Safety Warnings
Risk of Furniture Tip-over
⚠️ WARNING: Children have died from furniture tipover. To reduce the risk of furniture tipover:
- ALWAYS install the anti-tip device provided.
- NEVER allow children to stand, climb, or hang on any drawers, doors, or shelves.
- ALWAYS secure your television with an anchor device.
Assembly Instructions
Read and follow each step of the instruction carefully.
Parts List
Hardware and Tools
- 1x Wrench (190459)
- 5x Screw (100218)
- 8x Screw (109504)
- 6x Dowel/Plug (151707)
- 6x Cam Lock (151708)
- 12x Connector Bracket (10093081)
- 12x Connector Bracket (10093082)
- 8x Dowel (101350)
- 8x Bracket (10117051)
- 16x Cam Lock Screw (10051660)
- 5x Screw (159992)
- 5x Foot/Cap (153552)
- 4x Mounting Bracket (10094472)
- 4x Mounting Bracket (10094447)
- 1x Handle/Bracket (100001)
- 2x Base Plate (10116964)
- 2x Screw (147968)
- 2x Screw (158469)
- 2x Wall Plug (121714)
- 2x Cap (150689)
- 2x Bracket (150688)
- 2x Washer (126916)
Rails
- 4x Rail (10117055)
Assembly Steps
Step 1
Connect the two side panels to the main base panel. Ensure the correct orientation as shown in the close-up diagrams. Use the provided connectors.
Diagram shows two side panels being attached to a long base panel, with arrows indicating insertion points and locking mechanisms.
Step 2
Attach the vertical back support panels to the base structure.
Diagram shows the first set of vertical back support panels being attached to the base.
Step 3
Attach the remaining vertical back support panels.
Diagram shows the second set of vertical back support panels being attached.
Step 4
Place and secure the top panel onto the assembled base and back supports. Use the indicated screws and cam locks.
Diagram shows the top panel being placed on the assembled structure, with arrows indicating alignment and connection points.
Step 5
Insert and tighten 6x cam locks (151708) with screws (151707) to secure the top panel.
Close-up diagram shows a cam lock (151708) being inserted and turned to secure the top panel to the side panels, using screws (151707).
Step 6
Insert 8x dowels (101350) into the pre-drilled holes of the internal shelf dividers.
Diagram shows dowels (101350) being inserted into the internal shelf dividers.
Step 7
Carefully place the internal shelf dividers into their positions within the main structure. Two people may be needed for this step.
Diagram shows two people placing the internal shelf dividers into the main cabinet frame.
Step 8
Attach 5x mounting brackets (100001) to the top panel using screws (100218).
Diagram shows mounting brackets (100001) being screwed onto the top surface of the cabinet.
Step 9
Attach 5x feet/caps (153552) to the underside of the base panel using 5x screws (159992).
Diagram shows feet/caps (153552) being attached to the bottom of the cabinet using screws (159992).
Step 10
Attach 5x feet/caps (153552) to the underside of the base panel using 5x screws (159992).
Diagram shows feet/caps (153552) being attached to the bottom of the cabinet using screws (159992).
Step 11
Attach 12x runner brackets (10093081 and 10093082) to the inside vertical panels of the cabinet.
Diagram shows runner brackets (10093081, 10093082) being attached to the inner sides of the cabinet sections.
Step 12
Attach 4x rails (10117055) and 4x corresponding runner parts (10117051) to the cabinet structure. Follow the numbered sequence (1-4) for proper alignment.
Diagram shows rails (10117055) and runner parts (10117051) being assembled and attached to the cabinet, with numbered steps indicating the sequence.
Step 13
Insert the assembled rails into the cabinet compartments. Arrows indicate insertion direction.
Diagram shows the assembled rails being slid into the cabinet compartments.
Step 14
Attach 4x runner parts (10117051) to the cabinet structure.
Diagram shows additional runner parts (10117051) being attached to the cabinet.
Step 15
Secure the runners by inserting 4x screws (109504).
Diagram shows screws (109504) being used to secure the runners.
