Tribesigns Assembly Instructions

Contact Us & Support

Warm Tips for Assembly

1. Carefully read these instructions and keep them for future reference.
2. Check the parts list and confirm everything's there before starting assembly.
3. When assembling, put all parts on a soft, smooth surface like a carpet to avoid scratches.
4. Don't fully tighten screws until all parts are confirmed in place to avoid misalignment.

How to Get the Assembly Video

Step 1: Scan the QR code provided for the Installation Video.

Step 2: Search on YouTube for "Tribesigns Installation Guide" and the Model No. "HOGA-J0356".

If you can't find the assembly video, please contact customer service.

Tools & Safety

Recommended Tools: Hand tools are recommended for assembly.

Electric Screwdriver Use: If an electric screwdriver is used, reduce power and torque to avoid damage to the product.

Visual representation of recommended tools and caution regarding electric screwdrivers.

Install the Anti-Tip Straps

Using the anti-tip straps can reduce the risk of tipping over, but cannot eliminate it.

Diagram showing correct installation of anti-tip straps with a checkmark [✔️] and incorrect installation with a cross [❌].

⚠️ Warning: Ensure anti-tip straps are installed correctly to prevent accidents.

Parts Identification

Exploded view diagram showing all parts of the porch table, labeled with numbers 1 through 9.

Caution: Make sure all parts are included. Most board parts are labeled or stamped on the raw edge. Contact Tribesigns for a free replacement if you encounter any damaged or missing parts.

Hardware List

Assembly Steps

Installation of Cams and Pins

Procedure: Screw the pin into the hole. To set the cams correctly, ensure that the arrow on the cam is opening towards the hole of the pin it is locking. Lock the cam by turning the cam head with a screwdriver until it is tightened. Please do not use an electric screwdriver to assemble the unit.

Diagram illustrating the correct insertion and locking of cam pins and cams, showing no gap between parts.

Step 1: Frame Assembly (Part A)

Attach part A (M6X35MM screws) to parts 1 and 2. (8 pcs A used).

Diagram showing the attachment of screws (A) to the base frame components (1 and 2).

Step 2: Attaching Curved Sections (Part C)

Attach parts 3 and 4 using part C (Ø7X38MM screws). (24 pcs C used).

Diagram showing the connection of curved pieces (3) and connector pieces (4) to the main frame using screws (C).

Step 3: Adding More Curved Sections (Part C)

Attach parts 5 and 6 using part C (Ø7X38MM screws). (16 pcs C used).

Diagram showing the attachment of additional curved pieces (5 and 6) to the structure using screws (C).

Step 4: Securing Structure (Part B & F)

Connect the curved sections using part B (Ø6X35MM screws) and Allen wrench F. (16 pcs B used).

Diagram illustrating the use of screws (B) and Allen wrench (F) to secure the assembled curved sections.

Step 5: Attaching Side Panels (Part A)

Attach side panels (part 7) using part A (M6X35MM screws). (8 pcs A used).

Diagram showing the attachment of side panels (7) to the main frame using screws (A).

Step 6: Attaching Top Panel (Part A)

Attach the top panel (part 9) using part A (M6X35MM screws). (16 pcs A used).

Diagram showing the attachment of the top panel (9) to the frame using screws (A).

Step 7: Final Securing (Part D & B)

Secure the structure using cam lock nuts (D) and screws (B). (16 pcs B, 4 pcs D used).

Diagram illustrating the final securing of the table using cam lock nuts (D) and screws (B).

Step 8: Completed Product

Illustration of the fully assembled porch table.

Anti-Tip Kit Installation

This section details how to install the anti-tip kit to secure the furniture to the wall.

Kit Components:

• Brackets (a): 2 pcs
• Steel Cable (b): 1 pc
• Screw (c): 1 pc
• Screw (d): 1 pc
• Expansion Bolt (e): 1 pc

Installation Steps:

1. Drill a hole on the wall, insert the expansion bolt (e) into the hole.
2. Secure one bracket (a) into the expansion bolt (e) using the screw (c).
3. Position the furniture in place. Attach another bracket (a) (aligns with the bracket on the wall) to the back edge of the unit top using the screw (d).
4. Thread the male end of the steel cable (b) through both brackets. Securely join the ends by turning the female connector clockwise.

Note: Before installing the anti-tip kit, please determine where the furniture is to be placed and locate the center line of a wooden stud using a stud finder. For a concrete wall, ensure no steel bars inside it.

Diagrams illustrating each step of the anti-tip kit installation, including drilling, attaching brackets, and securing the cable.