WOOZOO® Globe Fan

Safety Precautions

Prior to use, please read the safety precautions carefully to ensure proper use. The precautions listed here are described under classification of Warnings and Cautions, and are intended to prevent harm or damages to users and other persons. All of these precautions are critical in terms of safety. Please follow them at all times.

Graphic Symbol Indications: Indicates content that could lead to death or injury if handled incorrectly.

• ⚠️ CAUTION
• ? PROHIBITED
• ❗ INSTRUCTIONS THAT MUST BE FOLLOWED

Disassembly Prohibited

• Do not disassemble, repair, or modify. Doing so can cause fire, electric shock, or injury.
• Repair by persons other than trained repair technicians can be dangerous.
• Warning: To reduce the risk of fire or electric shock, do not use this product with any solid-state speed control device.

Product Use

• For household use only. Do not use for commercial use. Do not use for anything other than the intended purposes. Doing so could cause the product to malfunction or cause fire.
• Do not use the product near radio or televisions. Doing so may interfere with radio or television signals.
• Do not use in places exposed to direct sunlight or heating devices. Doing so may cause deformation, color change, or product malfunctions.
• Use on a level, stable surface. Placing product on uneven and unstable surface can cause the product to fall over, leading to injury or damage to property in the vicinity of the product.
• Place the product in locations where it will not get entangled in curtains or hoisting strings, etc. Failing to do so can cause damage to articles near the product.
• Always grasp the power plug to unplug it, do not unplug it by pulling on the power cord. Pulling on the power cord can damage it, which can cause fire or electric shock.
• Always unplug the power plug from the electric socket when the product will be unused for extended periods of time. Failing to do so can lead to fire or electric shock caused by short-circuits due to reduced insulation.
• This product employs overload protection (fuse). A blown fuse indicates an overload or a short-circuit. If the fuse blows, unplug the product from the outlet. Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the product. If the replacement fuse blows, a short-circuit may be present and the product should be discarded or returned to IRIS USA, Inc. for inspection and/or repair.
• Do not run the cord under carpeting. Do not cover the cord with throw rugs, runners, or similar coverings. Do not run the cord under furniture or appliances. Arrange the cord away from high traffic areas and where it will not be tripped over.
• Please dispose of product and packaging materials according to proper government regulations.

Remote Use

• WARNING: Chemical Burn Hazard. Do not allow batteries to be swallowed.
• This product contains a button/coin cell battery. If the button/coin cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
• Please pay attention to the polarity symbols of the remote battery. Please ensure the battery is inserted according to the correct positive (+) and negative (-) markings.
• Remove the remote battery when the product will not be used for extended periods of time. Not doing so may cause fire or injury, or damage to the surroundings from the battery rupturing and leaking.

• In case of battery liquid leaking, wipe down the battery case and insert a new battery. If the battery liquid gets onto the skin, please wash thoroughly.
• Do not disassemble, repair, or modify. Doing so may cause damage to skin and clothes.
• Do not carry or store the remote alongside small metal objects. Doing so may cause fire or injury from the battery rupturing and leaking.
• Please use only the manufacturer recommended battery. Use of any other battery may cause risk of fire or injury, or damage to the surroundings from the battery rupturing and leaking.

Unplug

• Unplug the power plug from the electric socket when performing maintenance, inspecting, or moving the product.
• This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.
• Grasp the adapter plug and remove from the receptacle or other outlet device. Do not unplug by pulling on the cord.

Use Power Plugs and Power Cords Correctly

• Failing to do so can cause fire or electric shock due to short-circuits.
• Insert the power plug securely all the way into the electric socket.
• Regularly remove dust from the power plug. When dust is allowed to build up, insulation is hampered due to moisture, which can cause fire or electric shock.
• Use only 100-240V~. Other current/voltage can cause fires.
• Do not use if the power cord or the power plug is damaged, or if the power plug is loose when plugged into the electric socket. Doing so can cause fire or electric shock due to short-circuit.
• Do not operate any fan with a damaged cord or plug. Discard fan or return to an authorized service facility for examination and/or repair.
• Please use only the manufacturer recommended adapter. Use of any other adapter may cause risk of fire or injury.

Do Not Damage the Power Cord or Adapter

• Damaging, modifying, forcefully bending, pulling, twisting, putting heavy objects, or pinching can damage the power cord, which can cause fire or electric shock.
• Do not use if the power cord is bundled up. Doing so can cause fires. Always extend the cord out before using.
• Do not pull on the power cord when carrying or storing the product. Pulling on the power cord can cause fire or electric shock.

Abnormalities and Malfunctions

Abnormalities and malfunctions can cause smoke, fire, or electric shock. Stop use immediately, cut power, and unplug from the electric socket when abnormalities or malfunctions occur.

