Anko Low Voltage Sausage Dog Inflatable
Instructions for Use and Safety
These instructions are for your safety. Please read through them thoroughly before use and retain for future reference.
Before You Start
- Decide on an appropriate location for your product (see Installation instructions below).
- If you have any doubt about installing this product, consult a qualified electrician.
Installation Instructions
- This inflatable product is suitable for INDOOR AND OUTDOOR USE.
- The AC adaptor MUST be installed INDOORS away from weather.
- Do not position or place near heaters or any other direct sources of heat.
- This product is suitable for positioning on surfaces which have normal flammability, e.g., wood, plasterboard, masonry. However, this does not include highly flammable surfaces (e.g., polystyrene, textiles).
- Always position cables and extension leads so that they will not be a hazard to the elderly, pets, and children.
- DO NOT position this inflatable product where it may become covered by other items, e.g., curtains, nets, or bedding.
- Ensure the unit is positioned so that you have enough cable to reach an indoor mains power socket.
Warnings
- This inflatable product is suitable for INDOOR AND OUTDOOR USE.
- This product is NOT designed for permanent or long-term use.
- The AC adaptor MUST be installed INDOORS away from weather.
- The supplied adaptor is suitable for operation of LED Modules only.
- Only operate this light chain with the supplied adaptor, Model No. JT-DC12V7.2W-E4.
- Do not connect this inflatable product electrically to another inflatable product.
- Do not connect this light chain to the power supply while it is in the packaging.
- DO NOT attempt to replace the non-replaceable bulbs in this inflatable product.
- Never allow any part of the set to come into contact with a source of heat or flame.
- Care must be taken to avoid damage to the cable or fittings.
- If any part of the light set or cable is damaged, the light set MUST be discarded.
- This product is for use as a decoration only. Not to be used by children as a toy. Keep out of reach of children.
- Do not position this light chain where it will be exposed to extreme wet weather or submerged in water.
- Always switch off this light set or unplug an adaptor if unattended.
- DO NOT overload power sockets or extension leads.
- DO NOT pierce the cable when securing in place, bend or stand on the light chain, as this will damage the bulbs or wiring.
- Please refer to the packing or product rating label for product class, specifications, and rating.
Assembly Diagram
The assembly diagram illustrates the setup process in two steps:
- Step 1 shows the inflatable sausage dog in its deflated state.
- Step 2 shows the inflatable sausage dog fully inflated, with the AC adaptor and power cable connected, ready for use.
LED Bulbs Information
This inflatable product is constructed with non-replaceable bulbs. DO NOT attempt to replace any of the bulbs in the light set.
Keycode: 43199341
Adaptor Manual
General Usage
- Please use the equipment according to the rated voltage and current.
- Do not open the cover of the equipment.
- For use with LED lighting equipment.
- The input and output voltage should be checked before use to ensure correct use.
- This is a Class II product, only for indoor use.
- The product is not a toy; keep it where children cannot reach.
- The lamp controlgear does not rely upon the luminaire enclosure for protection against accidental contact with live parts.
- If applicable: an indication that the controlgear is suitable for operation with LED modules.
- Do-not-cover classification.
Adaptor Specifications
| Model No. | Voltage | Input Rated Frequency | Current | Output Rated Voltage | Power |
|---|---|---|---|---|---|
| JT-DC12V7.2W-E4 | 220-240VAC | 50-60Hz | 0.10A Max | 12V AC | 7.2W |
Clearance Requirements for Combustible Materials
The power supply can be used where normally flammable materials, including building insulation, are or may be present, but cannot be abutted against any material and cannot be covered in normal use. A minimum clearance distance from the top and sides of the control gear to normally flammable building elements is 75mm. This is illustrated in the diagram, where A, B, and C represent minimum clearance distances of 75mm.
Diagram Description: The diagram shows a power supply unit (LED Drivers) positioned near a combustible building element. It indicates required minimum clearances (A, B, C) of 75mm from the control gear to the building element, which may include loose fill insulation or loose combustible materials. A barrier may be required for such materials.
