LOCKLY SECURE

Preparation

To complete the installation you will need:

• Phillips Screwdriver
• Flathead Screwdriver
• Tape measure or ruler
• Pliers
• Screwdriver with drill bits (Optional)

Drilling is not required to install the lock, and is optional. However if you are installing your lock on a brand new door, a drill is required if there are no holes prepared for lock installation.

Preparation

Remove existing door hardware, latch or deadbolts before installing the new lock. Use provided template to bore new holes if needed.

Door Measurements:

• Measure and confirm your door is between 1 3/8" - 2" (35mm - 50mm).
• Measure and confirm the hole in the door is 2 1/8" (54mm).
• Measure and confirm that the backset is between 2 3/8" (60mm) to 2 3/4" (70mm).
• Measure and confirm that hole in the door edge is 1" (25mm).

Step 1: INSTALLING THE LOCKSET

Measure the distance between the center of the front door hole to the edge of your door and select the correct lockset. Select F1 if 2-3/8" (60mm) or F2 if 2-3/4" (70mm).

Diagram showing two lockset options, F1 for 2-3/8" backset and F2 for 2-3/4" backset, with screws labeled 'G'.

Facing the door exterior, install the lockset according to the opening direction of your door.

Diagrams illustrating installation for an 'In-swing Door' and an 'Out-swing Door'.

Secure lockset with provided screws.

Step 2: CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS

Determine right swing or left swing door: While facing the door from the inside, if hinges are on the right side you have the right swinging door. If hinges on the left side you have a left swinging door.

The lock ships set for right swing doors. Skip STEP 2 if your door is a right swing door. See steps below to change door handle orientation for a left swing door.

Changing the Exterior Handle Orientation

1. Insert key and rotate lock face so that the two white dots align as shown.

   Diagram showing key insertion and lock face rotation to align white dots.

2. Use the provided pin insert to push the metal pin located at the 3 o'clock position of the base handle, then the other pin at the 9 o'clock position. Remove the handle once the pins are compressed.

   Diagram showing the use of a pin tool to depress release pins on the handle base.

3. Rotate the handle 180° to the other side of the lock.

   Using your fingers, press the two pins located on the left and right side of the lock to insert the handle back onto the lock.

   Diagram showing handle rotation and reattachment.

Step 2 continued

Exterior Handle Orientation (cont.):

4. Confirm that your installation was complete by checking if the pins are flush against the handle, and have popped out. Adjust the handle accordingly to make sure the pins are fully decompressed and sits flush against the surface.

   Diagram showing a check for correct pin seating with incorrect (X) and correct (✔️) examples.

5. Check that your handle works smoothly by giving it a turn up and down.

   Diagram showing handle operation.

6. Twist key back to horizontal position. The key can be taken out once it goes back to the horizontal position.

   Diagram showing the key in the horizontal position for removal.

Step 2 continued

Changing the Interior Handle Orientation

1. Remove the screw by turning counter-clockwise and rotate the handle 180° in the direction of the arrow as shown. Make sure the screw hole is aligned with the marker as illustrated.

   Diagram showing removal of a screw and rotation of the interior handle mechanism.

2. Securely screw clockwise as shown to complete your handle orientation change.

   Diagram showing re-securing the interior handle mechanism with a screw.

Step 3: PREPARING LOCK FOR INSTALLATION

If you drilled a hole in Preparation, use Slotted Barrel Extension U and securely tighten with a flat head screwdriver by turning it clockwise onto the lock. If you did not drill a hole in Preparation, you can leave this pole removed.

1. Install Spindle C with the holes side into the base of the lock and align the holes located at the 3 o'clock and 9 o'clock positions.

   Diagram showing Spindle C installation into the lock base.

2. Insert locking pin D into the hole as shown above.

   Diagram showing Locking Pin D insertion.

3. Carefully bend the end of the locking pin D with a needle nose pliers.

   Diagram showing bending the locking pin with pliers.

   Note: Failure to bend the locking pin and turn the handle freely without obstruction will result to malfunction.

