Tribesigns LITTLE TREE Console Table Assembly Instructions

Customer Support

If you have any issues with this product, please contact the Tribesigns customer service team before returning it. We want you to be completely satisfied with your purchase.

If anything is missing, damaged, or incorrect, please keep the outer packaging and take photos of both the packaging and products. Reach out to Tribesigns at support@tribesigns.com or call 1-424-220-6888. Tribesigns will handle everything and send a free replacement.

Assembly Instructions:

1. Carefully read these instructions and keep them for future reference.
2. Refer to the parts list for guidance and ensure all pieces are present before starting assembly. If any parts are missing, damaged, or incorrect, contact Tribesigns before assembling.
3. When assembling, place all parts on a soft, clean, and flat surface, such as a carpet, to prevent scratches.
4. To avoid misalignment of holes, do not fully tighten screws until all parts are in place.

Follow Tribesigns:

Connect with Tribesigns on social media:

• Facebook
• Twitter
• Pinterest
• YouTube
• Instagram

Important Safety Information:

When using an electric screwdriver, reduce the power and torque to avoid damaging the furniture.

Use of tip-over restraints may only reduce but not eliminate the risk of tip-over.

Caution: Make sure all parts are included. Most board parts are labeled or stamped on the raw edge. Contact Tribesigns for free replacement if parts are damaged or missing.

Assembly Tip: Ensure pins are screwed in fully, with no gap between the pin base and the surface. The arrow on the cam should point towards the hole of the pin it is locking. Lock the cam by turning the cam head with a screwdriver until tightened. Do not use an electric screwdriver for this step.

Parts & Hardware List

The following parts are included:

• Part 1: 1 pc
• Part 2: 1 pc
• Part 3: 2 pcs
• Part 4: 2 pcs
• Part 5: 4 pcs
• Part 6: 2 pcs
• Part 7: 2 pcs
• Part 8: 2 pcs
• Part 9: 12 pcs
• Part 10: (Included with Part 9)

Hardware List:

Installation Steps:

Step 1: Install pins (A) into the designated holes on parts 1, 2, 3, and 4. Ensure pins are screwed in straight and fully. Then, insert cams (B) into the larger holes on parts 5, 7, and 8. Ensure the arrow on the cam points towards the edge where the pin will enter.

Step 2: Attach parts 5 to parts 3 and 4 using screws (A). Attach parts 6 to parts 1 and 2 using screws (A).

Step 3: Connect parts 3 and 5 to part 1, and parts 4 and 5 to part 2 using cams (B) and screws (A). Ensure the structure is stable.

Step 4: Attach parts 7 and 8 to the assembled base structures using cams (B) and screws (A). Ensure the cam arrows align with the pins and tighten the cams.

Step 5: Insert the shelf parts (9 and 10) into the vertical supports (7 and 8) using screws (E) and Allen key (I).

Step 6: Attach the top long piece (1) to the assembled side structures using screws (C) and (D).

Step 7: Attach the second top long piece (2) to the assembled side structures using screws (C) and (D).

Step 8: Secure the entire console table by attaching the remaining parts and ensuring all screws are tightened appropriately. Use screws (F) and (H) as needed for final assembly and stability.

Step 9: For safety, secure the console table to the wall using the provided tip-over restraint hardware (F and I). Drill holes in the wall as needed and use appropriate wall anchors if necessary. Attach the restraint straps to the back of the console table and the wall.

Customer Return Policy

Tribesigns' Return Process: Contact support@tribesigns.com for replacement or refund. Tribesigns handles the process efficiently.

Alternative Return Process: Re-package item, schedule pick-up, track package, and await replacement.