Safety Precautions
Prior to use, read the safety precautions carefully to ensure proper use. The precautions listed here are described under classification of Warnings and Cautions, and are intended to prevent harm or damages to users and other persons. All of these precautions are critical in terms of safety. Follow them at all times.
Graphic symbol indications: Indicates content that could lead to death or injury if handled incorrectly.
? Disassembly prohibited.
- Do not disassemble, repair, or modify. Doing so can cause fire, electric shock, or injury.
- Repair by persons other than trained repair technicians can be dangerous.
- Warning: To reduce the risk of fire or electric shock, do not use this product with any solid-state speed control device.
ℹ Product use.
- Use on a level, stable floor. Placing product on uneven and unstable floors can cause the product to fall over, leading to injury or damage to property in the vicinity of the product.
- Place the product in locations where it will not get entangled in curtains or hoisting strings, etc. Failing to do so can cause damage to articles near the product.
- Always grasp the power plug to unplug it, do not unplug it by pulling on the power cord. Pulling on the power cord can damage it, which can cause fire or electric shock.
- Always unplug the power plug from the electrical outlet when the product will be unused for extended periods of time. Failing to do so can lead to fire or electric shock caused by short-circuits due to reduced insulation.
- This product employs overload protection (fuse). A blown fuse indicates an overload or a short-circuit. If the fuse blows, unplug the product from the outlet. Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the product. If the replacement fuse blows, a short-circuit occurred and the product should be discarded or returned to IRIS USA, Inc. for inspection and/or repair.
ℹ Unplug.
- Unplug the power plug from the electrical outlet when performing maintenance, inspecting, or moving the product.
- This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.
- Grasp the plug and remove from the receptacle or other outlet device. Do not unplug by pulling on the cord.
ℹ Use power plugs and power cords correctly.
- Failing to do so can cause fire or electric shock due to short-circuits.
- Insert the power plug securely all the way into the electrical outlet.
- Regularly remove dust from the power plug. When dust is allowed to build up, insulation is hampered due to moisture, which can cause fire or electric shock.
- Use only 120 V~. Other current/voltage can cause fires.
- Do not use if the power cord or the power plug is damaged, or if the power plug is loose when plugged into the electrical outlet. Doing so can cause fire or electric shock due to short-circuit.
- Do not run the cord under carpeting. Do not cover the cord with throw rugs, runners, or similar coverings. Do not run the cord under furniture or appliances. Arrange the cord away from high traffic areas and where it will be tripped over.
- Do not operate any fan with a damaged cord or plug. Discard fan or return to an authorized service facility for examination and/or repair.
? Do not damage the power cord.
- Damaging, modifying, forcefully bending, pulling, twisting, putting heavy objects, or pinching can damage the power cord, which can cause fire or electric shock.
- Do not use if the power cord is bundled up. Doing so can cause fires. Always extend the cord out before using.
- Do not pull on the power cord when carrying or storing the product. Pulling on the power cord can cause fire or electric shock.
- To avoid electric shock, fire or hazard, if the power cord is damaged, discard the fan or return it to IRIS USA, Inc. for inspection/or replacement.
⚠ Abnormalities and malfunctions can cause smoke, fire, or electric shock.
Stop use immediately, cut power, and unplug from the electrical outlet when abnormalities or malfunctions occur.
Examples of abnormalities:
- Abnormal sounds or odors.
- Power plug or power cord become abnormally hot.
- Loss of power, etc. when power cord is moved.
- The product periodically stops during operation.
- Tingling sensation from electric current felt when the product is touched.
- Stop use and contact IRIS USA, Inc. customer service at 1-800-320-4747.
⚠ Avoid fire hazards.
- Do not spray with insecticides, hair sprays, or lubrication oils, etc.
- Do not use near flammable substances (kerosene, gasoline, paint thinner, etc.), objects that have flames (cigarettes, incense, etc.) or combustible materials. Can cause fires.