Examples of Abnormalities

• Abnormal sounds or odors.
• Power plug or power cord become abnormally hot.
• Loss of power, etc. when power cord is moved.
• The product periodically stops during operation.
• Tingling sensation from electric current felt when the product is touched.

Stop use and contact IRIS USA, Inc. customer service at 1-800-320-4747.

Placement

Place the product on a level floor or table free of any obstructions.

Place the product in locations where it will not come in contact with direct sunlight, or hot air from air conditioning or heating appliances. Such contact can cause the product to deform, change color, or malfunction.

Do not place the product near the radio or TV. The product may cause noise on radio and affect the TV signal.

Parts

Front View

• Vane
• Front guard
• Control panel
• Base
• Remote receiver

Back View

• Handle
• Rear guard
• Motor
• Adapter
• Power cord

Control Panel

The control panel includes:

• Power button
• Delayed start button and indicator light
• Timer button and indicator light
• Air flow strength buttons and indicator light (left/right arrows)
• Mode button
• Mode indicator lights
• Horizontal oscillation button and indicator light
• Vertical oscillation button and indicator light

Remote Control

The remote control allows operation from a distance. It includes:

• Power button: Turns the product on or off.
• Delayed start button: Sets a timer for the product to start later.
• Timer button: Sets the desired run time for the product.
• Air flow strength buttons (arrows): Adjust the fan speed.
• Oscillation buttons (Horizontal, Vertical): Control the oscillation direction and range.
• Mode button: Selects the operating mode (Continuous, Breeze, Focused Oscillation).

Changing Out The Battery

Replace the battery with a CR2025 when the product responds slowly or not at all. The process involves pulling out the battery holder, replacing the battery (observing polarity), and reinserting the holder.

Caution: Improper handling of the battery can lead to rupture, leaking liquid, and damage to surroundings.

Usage Instructions

How to Use

1. Place the Product: Place the product upright on a stable surface. Insert the charger plug into the product, then insert the adapter plug into the electrical outlet. The product will beep when buttons are pressed.
2. Start the Product: Press the power button to turn the product on. It will start running at the last setting used if the power plug has not been pulled out. The product can also be turned on using the power button on the remote control.
3. Select the Operating Mode: Press the Mode button to cycle through the modes:
   • Continuous: Product runs with a continuous air flow at the chosen air flow strength.
   • Breeze: Replicates breeze patterns by changing the strength of the air flow.
   • Focused Oscillation: The product operates at high intensity, oscillating up to 60 degrees then down to 45 degrees. After settling at 45 degrees, it oscillates left and right within a 30-degree range. Vertical and horizontal oscillation indicators will illuminate accordingly. In this mode, horizontal oscillation, vertical oscillation, and air flow strength cannot be adjusted.
   Modes can also be selected via the remote control.
4. Select the Preferred Air Flow Strength: Press the air flow strength buttons (left/right arrows) to adjust the fan speed. Continuous mode offers 10 strength settings; Natural Breeze mode offers 3 settings. Holding the button in continuous mode will cycle through intensities until released.
5. Set Delayed Start Time: This timer can only be set when the product is off but plugged in, or after the timer has been set. It cannot be set while the product is running unless a run time has already been chosen. Pressing the delayed start button cycles through options: 2 hours, 4 hours, 8 hours, or off. The indicator light will change while the timer is active.
6. Start Timer: Pressing the timer button sets the desired run time. Options are 2 hours, 4 hours, 8 hours, or off. The indicator light changes as the timer counts down. When time runs out, the product will turn off. If oscillating, the product will not reset to the front position when the timer ends.
7. Set Combined Delayed Start Time and Timer: To set a specific start and stop time, first set the delayed start time, then set the run time using the timer button. The process requires setting the delayed start time when the product is off and plugged in. The indicator lights will guide the process.
8. Stop the Product: Press the power button during operation to turn the product off. The product will beep before powering down. If turned off during oscillation, it will stop facing forward. Oscillation indicator lights will blink until the product returns to the forward position.
9. Select Oscillation: Use the oscillation buttons (Horizontal, Vertical) on the remote or unit to control oscillation. Horizontal oscillation can be set to 60°, 90°, or 120°, or turned off. Vertical oscillation can be activated or deactivated. Vertical angle can be manually adjusted up to 60 degrees. Forcible manual adjustment may damage the product.
10. Adjust the Brightness of the Indicator Lights: Hold the Mode button for at least 2 seconds while the product is running to adjust brightness. Hold again for 2 seconds to return to original brightness. Brightness settings are saved but reset to original if the product is unplugged. Remote control cannot adjust brightness.

