Blackview AirBuds 100
USER GUIDE
PRODUCT INTRODUCTION
The Blackview AirBuds 100 feature an Earbuds LED indicator, a touch control surface, and a charging case with an LED digital display and a USB-C charging port.
Diagram Description: The diagram shows a pair of wireless earbuds and their charging case. The earbuds have an LED indicator light. The charging case has a digital display showing "188" and a USB-C charging port.
Connect
Pairing:
- Take the earphones out of the charging box; they will turn on automatically.
- Open your phone's Bluetooth settings and select "AirBuds 100" to pair.
Reset:
- Delete the "AirBuds 100" pairing information from your phone's Bluetooth settings.
- Place the earbuds back into the charging case.
- Take the earbuds out of the charging case and wait for 20 seconds.
(If the above operation does not work, please try again)
Factory settings: In pairing state, double-click and long press for 5 seconds.
Operation
The touch controls on the earbuds allow for various functions:
- Play / Pause: Click the touch control twice (L/R).
- Adjust Volume: Click the touch control once (L/R) to decrease volume, click once (R) to increase volume.
- Switch Song: Click the touch control three times (L/R) to skip to the next track.
- Answer/Hang up Call: Click the touch control twice (L/R).
- Reject Call: Press and hold the touch control for 2 seconds (L/R).
- Voice Assistant: Press and hold the touch control for 2 seconds (L/R).
Key:
- x 1: Click Once
- x 2: Click 2 Times
- x 3: Click 3 Times
- 2s: Press and hold for 2 seconds
Problem handling
- Can be connected but there is no sound: Click the right earbud to increase the volume.
- One earbud cannot be charged: Clean the charging contacts of the earbuds and the charging case.
- One earbud cannot be connected: Reset the earbuds.
If you cannot solve the problem, please contact Shenzhen DOKE Electronic Co.,Ltd.
Caution: Please clean the charging contacts of the earbuds and charging case frequently to avoid charging failures.
TECHNICAL SPECIFICATIONS
- Earbuds driver
- 16.2 mm neodymium magnet sound Units x 2
- Frequency Response
- 20-20,000 Hz
- Microphone
- Omnidirectional MEMS x1 (per earbud)
- Bluetooth Version
- Bluetooth 5.3
- Bluetooth profile
- SBC, AAC
- Audio Codec
- SBC, AAC
- Wireless operating frequency
- 2402-2480 MHz
- Wireless transmission range
- Up to 10 meters (measured in open area). Walls and wall structures may affect the transmission range of the device.
- Playback time
- Up to 5 hours on a single full charge. Total playback time: 20 hours^.
- Battery
-
Earbuds: Rechargeable lithium-ion Polymer Battery 3.7 V 90 mAh 0.333 Wh
Charging case: Rechargeable lithium-ion Polymer 3.7 V 500 mAh 1.85 Wh - Charging time
- ≈ 2 hours
- IP Rating
- IPX7 waterproof
- Operating temperature
- 0-45°C
- Maximum output power
- 5 dBm
- Input rated power
- 5V 1A
^Based on moderate volume. Actual battery life will vary, depending on specific use, settings, and environmental factors.
NOTE: Compliance markings are in the charging case.
CAUTION: Do not use the earbud at a high volume for extended periods of time as this may cause hearing loss.
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.
RF Exposure Information: The device was evaluated to meet general RF exposure requirements. This equipment should be installed and used with a minimum distance of 0 mm between the radiator and your body.
Shenzhen DOKE Electronic Co.,Ltd
Address: 13/F, Wei Dong Long Business Building B, Mei Long Ave, Long Hua New District Shenzhen.
Follow Blackview Community
Follow the Blackview community, a place where you can share and discuss with Blackview users and keep posted with the most up-to-date news.