- Do not use the product with air flow pointed at a combustible appliance such as a heater. Doing so can cause incomplete combustion or scatter flames, which can cause carbon monoxide poisoning and fire.
? Wet hands prohibited.
- Do not unplug power plug when hands are wet.
? Do not use the product outdoors.
- Do not use in the vicinity of objects that obstruct the flow of air.
- Do not operate while covered or blocked with cloth, paper, or plastic bags, etc.
- Do not use in locations where there is a lot of dirt or dust. This can cause short-circuit or fire.
- Do not use in rooms with high humidity levels such as bathrooms.
- Do not get the unit wet, or put the unit in water. Getting the product wet can cause fire or electric shock.
⚠ If handled incorrectly, contents can lead to personal injury or physical damage.
- Keep out of reach of children and infants.
- Do not climb on or tip the product over. Doing so may lead to injury or electric shock.
- Do not drag the product when moving it. Dragging product can damage carpet and floors.
- Do not point air flow directly at your body. It generates a very strong air flow.
- Be especially mindful not to allow children or elderly people near product. Being near the product can be harmful to their physical condition and to their health.
- Air blowing directly on plants may be harmful.
- Do not operate without attaching the vane or the cover. Doing so can cause injury, electric shock, or fire.
- Do not strike the unit forcefully. Doing so can cause the product to malfunction, leading to fire or electric shock.
ℹ User servicing instructions.
- If the fuse on your fan has blown, grasp the plug and remove it from the outlet. Do not pull the cord to unplug. To open, slide the fuse cover towards the prongs of the plug. Carefully remove the old fuse and snap the replacement fuse into place. To reduce the risk of fire, only replace the fuse with another fuse of the proper rating (2.5 A, 125 V~). Slide the fuse door back into place to close. Discard the blown fuse. The plug should now be ready for normal use.
- To reduce the risk of fire, do not replace the attachment plug if it is damaged. Only the fuse should be replaced. Discard the product if the attached plug is damaged.
- If you need further information on how or when to replace the fuse in plug, contact IRIS USA, Inc. customer service at 1-800-320-4747.
Placement
Placement Guidelines
- Place the product on a level floor or table free of any obstructions.
- Place the product in locations where it will not come in contact with direct sunlight, or hot air from air conditioning or heating appliances. Such contact can cause the product to deform, change color, or malfunction.
- Do not place the product near the radio or TV. The product may cause noise on radio and affect the TV signal.
Usage Scenarios
The circulator fan can be used in various ways to optimize air circulation:
- Use with Air Conditioner: Placing the product in front of an air conditioner helps circulate cold air accumulated below, creating better airflow and cooling. (Depiction: Fan facing A/C unit, circulating air across a room.)
- Use with a Heater: Sending airflow towards a corner of the room where an A/C source is, or towards accumulated warm air above, helps warm feet. (Depiction: Fan facing a heater, circulating warm air downwards.)
- Circulation: Directing airflow toward the ceiling reduces room air temperature variations. (Depiction: Fan pointing upwards, circulating air throughout a room.)
- Ventilation: Placing the product by a window or an open door draws outside air in and sends in-room air out. (Depiction: Fan placed by a window, circulating air in/out.)
- Two-room Circulation: Placing the product in an open doorway circulates air between two rooms. (Depiction: Fan placed in a doorway between two rooms, circulating air.)
- Drying Laundry: Hanging laundry directly in the path of the airflow helps it dry quicker. Do not place the fan underneath dripping clothes as water droplets on the product may cause electric shock or short-circuiting. (Depiction: Fan blowing air towards hanging clothes.)
Parts
Front View
The front of the circulator fan includes:
- Front guard: The protective mesh at the front.
- Vane: The fan blades inside the guard.
- Control panel: Located on the base, used for operation.
- Main body: The primary housing of the fan.
- Swivel base: The base allowing for horizontal oscillation.
Back View
The back of the circulator fan includes:
- Rear guard: The protective mesh at the back.
- Handle: For carrying the unit.
