Rheem® Hybrid Electric Heat Pump Water Heater
Designed for Residential Builders to Maximize Energy Design Rating/HERS Rating
Product Highlights
- 3.50 UEF (Uniform Energy Factor)
- Meets NEEA Tier 3 Requirements
- Integrated Wi-Fi Technology
- California Title 24 Compliant (JA13 Ready)
- LeakSense™ Accessory Ready
- Design Certified to NSF/ANSI 372 (lead control)
- 10 Year Limited Warranty¹
Features & Benefits
| Category | Description |
|---|---|
| High Efficiency |
ENERGY STAR® 5.0 certified Helps builders earn 45L tax credits |
| Easy Installation |
Easily Ducted - for installation in confined spaces with minimal make up air Easy access to side water connection and top electrical junction box; Zero clearance required in the back or side of the unit ¾" NPT water inlet & outlet; ¾" condensate drain connections Dry fire protection |
| Available EcoNet® Smart Technology |
Integrated Wi-Fi Technology² Energy usage reporting Energy saving scheduling and operating modes |
Note: ¹ See Residential Warranty Certificate for complete information. ² Wi-Fi broadband internet connection required. ³ Consult your tax advisor for details on eligibility requirements for any available tax credits. Rebates vary by state.
Specifications
Model Series: Hybrid Electric Heat Pump - Builder
Capacities: 40, 50, 65 and 80-Gallon
Electrical: 208-240 Volt / 1 PH / 24 Amps
LEED Points: 3
| Nominal Gallon Capacity | Rated Gallon Capacity | Model Number | Model Variant | Electric Breaker Size | Uniform Energy Factor (UEF) | Compressor BTU/H | First Hr. Rating G.P.H. | Recovery G.P.H. 90° F Rise | Unit Wt. (LBS) | Approx. Ship Wt. (LBS.) |
|---|---|---|---|---|---|---|---|---|---|---|
| 40 | 36 | PRO H40 T2RH310BM | 700461 | 30 | 3.50 | 4200 | 60 | 26 | 156 | 177 |
| 50 | 45 | PRO H50 T2RH310BM | 700455 | 30 | 3.50 | 4200 | 67 | 26 | 172 | 193 |
| 65 | 59 | PRO H65 T2RH310BM | 700456 | 30 | 3.50 | 4200 | 75 | 26 | 225 | 262 |
| 80 | 72 | PRO H80 T2RH310BM | 700457 | 30 | 3.50 | 4200 | 87 | 26 | 244 | 281 |
Uniform Energy Factor and rated gallon capacity based on Department of Energy (DOE) requirements. Units meet or exceed ANSI requirements and have been tested according to D.O.E. procedures. Units meet or exceed the energy efficiency requirements of NAECA, ASHRAE standard 90, ICC Code and all state energy efficiency performance criteria.
Dimensions
Diagram Description: The diagram illustrates the physical dimensions of the Rheem Hybrid Electric Heat Pump Water Heater Builder Series. Key dimensions labeled A through J are provided for each model capacity. A note indicates "2 inches Clearance Needed for T&P Release".
| Nominal Gallon Capacity | Model Number | Dimension A | Dimension B | Dimension C | Dimension D | Dimension E | Dimension F | Dimension G | Dimension H | Dimension I | Dimension J |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 40 | PRO H40 T2RH310BM | 62-5/16" | 20-1/4" | 47" | 3-5/8" | 39-5/8" | 25-1/4" | 20-1/2" | 78-7/8" | 22-3/8" | 21-3/4" |
| 50 | PRO H50 T2RH310BM | 61-3/4" | 22-1/4" | 47" | 3-5/8" | 39-5/8" | 27-1/8" | 22-1/2" | 78-5/8" | 24-3/8" | 23-5/8" |
| 65 | PRO H65 T2RH310BM | 64-3/16" | 24-1/4" | 49" | 3-7/8" | 42-3/8" | 29-5/16" | 24-5/8" | 81-1/8" | 26-1/2" | 25-13/16" |
| 80 | PRO H80 T2RH310BM | 74-3/16" | 24-1/4" | 59" | 3-7/8" | 52-3/8" | 29-1/4" | 24-5/8" | 91" | 26-1/2" | 25-11/16" |
Installation Guidelines
The following describes installation requirements based on room size and ducting configurations:
Heater: Not Ducted
Scenario 1: Large Room
Room size: Larger than 700 ft³ (e.g., 7' x 10' x 10').
Requirements: No additional ventilation needed.
Scenario 2: Smaller Room
Room size: Smaller than 700 ft³ (e.g., 7' x 10' x 10').
Requirements: Full louvered door OR two louvers (top and bottom). See below.
Scenario 3: Small Closet Installation
Requirements:
- Air gap under door equal to 18 square inches (0.75 inches clearance).
- Louver must be located the same height on the door as the air exhaust on the heater.
- Heater air exhaust must be positioned towards the louver within one foot of the door.
Diagram Note: Illustrates a 0.75 inch clearance under the door and a 12 inch maximum distance from the heater air exhaust to the door louver.
Heater: Ducted Installation
Scenario 4: Ducted with Inlet OR Outlet Duct
Room size: Any size room.
Requirements: Air gap under door equal to 18 square inches (0.75 inches clearance).
Scenario 5: Ducted with Inlet AND Outlet Duct
Room size: Any size room.
Requirements: No additional ventilation needed.
Hybrid Builder Accessories
| Part Number | Description | Use For |
|---|---|---|
| SP20882 | Earthquake Isolation Kit | Installations in seismic regions |
| SP20883 | Vibration Isolation Kit | Installation on non-concrete floors |
| SP20884 | 8" Diameter UL Certified Termination Kit | Termination to the outside or to the attic with 8" diameter |
| SP20885 | 7" Diameter UL Certified Termination Kit | Termination to the outside or to the attic with 7" diameter |
| SP20886 | 6" Diameter UL Certified Termination Kit | Termination to the outside or to the attic with 6" diameter |
| SP20887 | 5" Diameter UL Certified Termination Kit | Termination to the outside or to the attic with 5" diameter |
| SP20888 | 8" Rheem Approved Damper Kit | Exhaust only to the outside ducting configuration (no inlet duct) |
| SP20889 | 25' Flexible 8" Diameter Duct Kit | For up to 25' of ducting |
| SP20890 | Rigid Elbow Duct Kit | Installation in tight places where space needs to be minimized |
| AP17829 | Outlet Duct Adapter | Allows for ducting to be connected to the unit |
| AP19134 | Leak Sensor | Automatic detection of internal and external leaks |
| AP21365 | Inlet Duct Adapter | Allows for ducting to be connected on the top inlet |
Accessory Image Descriptions: The page displays images of various accessories including isolation kits, termination kits, damper kits, flexible and rigid duct kits, and duct adapters.
