment.
Rear/Side Panel Components
- (9) Safety eyelet: For attaching a safety bond.
- (10) OLED display: Shows operational status and settings.
- (11) Encoder: Used for menu navigation and value adjustment.
- (12) DMX in: XLR connector for receiving DMX signals.
- (13) DMX out: XLR connector for sending DMX signals to other devices.
- (14) Fuse holder: Contains the main fuse.
- (15) Power input: Connector for the mains power cable.
Installation
WARNING! Risk of injury caused by falling objects. Overhead installations require secure mounting by a qualified specialist familiar with hazards and regulations.
The product is designed for overhead rigging via the mounting bracket, attachable to walls, ceilings, or trusses using appropriate couplers. It must not swing freely.
- Rigging structure must support at least 10 times the weight of all fixtures.
- Block the work area below and use a stable platform during installation.
- Use compatible rigging hardware capable of bearing the device's weight. Refer to Accessories for suitable hardware.
- Secure the device with a secondary safety attachment (e.g., safety bond) dimensioned according to safety regulations. This ensures no part falls if the main attachment fails. The safety bond should limit the drop distance to 20 cm.
- To align the device, loosen fixation screws on the mounting bracket, adjust the inclination angle, and retighten the screws.
- Periodically inspect the device after installation to prevent corrosion, deformation, or looseness.
Connections
Power Supply
Insert the power plug into a grounded safety socket to turn the device on.
DMX512 Control
A DMX512 data link is required for DMX control, using 3-pin XLR connectors.
DMX Daisy-Chaining: Connect the DMX controller output to the DMX IN of the first device. Connect the DMX OUT of each device to the DMX IN of the next device in the chain.
Termination: The last device in the chain must have its DMX output terminated with a 120 Ω resistor between Signal (-) and Signal (+).
Signal Amplification: For cable lengths over 300 m or more than 32 devices, use a DMX level amplifier for reliable data transmission.
XLR Connection Pinout
DMX Output (XLR Socket): Pin 1: Ground, Pin 2: Signal (-), Pin 3: Signal (+)
DMX Input (XLR Plug): Pin 1: Ground, Pin 2: Signal (-), Pin 3: Signal (+)
Operation
The device is ready after connecting to mains power. The display shows the last operating mode. Use the encoder to navigate the menu, select items, and adjust values. Settings are stored when power is disconnected.
Encoder Function
The encoder selects operating modes and activates values for modification or saving.
Menu Structure Overview
| Display | Function |
|---|---|
| DMX Address | Sets DMX start address (A001 – A512). |
| WW | Sets Warm White LED brightness (000 – 255). |
| CW | Sets Cold White LED brightness (000 – 255). |
| DIM CCT | Sets fixture color temperature (3200K – 5600K). |
| Intensity | Sets total brightness (000 – 255). |
| DIM Strobe | Sets strobe speed (000 – 012). |
| Curve | Selects dimmer curves (Linear, Exponential, Logarithmic, S-type). |
| Mode | Sets DMX channel mode (2CH or 5CH). |
| PWMrate | Sets PWM frequency (800Hz – 25000Hz). |
Stand Alone Mode
DIM (WW/CW): Adjust brightness for Warm White (WW) or Cold White (CW) LEDs from 000 to 255.
CCT: Adjust color temperature from 3200K to 5600K.
Intensity: Adjust overall brightness from 000 to 255.
DIM Strobe: Adjust strobe speed from 000 to 012.
Curve: Select dimmer curve type:
- Linear: Brightness increases linearly with DMX value.
- Exponential: Finer control at low levels, coarser at high levels.
- Logarithmic: Coarser control at low levels, finer at high levels.
- S-type: Fine control at low and high levels, coarser at medium levels.
Mode: Set DMX channel mode (2CH or 5CH). Default is 2CH.
PWM rate: Adjust PWM frequency from 800Hz to 25000Hz.
Manual Focus and Zoom Adjustment
Loosen the respective fixation screw, slide the lens-housing forward or backward to adjust focus or zoom, then retighten the screw.