- Motor (Internal): The internal motor assembly.
- Power plug: The electrical plug.
- Power cord: The electrical cord connecting to the power plug.
Control Panel Description
The control panel features a knob with two main functions:
- AIR FLOW (Left side of knob): Turning the knob to the left selects the desired air flow strength (OFF, I, II, III). This mode operates without oscillation.
- OSCILLATE (Right side of knob): Turning the knob to the right selects the desired air flow strength with left and right oscillation (OFF, I, II, III).
How to Use
Place the Product
Place the product upright on a stable surface and insert the power plug into the electrical outlet.
Select the Preferred Air Flow Strength
Turn the knob to the left to select the desired air flow strength (no oscillation). The settings are typically OFF, I, II, III, indicating increasing fan speed.
Stop the Product
Turn the knob to OFF to stop operation.
Select Oscillation
The horizontal oscillation cannot be done manually. Use the knob to initiate the horizontal oscillation of the product. Forcibly changing the horizontal direction will damage the product.
- Horizontal Oscillation: Turn the knob to the right to select the desired air flow strength with left and right oscillation. The settings are typically OFF, I, II, III, indicating increasing fan speed with oscillation.
- Vertical Adjustment:
- The PCF-HE18 can be adjusted in 7 positions from -20° to 90°.
- The PCF-HE15 can be adjusted in 6 positions from -22.5° to 90°.
Cleaning and Maintenance
⚠ Caution
Always turn off the power and unplug the power plug from the electrical outlet when cleaning the product. Use caution, the motor will be hot immediately after use. Confirm the motor has cooled before cleaning the product.
Do not use paint thinner, alcohol, benzene, alkaline detergent, or bleach, etc. when cleaning the product. Using such substances can cause damage, malfunctions, or changes in color, shape, and quality.
Using the product in dusty condition can cause it to malfunction. Check and clean the product regularly.
Internal Cleaning
- Remove the front guard.
Unscrew the 3 screws from the back cover and remove the front guard. *Make sure that all the screws are removed. (Depiction: Screws indicated on the back cover, and the front guard detaching.)
- Remove debris using a vacuum cleaner. Wipe off debris that cannot be removed by vacuuming using a soft cloth. (Depiction: Vacuum cleaner removing dust from the fan interior.)
- Assemble the front guard.
Assemble the front guard by tightening the screws. (Depiction: Reattaching the front guard with screws.)
External Cleaning
- Wipe lightly using a soft cloth.
- For hard to remove dirt, wipe using a cloth containing a diluted neutral detergent.
How to Store
When the product is not used for an extended period of time, cover the unit with a plastic bag, etc., and then store it in a dry location away from direct sunlight.
Troubleshooting
Before making repairs, read the following content carefully to fix common problems.
| PROBLEM | POSSIBLE CAUSES | SOLUTION |
|---|---|---|
| Will not operate | Power plug is not securely plugged into the electrical outlet | Plug the power plug securely into the electrical outlet. |
| Product makes loud noise while operating | The product is placed on an uneven surface | Place the product on a level, stable surface. |
| The front guard is not securely attached | Attach the front guard properly. | |
| Weak air flow | Dust has accumulated | Clean to remove the dust. |
| Product makes loud noise while oscillating | During oscillation, motor (internal) sounds will increase | This is normal. |
Problems that could not be resolved: Contact the dealer of purchase or IRIS USA, Inc. Customer Service.
⚠ Warning:
Do not disassemble, repair or modify the product yourself. Any other servicing should be performed by any authorized service representative.
Product used over long periods of time
If any of the following problems occur due to use over long periods of time, cut power immediately, unplug from the electrical outlet, and contact IRIS USA, Inc. customer service at 1-800-320-4747.
- There is no response when power is turned on.
- Product makes a strange noise when operating.
- While turning, the vane changes speed irregularly.
- Power cord is bent or damaged.
- Power turns on and off when power cord is touched.
- Product gives off a burnt smell.