4. Peel paper layer OFF the Adhesive tape and prepare for installation.

   Diagram showing peeling adhesive tape.

Step 4: INSTALLING THE LOCK (EXTERIOR)

1. Install the exterior lock as shown to the left by aligning the lock straight and passing the cable and attached rods through the lockset.

   Diagram showing exterior lock alignment and passing components through the door.

2. Pass the Spindle C through the center of the lockset, and the round rods through the sides in their respective holes. The cable should run underneath the lockset.

   Diagram illustrating the path of the spindle, rods, and cable.

3. Align the lock straight and press hard (if you use the Adhesive tape in step 3.4) to secure the top of the lock.

   Diagram showing securing the exterior lock assembly.

Step 5: INSTALLING THE LOCK (INTERIOR)

1. Insert Positioning Rods V into the holes to the left and right of the Spindle C. The holes are located at the 3 o'clock and 9 o'clock positions.

   Diagram showing insertion of Positioning Rods V into the lock interior.

2. Interior Mounting Plate LK will go against the interior side of your door. Remove the paper layer off of the Adhesive Tape and align the positioning rods on the bottom of the plate to the corresponding left and right holes.

   Diagram showing the Interior Mounting Plate LK and alignment of positioning rods.

   Positioning rods slide through these holes.

   Install the side with the black plastic seal against the door.

Step 5 continued

3. Pull the cable from the lock exterior through the rectangular hole underneath the positioning rods and spindle. Secure the hole above the spindle with screws O.

   Diagram showing cable routing and securing the mounting plate with screws.

4. Remove the position rods V and replace them with screws O. Tighten clockwise until the mounting plate is secure.

   Diagram showing replacement of positioning rods with screws.

   * If you have drilled a hole on the top in Preparation, please secure the hole with screw M1 or M2 depending on your door thickness. Skip this if no hole was drilled in Preparation.

   Details of M1 (PM5 X 25mm) and M2 (PM5 X 35mm) screws.

Step 5 continued

5. Plug X cable that is coming through the door into the lock interior Y. Match red side of the plug with red on socket - insert tightly.

   Diagram showing the cable connection between exterior and interior lock components.

   NOTE: If you need to disconnect the cable, make sure to press the snap tab to release the plug before carefully pulling it out. Do not force, as this may result in damaging the lock.

6. Align the square rod to the lock interior and attach the Interior lock to the Interior mounting plate. While you are doing so, gently push some of the excess cable through the rectangular hole into the door. Place the remaining cable against the interior side of the lock interior so the lock interior sits securely onto the mounting plate. Make sure the cable is away and not tangling with the square rod C.

   Diagram showing attachment of the interior lock to the mounting plate and cable management.

Step 5 continued

7. Once the lock interior is flush against the mounting plate, secure the lock to the plate by screwing clockwise using provided screws P.

   Diagram showing securing the interior lock with screws P.

8. Insert 4 AA batteries into the lock by aligning the positive and negative orientation markings on the batteries to the battery chamber.

   Diagram showing battery insertion.

   Secure the battery cover by sliding the cover over the lock and turning the screw clockwise on top until tight.

   Diagram showing battery cover installation.

Step 6: INSTALLING THE DOOR STRIKE

Close your door to see if your lock closes securely with your existing door strike. If the lock closes securely, you may keep the existing door strike without removing the old hardware. However, it's recommended that you use LOCKLY's door strike.

Diagram showing door strike installation with screws G and strike plate H.

Make sure the slanted side of Latchbolt (F1/F2) is closing against the slanted part of Strike Plate H before fixing it on to the door frame.

Step 7: DOWNLOAD THE LOCKLY® APP

Congratulations! You have completed the LOCKLY Secure physical lock installation. To complete your setup, download the LOCKLY app from the iOS or Google Play app Store and follow on-screen instructions.

Scan or visit LOCKLY.com/app

Image of a smartphone displaying the LOCKLY app icon, with QR code and app store download buttons.