Step 16
Attach 2x bracket components (150688) to the back of the cabinet.
Diagram shows bracket components (150688) being attached to the rear of the cabinet.
Step 17
Attach 2x cap components (150689) to the back of the cabinet.
Diagram shows cap components (150689) being attached to the rear of the cabinet.
Step 18
Insert the sliding door mechanisms into the corresponding slots on the cabinet. The diagram shows the correct orientation and action.
Diagram shows sliding door mechanisms being inserted into slots on the cabinet.
Step 19
Attach the door guides to the cabinet structure.
Diagram shows door guides being attached to the cabinet.
Step 20
Secure the top of the cabinet using 5x screws (190459) with the provided tool (190459).
Diagram shows screws (190459) being tightened into the top of the cabinet using the tool (190459).
Step 21
Attach 2x hinge/bracket components to the cabinet for the doors.
Diagram shows hinge/bracket components being attached to the cabinet for door installation.
Step 22
Ensure all parts are correctly aligned. The 'X' marks indicate alignment points.
Diagram shows the cabinet structure with alignment marks, indicating a final check.
Wall Mounting Instructions
General Guidance
The screw(s) and plug(s) supplied can be used with most solid (A) and hollow (B) walls. For solid wood (C) use the screw(s) without plug(s). If you are uncertain, seek professional advice.
Mounting Type A: Solid Walls
Drill a Ø 8 mm (5/16") hole to a depth of 70 mm (2 3/4"). Insert wall plug (121714) and then screw.
Mounting Type B: Hollow Walls
Drill a Ø 8 mm (5/16") hole to a depth of approximately 30 mm (1 1/4"). Insert wall plug (121714) and then screw.
Mounting Type C: Solid Wood
Drill a Ø 3 mm (1/8") hole to a depth of approximately 30 mm (1 1/4"). Use screw directly without a plug.
Note: QR codes link to www.IKEA.com/secure-it and www.IKEA.cn/secure-it for more information on securing furniture.
Final Assembly & Door Installation
Step 23
Attach 2x back panel supports (10116964) to the back of the cabinet using screws (147968 and 158469) and washers (126916). Ensure a 'Click!' sound indicates secure attachment.
Diagram shows back panel supports (10116964), screws (147968, 158469), and washers (126916) being attached to the back of the cabinet. A close-up shows the 'Click!' mechanism.
Step 24
Insert 16x cam lock screws (10051660) into the designated holes for internal shelves.
Diagram shows cam lock screws (10051660) being inserted into the internal divisions of the cabinet.
Step 25
Attach 4x mounting plates (10094472) to the inside of the cabinet.
Diagram shows mounting plates (10094472) being attached to the inner sides of the cabinet sections.
Step 26
Attach 4x shelf support brackets (10094447) to the mounting plates.
Diagram shows shelf support brackets (10094447) being attached to the mounting plates.
Step 27
Install sliding doors. Follow the numbered sequence (1-4) and ensure they click into place.
Diagram shows sliding doors being fitted onto the runners, with a numbered sequence and a close-up showing the locking mechanism engaging with a 'Click!' sound.
Step 28
Attach the doors to the cabinet hinges. The diagram shows the correct alignment and connection method.
Diagram shows a door being attached to the cabinet hinges.
Step 29
Attach the second door to the cabinet hinges. Ensure a 'Click!' sound indicates secure attachment.
Diagram shows the second door being attached to the cabinet hinges, with a close-up showing the locking mechanism engaging with a 'Click!' sound.
Step 30
Adjust the doors using the mechanism shown (4x adjustment points). Turn the adjustment screw to set doors to 'Min' or 'Max' position for proper alignment and closure.
Diagram shows the adjustment mechanism for the doors, with indicators for 'Min' and 'Max' settings.
Product Overview
The TONSTAD TV bench is a long, low cabinet designed to hold televisions and media equipment. It features two sliding doors that provide access to internal shelving compartments. The design emphasizes clean lines and functionality, typical of IKEA products.
