SKANSNÄS Chair Assembly Instructions

Step 1: Preparation

Lay out all parts on a soft, protective surface, such as a rug, to prevent scratches. Ensure you have the correct tools: a Phillips head screwdriver and the included Allen key. Do not use a power drill for assembly. ℹ️

Diagram Description: Visuals show a person with tools (screwdriver, Allen key), parts laid on a rug, a warning symbol for incorrect assembly, and a person contemplating parts before contacting IKEA.

Step 2: Assemble Base Frame

Take two side frames. Insert protective pads (I) onto the bottom of the legs. Insert two connectors (B) into the designated holes on the side frames.

Attach the crossbars to the side frames using four screws (F) and the Allen key (A). A close-up shows the screw being inserted and tightened.

Diagram Description: Two side frames are shown upright. Protective pads are applied to the bottom. Connectors are inserted. The base frame is then assembled by attaching crossbars to the side frames with screws and an Allen key.

Step 3: Attach Circular Fittings

Take a long bar. Insert a nut into a circular fitting (G). Attach this assembly to the base frame using a screw (G).

Diagram Description: A long bar is shown with a nut being inserted into a circular fitting. This assembly is then attached to the base frame using a screw.

Step 4: Install Seat Support Rods

Insert a rod (A) through a hole in the main chair frame. A close-up shows the rod being inserted. A STOP sign indicates not to use a power drill. ?

Diagram Description: The main chair frame is shown. A person inserts a rod through a hole in the frame. A warning symbol advises against using a power drill.

Step 5: Attach Seat Base Connectors

Take another long bar. Insert a nut into a circular fitting (G). Attach this assembly to the frame.

Diagram Description: A long bar is shown with a nut being inserted into a circular fitting. This assembly is attached to the frame.

Step 6: Secure Seat Base

Insert a screw (C) into a hole on the chair frame. ? Do not use a power drill.

Diagram Description: The chair frame is shown. A person inserts a screw into a hole. A warning symbol advises against using a power drill.

Step 7: Prepare for Backrest Attachment

Insert two circular fittings (G) into the designated holes on the chair frame.

Diagram Description: The chair frame is shown. Two circular fittings are being inserted into holes.

Step 8: Attach Side Supports

Attach two side supports to the main frame.

Diagram Description: Two side supports are shown being attached to the main chair frame.

Step 9: Attach Backrest

Attach the backrest to the chair frame using four screws (E). Ensure correct alignment.

Diagram Description: The backrest is being attached to the chair frame using screws. Close-ups show how to align and insert the screws.

Step 10: Secure Backrest

Secure the backrest using the circular fittings (G). A "Click!" sound indicates proper locking. ?

Diagram Description: The backrest is being secured with circular fittings. A close-up shows the locking mechanism engaging with a "Click!" sound.

Step 11: Attach Seat Base

Turn the chair upside down. Attach the seat base to the frame using four screws (A) and the Allen key (A). ? Do not use a power drill.

Diagram Description: The chair is shown upside down. The seat base is being attached to the frame using screws and an Allen key. A warning symbol advises against using a power drill.

Step 12: Final Seat Attachment

Place the chair on a table for easier access. Use two screws (D) to attach the seat base.

Diagram Description: The chair is placed on a table. Screws are used to attach the seat base.

Step 13: Attach Seat Cushion

Attach the seat cushion using three L-brackets (H) and three screws (E).

Diagram Description: The seat cushion is being attached to the chair frame using L-brackets and screws.

Step 14: Finalize Seat Cushion

Lower the seat cushion into its final position. Secure the seat cushion using two screws (C).

Diagram Description: The seat cushion is lowered into place and then secured with screws.

Step 15: Final Check

Ensure all screws are tightened and the chair is stable. Your SKANSNÄS chair is now assembled.

Diagram Description: Shows the fully assembled SKANSNÄS chair.