IKEA BAGGEBO Storage Unit Assembly Instructions
Safety First: Preventing Tip-Over Accidents
WARNING!
Serious or fatal crushing injuries can occur if furniture tips over. To prevent this, the furniture must be secured to the wall using the provided wall attachment devices.
Please note that screws and plugs for the wall are not included. It is essential to use screws and plugs that are suitable for your specific wall type. If you are uncertain, seek professional advice. Carefully read and follow each step of the instructions.
This critical safety information is provided in multiple languages.
Product Identification
This document provides assembly instructions for the IKEA BAGGEBO storage unit.
Included Hardware
The following components are included in the package:
- 10x Screws (Part No. 100229)
- 12x Dowels (Part No. 101345)
- 1x Screw (Part No. 109041)
- 2x Washers (Part No. 100823)
- 1x Allen Key (Part No. 100006)
- 1x Plastic Bracket (Part No. 105493)
- 4x Plastic Covers/Caps (Part No. 122628)
- 1x Bag of Nails (Part No. 319503)
- 1x Wall Bracket (Part No. 106989)
Assembly Steps
Follow these steps carefully to assemble your BAGGEBO unit:
-
Step 1: Attach Wall Bracket to Panel
Take one side panel and attach the wall bracket (106989) using one screw (109041) and one washer (100823). Ensure the bracket is oriented correctly for later wall attachment.
[Visual: A metal bracket is attached to a wooden panel using a screw and washer. An inset shows correct versus incorrect screw placement.] -
Step 2: Insert Dowels
Insert twelve dowels (101345) into the pre-drilled holes on the edges of the main wooden panels.
[Visual: Dowels are shown being inserted into the holes on the edges of panels.] -
Step 3: Connect Side and Base Panels
Connect the two side panels to the base panel, aligning the dowels with their corresponding holes. Secure these connections.
[Visual: Two side panels are being connected to a base panel. Hands are shown guiding the assembly.] -
Step 4: Continue Frame Assembly
Continue building the main frame by connecting the remaining panels, utilizing the inserted dowels for alignment.
[Visual: The unit's frame is shown taking shape as more panels are joined together.] -
Step 5: Secure Main Frame
Use the provided Allen key (100006) to insert and tighten five screws (100229) to firmly secure the main structure of the unit.
[Visual: The Allen key is shown being used to tighten screws into the assembled frame.] -
Step 6: Install Back Panel
Carefully slide the back panel into the grooves located on the rear of the assembled unit frame.
[Visual: An arrow indicates the back panel being slid into its designated grooves.] -
Step 7: Fasten Back Panel
Secure the back panel in place by inserting five screws (100229) into the pre-drilled holes along the edges.
[Visual: Screws are shown being inserted to fasten the back panel to the unit.] -
Step 8: Attach Bottom Supports
Attach the plastic brackets (105494) to the bottom of the unit using fourteen screws (101221).
[Visual: Plastic brackets are shown being attached to the bottom of the unit with screws.] -
Step 9: Install Protective Covers
Gently tap four plastic covers (122628) into the exposed screw heads or connection points using a hammer.
[Visual: A hammer is shown being used to tap plastic caps into place.] -
Step 10: Final Wall Securing
Position the assembled unit against the wall. Attach the unit to the wall using the previously attached wall bracket (106989) and appropriate wall fixings (not supplied). Ensure the unit is firmly anchored to prevent any risk of tipping.
[Visual: The assembled unit is shown being positioned against a wall, and the wall bracket is being secured to the wall.]
Important Note on Wall Fixings
The correct screws and wall plugs for your specific wall type are crucial for safety. If you are unsure about the correct fixings, please consult a professional or your local hardware store.