⚠ Warning:
Various factors can have an impact on the product degradation and malfunction. If abnormalities like those listed above occur even when the product has not been used for the displayed standard period of use, stop use immediately and contact IRIS USA, Inc. customer service at 1-800-320-4747.
Specifications
| MODEL | SPECIFICATIONS |
|---|---|
| RATED VOLTAGE | 120 V~ |
| RATED FREQUENCY | 60 Hz |
| RATED CURRENT | PCF-HE15: 0.4 A PCF-HE18: 0.8 A |
| PRODUCT SIZE (NOT INCLUDING THE POWER CORD) | PCF-HE15: 9.49 x 6.97 x 11.26 in/241 x 177 x 286 mm PCF-HE18: 11.46 x 7.52 x 12.2 in/291 x 191 x 310 mm |
| PRODUCT WEIGHT (APPROXIMATELY) | PCF-HE15: 3.53 lbs/1.6 kg PCF-HE18: 4.63 lbs/2.1 kg |
| APPLICABLE AREA COVERAGE (APPROXIMATELY) | PCF-HE15: 139.5 ft²/12.96 m² PCF-HE18: 244.13 ft²/22.68 m² |
| POWER CORD LENGTH (APPROXIMATELY) | 70.9 in/1.8 m |
*Specifications are subject to change without prior notice.
Manufacturer 1-Year Warranty
The Manufacturer Warrants
IRIS USA, Inc. products are to be free from defects in material and workmanship under normal non-commercial, household use, when operated and cared for in accordance with the Manufacturer's written instructions provided.
The 1-Year Warranty ("Warranty") Does Not Cover
Any damage caused by accident, misuse, or abuse, including without limitation, damage caused by use in a humid area, improper cleaning, neglect, alteration, fire, theft, non-recommended temperature use and does not apply to minor imperfections, scratches, stains, discoloration, surface markings as a result of shipping or other damage to external or internal surfaces which does not impair the utility and/or functionality of the product.
To Obtain Service
If service should be necessary, you should contact IRIS USA, Inc. Customer Service ("Customer Service") at 1-800-320-4747. You may then return the properly packaged product(s), (using adequate packing and shipping material to prevent damage in transit), with postage prepaid along with name, address, telephone number, model number, and proof of date of purchase (a copy of the receipt) and a detailed description of the claimed defect. This warranty shall not cover any damage incurred to the products during transit to Customer Service. You shall have the obligation and responsibility to: pay for all services and parts not covered by the warranty.
Manufacturer's Obligation
The Warranty may not be altered, expanded, extended, revised or varied except by written instrument executed by the Manufacturer.
THE MANUFACTURER'S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT OF THE DEFECTIVE PRODUCT(S) AT THE MANUFACTURER'S SOLE AND EXCLUSIVE OPTION. THE MANUFACTURER WILL REPLACE ANY ITEM FOUND TO BE DEFECTIVE IN MATERIAL OR WORKMANSHIP WITH THE MOST COMPARABLE CURRENT ITEM. IRIS USA, INC. DOES NOT ACCEPT SPECIAL REQUESTS, NOR DO WE HAVE THE ABILITY TO UPGRADE IN EXCHANGE FOR MONEY. THE MANUFACTURER SHALL NOT BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES, WHETHER DIRECT OR INDIRECT. THE WARRANTIES SET FORTH HEREIN ARE EXCLUSIVE AND NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR USE ARE MADE WITH RESPECT TO THE PRODUCTS.
Some states do not allow the exclusion of limitation of incidental or consequential damages, so the above limitation exclusions may not apply. This Warranty gives specific legal rights, and there may also be other rights which vary from state to state.
Discontinued Item Returned
If the item returned is discontinued and is no longer available, IRIS USA, Inc. will automatically replace your item with the most comparable item currently manufactured.
Attn: Customer Service (Returns Department)
IRIS USA, Inc.
13423 West Cactus Road
Surprise, AZ 85379
©2020 IRIS USA, Inc. All rights reserved.
