Solar-Powered Siren

Product Overview

The solar-powered siren is a totally wireless siren, designed to help protect yards, driveways, gardens, and all types of other external locations. The strobe siren is battery powered and kept re-charging by the built-in solar panel. The signal transmission is all by wireless radio frequency which achieves significantly wirefree transmission and enhances the flexibility to install. Users can install some outdoor strobe sirens to deter the intruders in Omni-directional guard.

The strobe outdoor siren can be used as a wireless siren by connecting to the control panel as well as a standalone alarm system to work with wireless accessories in the same frequency by learning.

Jumper Setup

Volume Setting

• High (default)
• Mute
• Low

Siren Duration Setting

• 5 minutes
• 2 minutes
• 30 seconds (default)

PCB Layout

• Siren Duration Setting
• Volume Setting
• Power On/Off
• Internal Tamper Switch
• Learning Button
• External Tamper Switch
• Status LED Indicator
• Alarm LED Indicators

Note: The status LED will flash once every 5 seconds in arm status. It will not flash when in disarm status. The siren will sound immediately if the tamper switch is triggered.

Usage

Getting Started

1. Load the 9V battery.
2. Set the volume and duration of the siren.
3. Start to use by pressing the power button on.

Note: The 9V battery is used to charge the 18650 battery in case it is out of power/with low power after a long-time storage. Use the 9V battery to charge the 18650 battery for 12 hours and then remove the 9V battery before installation.

Work as a Wireless Siren

Connect to Alarm Panel

Press the learning button (0.5 seconds), the wireless siren goes into connecting status after one beep is heard. Press SOS or Arm button on the panel (or press Arm on App if the panel does not have a button), the wireless siren is connected successfully with the control panel after another beep.

To give up the connection, press the learning button again to exit.

Note: Please don't trigger any accessory during connecting with alarm panel.

After connected to the alarm panel, the siren will hoot and the strobe light will flash when the alarm panel alarms.

Work as an Alarm Panel

Connect with Wireless Accessories

Press the learning button (0.5 seconds), the system goes into connecting status after one beep is heard. Press test button on accessories or trigger the accessory once. The wireless accessory is connected successfully after another beep. To give up the connection, press the learning button again to exit connecting status after one beep.

After connected with wireless accessories, the siren will hoot and the strobe light will flash to deter the burglar on site when the accessories detect intrusion.

Note: No matter the siren works as a wireless siren or an alarm panel, if disarm is not operated after the siren duration time, the status indicator of siren will flash once every 2 seconds to inform user or patrol police that the alarm system has been triggered. This LED indication lasts for 1 hour.

Enter/Exit Connecting Status by Connected Remote Control

When the siren is working as a standalone alarm system and installed on the wall, newly purchased accessories may not easy to connect with the siren. With this function, user can easily connect the accessories to the siren without dismounting the siren from the wall.

1. Press on the remote control 3 times (within 5 seconds) to enter service mode.
2. Then press 3 times (within 5 seconds) to enter connecting status.

A longer beep is heard from the siren means it enters connecting status, press test button on the newly purchased accessory or trigger the accessory once. Another beep is heard from the siren, the accessory has been successfully connected with the siren.

Press on remote control to exit connecting status after a short beep.

Disconnect with All Alarm Panels or Accessories

Press and hold the learning button of this siren for 5 seconds and release the button when two beeps are heard, all the paired alarm panels or accessories are disconnected.

Installation

Service Mode

The service mode is to prevent triggering the alarm when you mount the siren on the wall. When the remote control is connected with the siren, press on remote control 3 times (within 5 seconds), the siren goes into service mode when a long beep is heard. During this period, the siren will not alarm but beep even if the tamper switch or the sensors connected are triggered. This brings you convenience on installation.

Press on remote control to exit service mode after a short beep.

Note: Also you can press the tamper switch 7 times to enter installation mode.

Installation Steps:

1. Drill four holes and fit the wall plugs, and then fit supplied fixing screws in the holes.
2. Hold the mounting plate in position and mark the positions of the four mounting holes. A spirit level placed on the waterproof casing will ensure a perfect level.
3. Remove the fixing screw from the bottom edge of the siren housing and carefully remove front cover.
4. Hinge the front cover locating tabs over the top edge of the back plate and carefully push the base of the siren cover into place. Secure the siren cover in place by refitting the fixing screw in the bottom edge of the cover.

Specifications

• Backup Power: 18650 3.7V 1800mAh rechargeable lithium battery x 1, 9V 6F22 battery x 1
• Solar Panel Output Current: 2000LUX illumination ≥4mA (in sunlight)
• Maximum Alarm Current: <500mA
• Wireless Receiving Distance: <80m (in open area)
• Operation Condition: Temperature -20°C to +55℃, Relative Humidity <90% (non-condensing)
• Maximum Siren Volume: 110dB
• Static Current: <1mA
• Standby Time: <45 days (in case of no sunlight)
• Wireless Receiving Frequency: 315MHz or 433.92MHz (±75KHz) *Only 433.92MHz is available for Europe
• Housing Material: PC + ABS + ANTI-UV
• Size (L x W x H): 309 x 230 x 79.7mm

CE Declaration of Conformity

Hereby, Chuango AloT GmbH declares that the radio equipment type SPS-260 Solar-Powered Siren is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://www.chuango.com/english/compliance_SPS-260

INFORMATION FOR THE USERS

At the end of its life, the device has to be separated from the other waste. Consign the device and all its components together to a center of electronical and electrotechnical waste recycling center, designated by your local authorities.

Battery Directive: 2006/66/EC and its amendment 2013/56/EU (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info.