Smart Home Ready

SECURE LINK

You can add live status monitoring and voice control capabilities to your LOCKLY® Smart Lock with Amazon Alexa or Google Assistant via installing the Secure Link (PGH200) Wi-Fi Hub and Door Sensors (Sold Separately).

Know it's Closed.

Wireless Door Sensors

No more worries wondering if your door was shut when you locked your door. Included is a set of wireless door sensors that can provide accurate information on the status of your door. Whether it's securely shut or still open.

Image of LOCKLY Secure Link Wi-Fi Hub and Door Sensors.

Connected. Always In The Know

Lock, unlock, and monitor your smart lock remotely, whenever, wherever. The 2.4 GHz (802.11 b/g/n) Wi-Fi enabled hub connects seamlessly to your smart lock and app, and provides live updates whenever you need them including live access history without connecting via Bluetooth to the lock.

Smart Home Integration

Amazon Alexa or Google Assistant

Configure your voice commands in your Alexa or Google Assistant app to work with your smart lock. Give commands like “Is my front door locked?” or “Lock my front door”.

Get one now to enable the above features.

https://LOCKLY.com/hub

Regulatory Information

FCC Warning:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

FCC Radiation Exposure Statement

The Secure Link Wi-Fi Hub complies with FCC radiation exposure limits set forth for an uncontrolled environment. It should be installed and operated with minimum distance 20cm between the radiator & your body.

IC WARNING

This device contains licence-exempt transmitter(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:

• (1) This device may not cause interference.
• (2) This device must accept any interference, including interference that may cause undesired operation of the device.

L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d'Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:

1. L'appareil ne doit pas produire de brouillage;
2. L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

IC Radiation Exposure Statement

This equipment meets the exemption from the routine evaluation limits in section 2.5 of RSS-102. It should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body.

Cet équipement est conforme à l'exemption des limites d'évaluation habituelle de la section 2.5 de la norme RSS-102. Il doit être installé et utilisé à une distance minimale de 20 cm entre le radiateur et toute partie de votre corps.

INSTALLATION OVERVIEW & PARTS LIST

This lock can be installed for both right swing and left swing doors. The lock ships ready for a right swing door installation. If you wish to change the orientation of the lock for a Left Swing door, follow instructions on Installation Guide (Step 2) or the BILT App (Step 10).

Detailed diagram showing all parts of the LOCKLY Secure lock and their assembly. Parts are labeled with letters and numbers (e.g., Q Battery Cover, BM4 x 8MM Screw, N Interior Assembly, M PM5 Screw, LK Mounting Plate, S Interior Adhesive, O, BM4 x 32MM Screw, H Strike Plate, KA4 x 20MM Screw, F Latch, F1 Latchbolt, F2 Latchbolt, U Slotted Barrel Extension, C Spindle, D Locking Pin, T Exterior Adhesive, R Clamping Tool, B Exterior Assembly, A Keys, W Activation Card).

Screw Types:

• M1: PM5 x 25MM Screw, Door thickness 1-19/50"~1-69/100" (35~43mm)
• M2: PM5 x 35MM Screw, Door thickness 1-69/100"~1-97/100" (43~50mm)

* NOTE: You can either use the exterior adhesive (T) or slotted barrel extension (U) to stabilize the exterior part. Slotted barrel extension (U) requires drilling an extra hole. Use provided Template for drilling instructions if needed.

Backset Measurement: Measure distance between the center of the hole to the edge of door: Use F1 if 2-3/8" (60mm) or F2 if 2-3/4" (70mm).

Contact Information:

• AUTHENTIC LOCKLY PRODUCT | DESIGNED IN USA | CARD IS PRINTED WITH A SPECIFIC PATTERN
• LOCKLY®
• LOCK SERIAL: PGDxxxxxXXXXX
• ACTIVATION CODE: XXXXXXXX
• SCAN & SAVE
• SECURE ADDITIONAL DOORS AT A DISCOUNT: HTTP://WWW.LOCKLY.COM/MORE
• LOCKLY.COM | HOTLINE: +1(669) 500-8835 | EMAIL: HELP@LOCKLY.COM
• ACC20200402