Mini Strobe Siren WS-105

Introduction

The wireless siren is powered by AC 100V~240V, requiring no wiring. Users can install multiple wireless sirens in different locations to deter illegal intruders.

Features

• Compact size with plug-in design
• 100% wireless configuration, D.I.Y. Installation
• Built-in 1,000,000 RF codes combination for high reliability
• E₂PROM information protection prevents data loss on power failure
• Simplified accessory expansion via automatic connecting
• Works with all Chuango wireless accessories
• Mute operation for night use, not disturbing the neighborhood
• Built-in 3.7V/600mAh lithium battery provides 8-hour standby

Product Overview

The siren can be wirelessly connected with a control panel to build a system. When the control panel receives alarm signals, the wireless siren will hoot and the strobe light will flash. It can also function as a standalone alarm system.

Components:

• ① Power Switch/Connect Button
• ② Strobe Light
• ③ Siren

Siren and Strobe Light Indication

• When armed: Siren beeps once, strobe light on after one flash.
• When disarmed: Siren beeps twice, strobe light goes out after two flashes.
• When armed or disarmed in mute: Siren does not beep, and the strobe light does not flash.

Power On/Off

• Power On: Plug the siren into an AC power socket and press the power switch button. The siren powers on after a long beep.
• Power Off: Press the connect button once while the siren is on. Then press and hold the connect button for 6 seconds until a long beep is heard. The siren powers off.

Work as Wireless Siren

When working with a wireless control panel, the siren hoots and the strobe light flashes when the panel is alarming to deter intruders. Connect the siren to the control panel in advance.

Connect to Control Panel

1. Press the connect button (0.5 seconds). The siren beeps once. After 3 seconds, it beeps again, and the strobe light flashes, entering connecting status.
2. Press the [SOS] or [Arm] button on the control panel. The siren and panel connect successfully after one beep. Press the connect button again to exit connecting status (two beeps).

Note: Do not trigger any accessory during the connection process.

Work as Standalone Alarm

The siren can create a standalone alarm system by adding wireless accessories. When armed, if a sensor is triggered, the siren will hoot and the strobe light will flash to deter intruders.

Connect Wireless Accessories

1. Press the connect button (0.5 seconds). The siren beeps once. After 3 seconds, it beeps again, and the strobe light flashes, entering connecting status.
2. Press the wireless accessory (e.g., a button on a remote control or the magnet of a door sensor). It will connect after one beep. Repeat for other accessories.

Note: The siren supports up to 40 wireless accessories.

Testing

Press the [Arm] button on the remote control. If the siren flashes once, the remote control connection is successful. Trigger a sensor; the siren should sound. If not, the connection failed; please reconnect.

Clear All Accessories or Panels

If wireless accessories are lost, clear them to prevent unauthorized use. Press and hold the connect button for 6 seconds until one beep is heard. The LED indicator flashes twice, clearing all connected accessories and panels. Reconnect accessories or panels to use the siren.

Entry and Exit Delay

Entry and exit delay can be applied when wireless accessories are set to Independent Delay Zone. After setup:

• Press [Arm] once: Siren beeps every 5 seconds until Arm status.
• Press [Arm] twice: Siren enters Arm status immediately.

When a triggered accessory activates the siren after the delay time (3 minutes ringing time), the siren will sound.

Setup Method:

• Press connect button twice: 15 seconds delay.
• Press connect button three times: 30 seconds delay.
• Press connect button four times: no delay.

Default setting: no delay.

This delay setting is only effective for accessories in Independent Delay Zone, not for those in Home Mode Zone or Normal Zone.

Zone Setting for Wireless Accessories

• Independent Delay Zone: Allows for entry/exit delays.
• Normal Zone: Standard zone.
• Home Mode Zone: Press [Stay] button on the remote. Siren beeps once. All detectors are armed except those in "Home Mode Zone", which are disarmed, allowing free movement at home.
• 24-H Zone: System alarms immediately when a detector in this zone is triggered, regardless of system status.

If zone settings are changed, accessories must be re-connected with the control panel.

Switch On/Off Night Lamp

When used as a standalone alarm, the siren can also function as an LED night lamp.

• Press the [Stay] button twice on the remote control to enter Home Mode. The strobe light will switch on silently as a night lamp.
• Press the [Disarm] button to disarm the system and switch off the strobe light.

Specifications

• Power Supply: AC 100V~240V
• Volume: 90dB
• Backup Battery: 3.7V/600mAh Lithium Battery, 2.22Wh
• Static Current: < 13mA
• Alarm Current: < 100mA
• Radio Frequency: 315MHz or 433.92MHz(±75KHz)
• Housing Material: ABS plastic
• Operation Condition: Temperature: 0°C ~ +55°C, Relative Humidity: < 80% (non-condensing)
• Dimensions: 90 x 90 x 42.2mm (excluding plug part)