Corelite BRYX Surface-Mount Installation Instructions

⚠️ WARNING

Risk of Fire, Electrical Shock, Cuts or other Casualty Hazards- Installation and maintenance of this product must be performed by a qualified electrician. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and hazards involved.

⚡ Risk of Fire and Electric Shock- Make certain power is OFF before starting installation or attempting any maintenance. Disconnect power at fuse or circuit breaker.

? Risk of Fire- Minimum 90°C supply conductors.

?️ Risk of Burn- Disconnect power and allow fixture to cool before handling or servicing.

⚠️ Risk of Personal Injury- Due to sharp edges, handle with care.

Failure to comply with these instructions may result in death, serious bodily injury and property damage.

DISCLAIMER OF LIABILITY: Cooper Lighting Solutions assumes no liability for damages or losses of any kind that may arise from the improper, careless, or negligent installation, handling or use of this product.

IMPORTANT: Read carefully before installing fixture. Retain for future reference.

NOTICE: Green ground screw provided in proper location. Do not relocate.

NOTICE: Fixture may become damaged and/or unstable if not installed properly.

Note: Specifications and dimensions subject to change without notice.

ATTENTION Receiving Department: Note actual fixture description of any shortage or noticeable damage on delivery receipt. File claim for common carrier (LTL) directly with carrier. Claims for concealed damage must be filed within 15 days of delivery. All damaged material, complete with original packing must be retained.

Wiring Guide

Power Supply (Input)

Black (BK) - Hot
White (WT) - Neutral
Green (GN) - Ground
Violet (VT) - Dimming (+)
Pink (PK) - Dimming (-)

Power Supply (Input) - When Applicable

Black/Red (BK/RD) - Emergency Hot
White/Red (WT/RD) - Emergency Neutral
Black/Orange (BK/OR) - 2nd Circuit Hot
White/Orange (WT/OR) - 2nd Circuit Neutral
Orange (OR) - 2nd Circuit Dimming (+)
Yellow (YL) - 2nd Circuit Dimming (-)
Blue (BL) - Battery/Emergency Unswitched Hot

Parts List

Luminaire (NOTE: Run configurations will consist of beginning of run (BOR), end of run (EOR) and intermediate fixtures.)
Joiner (continuous runs only)
Shielded Cable (by others)
Push-in Wire Connectors or Wire Nuts (pre-installed)
11/32" Flexible Nut Driver (by others)
#2 Philips Screwdriver (by others)
1/4-20 Screws/Bolts (by others)
Suction cup for lens positioning

Installation Instructions

Turn off the power before installation. Prior to drywall installation: Install shielded cable to accommodate electrical feed point on first fixture. Leave the protective film on the lift and shift diffuser and set aside. Unscrew LED tray from housing (screws will be on one side only). Tray will swing down to access the inside of the fixture.

Diagram Description: Shows the luminaire housing with the LED tray partially lowered, revealing the interior.
Remove 1/4" knockouts in top of housing. Remove access plate from fixture and Secure shielded cable to the 7/8" opening in the access plate for wire connections. Once attached, re-attach access plate and make wiring connections.

Diagram Description: Shows the top of the luminaire housing with knockouts removed, the access plate detached, and a flexible conduit with shielded cable being routed through the access plate opening.
Lift fixture to ceiling and use 1/2-20 bolts/screws to attach fixture to ceiling structure through 1/4" knockouts from step 2. Connect wiring from shielded cable to fixture wiring with wire nuts or push connectors. INDIVIDUAL FIXTURE INSTALLATION, SKIP TO STEP 8.

Diagram Description: Shows the luminaire being lifted and attached to the ceiling structure with bolts. A close-up shows wire connections being made.
FOR CONTINUOUS RUNS ONLY: For the next fixture in the row, align the open end without an exposed bracket with the open end of the already mounted fixture(s). Slide new fixture onto previously mounted fixture, ensuring the sheet metal at the bottom of the housing is captured by the hook at the bottom of the housing extrusion. Current fixture should be resting on support bracket from previously installed fixture.

Diagram Description: Shows two luminaires being joined together, with one sliding into the other, highlighting the alignment and interlocking mechanism.
Repeat steps 2-4, except the shielded cable attachment. NOTE: Securing fixture to ceiling is not required at joint to already mounted fixture. Internal brackets and previous fixture mounting will support fixture end.

Diagram Description: Shows a fixture being attached to a previously mounted fixture in a continuous run, emphasizing the joiner bracket connection.
Slide joiner bracket capturing joining tabs on each housing and fasten with #8-32 thread cutting screws. Fixture housing will pull together as screws are tightened. Repeat this step so joiner is applied to each side of housing.

Diagram Description: Close-up of the joiner bracket being slid into place and secured with screws, showing how it pulls the housings together.
Complete all wire connections using snap-in harness connector for black, white, green, purple, and pink wires. Any additional connections can be made with provided push-in connectors.

Diagram Description: Shows wire connections being made using snap-in connectors for various colored wires.
Swing Tray back into fixture and re-install screws. Remove protective film from the lift and shift diffusers and install into the fixture. Insert one side (long edge) up into the fixture far enough to get the other side into the fixture.

Diagram Description: Shows the LED tray being swung back into the housing, screws reinstalled, and diffusers being inserted.

NOTE: If lens remains at an angle, use the supplied suction cup near the end of the lens to pull the lens flat and position lens to eliminate any LED visibility.

Warranties and Limitation of Liability

Please refer to www.cooperlighting.com/warranty for our terms and conditions.

	Corelite Bryx Suspended LED Luminaire - Product Specifications and Features Detailed specifications, features, and ordering information for the Corelite Bryx suspended LED luminaire, offering direct/indirect lighting distribution for various applications.
	Corelite Continua and SQ Wall Mount Luminaire Installation Instructions Detailed installation instructions for Corelite Continua and SQ Wall Mount LED Luminaires, covering mounting, wiring, joining, and finishing.
	Corelite Discreet Surface Mount LED Installation Instructions Comprehensive installation guide for the Corelite Discreet Surface Mount LED, covering wiring, mounting, joining fixtures, and maintenance.
	Corelite Divide - DSI LED Surface Mounted Direct/Indirect Lighting Fixture Specifications Comprehensive specifications, features, and ordering guide for the Corelite Divide - DSI LED surface-mounted direct/indirect lighting fixture. Details include WaveStream™ Technology, AccuAim™ optics, lumen packages, energy performance, control systems, and product certifications.
	Corelite Continua SQ4 Suspended LED Installation Instructions Detailed installation instructions for the Corelite Continua SQ4 Suspended LED lighting fixture, covering wiring, assembly, mounting, and maintenance.
	Corelite Divide - DWI LED Wall Mounted Direct/Indirect Lighting Fixture Comprehensive product datasheet for the Corelite Divide - DWI LED Wall Mounted Direct/Indirect lighting fixture, detailing features, specifications, order configurations, photometric data, and advanced control system options.
	Corelite Continua SQ4R Recessed LED Luminaire Detailed specifications and features of the Corelite Continua SQ4R, a 4-inch linear recessed LED luminaire designed for various applications including office, education, healthcare, hospitality, and retail. Highlights include seamless illumination, multiple lens options, tunable white technology (VividTune and BioUp), and integrated sensor systems for advanced lighting control.
	Corelite Iridium i2 WaveStream LED Suspended Luminaire Specification Sheet Detailed specifications for the Corelite Iridium i2 WaveStream LED suspended luminaire, featuring WaveStream technology for superior optical control, energy efficiency, and integrated sensor options for automatic energy savings. Includes construction, electrical, optical, mounting, and ordering information.