QUICK SETUP GUIDE

Before Installation

• This product may require cabling. It is highly recommended that all products and components be tested prior to installation.
• Fully charge your cameras overnight using the USB charger cable before installation.
• We don't recommend you set the camera to record continuously (24/7) because doing so may quickly deplete the battery (even on solar charging). We recommend you set it to record only when motion is detected. For how long does your battery last before it drains, refer to FAQ at the end of this manual.

Tech Support

For product introduction & specifications, please visit www.isansco.com. For FAQ, troubleshooting, or customer support, email us at support@isansco.com. We guarantee a reply within 24 hours.

FCC CLASS B NOTICE

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception (which can be determined by turning the equipment on and off), the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio or television technician for assistance

This equipment has been certified and found to comply with the limits regulated by FCC, EMC, and LVD. Therefore, it is designated to provide reasonable protection against interference and will not cause interference with other appliance usage. However, it is imperative that the user follows this manual's guidelines to avoid improper usage which may result in damage to the unit, electrical shock, and fire hazard injury. In order to improve the feature functions and quality of this product, the specifications are subject to change without notice from time to time.

Caution:

Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

View on Your Mobile Phone (EseeCloud)

1. App Remote Viewing

1.1 Download the app EseeCloud from App Store, or Google Play.

Note: iOS 9.0 or above, Android 5.1 or above.

[EseeCloud App Icon] [QR Code for App Download]

Search and download EseeCloud to your mobile phone from App Store/Google Play. Or simply scan this QR Code to download.

1.2 Register and Login

Step 1. On the app, press Register. Enter your Email or Phone Number, then press Confirm.

Step 2. Enter the Verification Code, and set up your Password.

Step 3. Go back to the login screen, enter your details and press Confirm to log in.

[Image showing registration screen with fields for email/phone and confirm button]

[Image showing verification code screen with fields for code and password, and a 'get verification code again' option]

[Image showing login screen with fields for username/password and confirm button, with 'forget password' and 'remember password' options]

2. Add Device

Step 1. Press + (top right corner) to add your device.

Step 2. Scan the Cloud ID of the camera.

Step 3. Enter the Password for the camera.

Step 4. Name the camera and press Confirm.

[Image sequence showing device addition steps: Group, Add Device, Scan code successfully, Configure the device]

3. Live View & Playback on App

On the Device List, press the device thumbnail to enter the Live View interface, or press Playback to view the recorded footage.

[Image showing the EseeCloud app interface with device list, live view, and playback options]

How to Set up Push Alerts on Mobile Phone

On the App - go to Live View > Setting > Push messages > App push alert message, turn it on.

[Image showing app settings for push notifications]

On your Phone - iPhone user: go to Settings > Notifications > EseeCloud > Allow Notifications, and turn it on. Android user: go to Settings > Notifications & Status Bar > EseeCloud > Allow Notifications, and turn it on. See below:

[Image showing iPhone notification settings for EseeCloud]

[Image showing Android notification settings for EseeCloud]

After this, you will receive real-time push alerts whenever motion is detected by the camera.

Some tips about installing the solar panel:

[Image showing correct and incorrect solar panel placement: X for blocked by objects, X for horizontal placement, checkmark for clean and unobstructed]

• Make sure the solar panel is not blocked by buildings, trees, or objects that may cast shadow on it.
• Don't install the solar panel horizontally to avoid the accumulation of dust and debris.
• Wipe the solar panel regularly to keep it clean and not obscured by dust or dirt.

FAQs

Question: Does the camera record sound?

Answer: Yes, the camera records sound as well as video. Please note that each camera has built-in microphone, you will be able to not only view what's happening but hear what's being said. At the bottom of each split window, click on the speaker icon to mute or unmute. See below:

[Image showing app interface with speaker and microphone icons]

On your app: Eseecloud, you can press microphone icon to speak to the camera, and press the speaker icon to hear the camera.

Question: Why does the battery drain so fast?

Answer: 1. Go to Recording Mode (Right click the mouse > Camera Setup > Recording Mode), select Best Recording. Do not use Keep Recording! (Page 16) 2. Check the daily triggered alarm messages via the app (Event > Alarm Message). If there are too many false alarms, lower the motion sensitivity via Intelligent Detection Alarm Settings. 3. Check the signal strength of the camera. If the signal is too weak, try changing the camera position, fine tune the camera antenna, or set up the Auto Repeater to improve the signal transmission. (FAQ - How to boost the camera's WiFi signal?)

The battery life (see the left picture) for a fully charged camera (not on solar charging):

Alarm 3-5 times / day for about 180 days

Alarm 20 times / day for about 30 days

Alarm 30 times / day for about 20 days

Alarm 50 times / day for about 10 days

Question: The night vision of my camera is terrible?

Answer: 1. Make sure not to aim your camera towards something in front of the lens. 2. Do not face the camera towards glass, mirror, etc. 3. Do not face the camera lens towards direct lamps or sunlight. 4. Use ambient lamp to increase the lighting level.

Question: My camera is getting misty inside, is there a known fix?

Answer: This is probably because of condensation, which occurs in a humid environment as a result of the difference of the temperatures of the air and the object on which it occurs. In most cases it will clear up itself. However, if the condensation remains, you may send it back for replacement, please contact us immediately.

[CE logo] [UKCA logo] [FCC logo] [WEEE symbol] [Recycling symbol]

Made in China