Cleaning and Maintenance

Caution: Always turn off the power and unplug the power plug from the electric socket when cleaning the product. Use caution, the motor will be hot immediately after use. Confirm the motor has cooled before cleaning the product.

Do not use paint thinner, alcohol, benzene, alkaline detergent, or bleach, etc. Using such substances can cause damage, malfunctions, or changes in color, shape, and quality.

Using the product in dusty conditions can cause it to malfunction. Check and clean the product regularly.

Internal Cleaning

1. Unscrew the screws from the back cover of the fan. Press in and disengage the 4 claws on the top and bottom of the front guard, and then remove the front guard by pulling it toward you.
2. Remove debris using a vacuum cleaner. Wipe off debris that cannot be removed by vacuuming using a soft cloth.
3. Align claws on the top and bottom of the front guard with the guides on the back of the guard, align the handle on the back with the groove on the top of the front guard, and press until it snaps into place. Reattach screws.

External Cleaning

• Wipe lightly using a soft cloth.
• For hard-to-remove dirt, wipe using a cloth containing a diluted neutral detergent.

Troubleshooting

Before making repairs, please read the following content carefully to fix common problems.

Problems that could not be resolved. Please contact the dealer of purchase or IRIS USA, Inc. Customer Service.

Warning: Do not disassemble, repair or modify the product yourself. Any other servicing should be performed by any authorized service representative.

Product Used Over Long Periods of Time

If any of the following problems occur due to use over long periods of time, cut power immediately, unplug from the electric socket, and contact IRIS USA, Inc. customer service at 1-800-320-4747.

• There is no response when power is turned on.
• Product makes a strange noise when operating.
• While turning, the vane changes speed irregularly.
• Power cord is bent or damaged.
• Power turns on and off when power cord is touched.
• Product gives off a burnt smell.

Attention Various factors can have an impact on the product degradation and malfunction. If abnormalities like those listed above occur even when the product has not been used for the displayed standard period of use, stop use immediately and contact IRIS USA, Inc. customer service at 1-800-320-4747.

Specifications

*Specifications are subject to change without prior notice.

Manufacturer 1-Year Warranty

The Manufacturer Warrants

Your IRIS USA, Inc. products are to be free from defects in material and workmanship under normal non-commercial, household use, when operated and cared for in accordance with the Manufacturer's written instructions provided.

The 1-Year Warranty ("Warranty") Does Not Cover

Any damage caused by accident, misuse, or abuse, including without limitation, damage caused by use in a humid area, improper cleaning, neglect, alteration, fire, theft, non-recommended temperature use and does not apply to minor imperfections, scratches, stains, discoloration, surface markings as a result of shipping or other damage to external or internal surfaces which does not impair the utility and/or functionality of the product.

To Obtain Service

If service should be necessary, you should contact IRIS USA, Inc. Customer Service ("Customer Service") at 1-800-320-4747. You may then return the properly packaged product(s), (using adequate packing and shipping material to prevent damage in transit), with postage prepaid along with name, address, telephone number, model number, and proof of date of purchase (a copy of the receipt) and a detailed description of the claimed defect. This warranty shall not cover any damage incurred to the products during transit to Customer Service. You shall have the obligation and responsibility to: pay for all services and parts not covered by the warranty.

Manufacturer's Obligation

The Warranty may not be altered, expanded, extended, revised or varied except by written instrument executed by the Manufacturer.

THE MANUFACTURER'S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT OF THE DEFECTIVE PRODUCT(S) AT THE MANUFACTURER'S SOLE AND EXCLUSIVE OPTION. THE MANUFACTURER WILL REPLACE ANY ITEM FOUND TO BE DEFECTIVE IN MATERIAL OR WORKMANSHIP WITH THE MOST COMPARABLE CURRENT ITEM. IRIS USA, INC. DOES NOT ACCEPT SPECIAL REQUESTS, NOR DO WE HAVE THE ABILITY TO UPGRADE IN EXCHANGE FOR MONEY. THE MANUFACTURER SHALL NOT BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES, WHETHER DIRECT OR INDIRECT. THE WARRANTIES SET FORTH HEREIN ARE EXCLUSIVE AND NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR USE ARE MADE WITH RESPECT TO THE PRODUCTS.

Some states do not allow the exclusion of limitation of incidental or consequential damages, so the above limitation exclusions may not apply. This Warranty gives specific legal rights, and there may also be other rights which vary from state to state.

Discontinued Item Returned

If the item returned is discontinued and is no longer available, IRIS USA, Inc. will automatically replace your item with the most comparable item currently manufactured.

Attn: Customer Service (Returns Department)
IRIS USA, Inc.
13423 West Cactus Road
Surprise, AZ 85379

©2019 IRIS USA, Inc. All rights reserved.