Master/Slave Operation
Up to 32 devices can be interconnected. Configure all slave units with the same DMX address ("A001"). Connect DMX OUT of master to DMX IN of the first slave, and so on. The master unit must not be connected to a DMX controller. Set the master to the desired mode (Dimmer or Strobe) for synchronized operation.
DMX Operation
The device has 5 DMX channels, switchable to 2 channels. Set the DMX start address (refer to controller documentation). Navigate to "Mode" and select 2CH or 5CH.
The display indicates DMX signal reception. If no signals are received, the display flashes. Ensure DMX channels do not overlap for independent control; devices set to the same address will operate synchronously.
Functions in DMX Mode
2-Channel Mode
| Channel | Value | Function |
|---|---|---|
| 1 | 000 - 255 | Dimmer 3200K (0-100% brightness) |
| 2 | 000 - 255 | Dimmer 5600K (0-100% brightness) |
5-Channel Mode
| Channel | Value | Function |
|---|---|---|
| 1 | 000 - 255 | Dimmer 3200K (0-100% brightness) |
| 2 | 000 - 255 | Dimmer 5600K (0-100% brightness) |
| 3 | 000 - 255 | Color Temperature (3200K - 5600K) |
| 4 | 000-009 | No function |
| 010-255 | Strobe effect (0-100% speed) | |
| 5 | 000 - 255 | Master dimmer (0-100% total brightness) |
Cleaning and Maintenance
Periodically clean the exterior with a soft, damp, lint-free cloth. Ensure no liquids enter the device. Never use alcohol or solvents.
Fuse Replacement: If the fuse blows, replace it with one of the same type and rating. Disconnect power, open the fuse holder with a screwdriver, replace the fuse, and reinsert the holder.
Internal components are not user-serviceable. Do not attempt repairs; contact authorized dealers for service or spare parts.
Protecting the Environment
Disposal of Old Equipment: Do not dispose of this device as household waste. Take it to a local recycling plant. Remove and dispose of batteries separately according to local regulations.
Technical Specifications
| Specification | Value |
|---|---|
| Article No. | 40001721, 40001722 |
| Power Supply | 100-240 V AC, 50/60 Hz |
| Power Consumption | 60 W |
| IP Classification | IP20 |
| Protection Class | Class I |
| Power Connection | Fixed power cord with safety plug |
| Fuse | T 1 A, replaceable |
| Lamp Type | LED lamp |
| LED | 1 x 60 W COB WW/CW |
| Color Temperature | 3200K - 5600K |
| Equipment | Manual Zoom, Manual Focus |
| DMX Channels | 2; 5 |
| DMX Input | 3-pin XLR (M) |
| DMX Output | 3-pin XLR (F) |
| Cooling | Temperature-controlled fan |
| Control | Stand-alone, Master/Slave, DMX, RDM |
| Beam Angle | 9-25° (40001721), 20-50° (40001722) |
| Color Rendering Index (CRI) | 94 Ra |
| Housing Color | Black |
| Display Type | Multicolor OLED |
| Energy Efficiency Class | F |
| Gobos | Outside diameter 37mm, Image diameter 25mm |
| Dimensions (40001721) | Length: 42.5 cm, Width: 16.0 cm, Height: 25.5 cm, Diameter: Ø 11.5 cm |
| Dimensions (40001722) | Length: 35.0 cm, Width: 16.0 cm, Height: 25.5 cm, Diameter: Ø 11.5 cm |
| Weight (40001721) | 3.30 kg |
| Weight (40001722) | 3.10 kg |
Accessories
- EUROLITE TPC-10 Coupler, silver (No. 59006856)
- EUROLITE Safety Bond A 3x600mm up to 5kg, silver (No. 58010310)
- EUROLITE DMX cable XLR 3pin 3m black (No. 3022785H)
- EUROLITE Gobo Holder for LED PFE-60 (No. 40001710)
All information is subject to change without prior notice. © 13.09.2023
Eurolite is a brand of Steinigke Showtechnic GmbH, Andreas-Bauer-Str. 5, 97297 Waldbüttelbrunn, Germany.
