250 LED MULTI-COLOURED STRING LIGHTS

Instructions for Use and Safety

These instructions are for your safety. Please read through them thoroughly before use and retain for future reference.

Before You Start

• Decide on an appropriate location for your product (see Installation instructions below).
• If you have any doubt about installing this product, consult a qualified electrician.

Installation and Instruction

1. This string light is suitable for INDOOR AND OUTDOOR USE.
2. The AC adaptor MUST be installed INDOORS away from weather.
3. Do not position or place near heaters or any other direct sources of heat.
4. This product is suitable for positioning on surfaces which have normal flammability, e.g. wood, plasterboard, masonry. However this does not include highly flammable surfaces (e.g. polystyrene, textiles).
5. Always position cables and extension leads so that they will not be a hazard to the elderly, pets and children.
6. DO NOT position this set where it may become covered by other items e.g. curtains, nets or bedding.
7. Ensure the unit(s) is positioned so that you have enough cable to reach an indoor mains power socket.

Important Warnings

• Do not try to remove these non-replaceable bulbs.
• This product is NOT designed for permanent or long term use.
• Only operate this light chain with the supplied adaptor, Model no. JT-EL/FC24V3.6W-H6.
• The supplied adaptor is suitable for operation of LED Modules only.
• Do not connect this light chain electrically to another chain.
• Do not connect this light chain to the power supply while it is in the packaging.
• If any part of the light set or cable is damaged, the light set must be discarded.
• This product is for use as a decoration only. This is not a toy.
• Do not position the light chain where it may be exposed to extreme weather conditions or submerged in water, i.e. inside guttering.
• Always switch off the light set or unplug an adaptor if unattended. Do not overload power sockets or extension leads.
• Please refer to packaging or product rating label for product class, specifications and rating.
• DO NOT pierce the cable when securing in place, bend or stand on the light chain, as this will damage the bulbs or wiring.

LED Bulbs

This light set is constructed with non-replaceable bulbs. DO NOT attempt to replace any of the bulbs in the light set.

Adaptor Manual

Keycode: 43069736

1. Do not open the cover of the equipment.
2. The power supply is suitable for LED modules.
3. The input and output voltage should be checked before use to ensure correct use.
4. This is the Class II product; JT-EL/FC24V3.6W-H6 is only for indoor use.
5. The product is not a toy; keep it where children cannot reach.
6. The lamp controlgear does not rely upon the luminaire enclosure for protection against accidental contact with live parts.
7. The adaptor is for socket mounted only. Not for Recess Use.
8. The minimum clearance distance from the top and sides of the controlgear to normally flammable building elements is 225 mm and 300 mm.
9. The minimum clearance distance from the top and sides of the controlgear to normally flammable building elements.
10. If the minimum clearance distances from each side of the controlgear are different, or there are different minimum clearance distances for various types of normally flammable building element or building insulation, then each minimum clearance distance shall be stated separately.
11. Where controlgear is required to be mounted on a specific surface or has additional installation requirements, for example, use in non-combustible enclosed space or to ensure adequate sealing to maintain its IP rating, the relevant information shall be supplied with the controlgear.

NOTE: Installation in a non-combustible enclosed space may include installation in a rebate in a concrete slab, ceiling or wall.

Diagram: Installation Clearance Details

The diagram illustrates the required minimum clearance distances for the adaptor's controlgear when installed near normally flammable building elements. The adaptor requires a minimum clearance of 300 mm from the top and 225 mm from the sides of the controlgear to any flammable building material. This ensures adequate ventilation and prevents heat buildup.