KALLAX Desk Assembly

Important Safety Information

[Warning] Serious or fatal crushing injuries can occur from furniture tip over.

To reduce the risk of furniture tip over:

• Always secure the furniture with the fittings provided.
• Ensure the furniture is fixed in all directions before use.
• If uncertain, seek professional advice.
• Read and follow each step of the instructions carefully.

Parts List

The following parts and quantities are required for assembly:

• 18x Part 114613 (Cam bolt)
• 12x Part 101372 (Dowel)
• 4x Part 100372 (Screw)
• 6x Part 114926 (Cam lock)
• 12x Part 102509 (Cam lock)
• 4x Part 104321 (Screw)
• 1x Part 100092 (Hex key)
• 6x Part 157409 (Wheel)
• 2x Part 115753 (Bracket)
• 2x Part 103693 (Bracket)
• 2x Part 118225 (Bracket component)
• 2x Part 118673 (Bracket component)
• 2x Part 115754 (Bracket component)

Assembly Steps

Follow these steps to assemble your KALLAX desk:

1. Step 1: Insert 4x cam bolts (114613) into two main panels. [Visual: Two panels with cam bolts inserted.]
2. Step 2: Connect the side panels to the back panel. [Visual: Panels being joined together.]
3. Step 3: Insert and secure 4x cam locks (102509) into the corresponding holes. Rotate to lock. [Visual: Cam locks being inserted and turned.]
4. Step 4: Attach the base panel using 4x screws (104321) and the hex key (100092). Rotate to tighten. [Visual: Base panel attached with screws and hex key.]
5. Step 5: Insert 4x cam bolts (114613) into another panel. [Visual: Panel with cam bolts.]
6. Step 6: Attach a long panel using 4x dowels (101372) and a hammer. [Visual: Long panel attached with dowels.]
7. Step 7: Insert 2x dowels (101372) into another long panel. [Visual: Another long panel with dowels.]
8. Step 8: Connect the two long panels using the dowels from Step 7. [Visual: Joining the two long panels.]
9. Step 9: Insert 4x dowels (101372) into designated holes on the structure. [Visual: Dowels inserted into the desk frame.]
10. Step 10: Slide a drawer runner component into the main structure. [Visual: Drawer runner sliding into place.]
11. Step 11: Insert 4x cam bolts (114613) into a panel. [Visual: Panel with cam bolts.]
12. Step 12: Slide another component into the main structure. [Visual: Another component sliding into place.]
13. Step 13: Insert and secure 2x cam locks (102509). Rotate to lock. [Visual: Cam locks being secured.]
14. Step 14: Attach 6x wheels (157409) to the base of the desk. Rotate to secure. [Visual: Wheels being attached to the base.]
15. Step 15: Insert and secure 6x cam locks (102509). Rotate to lock. [Visual: Cam locks being secured.]
16. Step 16: Insert 6x dowels (101372) into designated holes. [Visual: Dowels inserted into the desk frame.]
17. Step 17: Insert 6x cam bolts (114613) into a panel. [Visual: Panel with cam bolts.]
18. Step 18: Attach the top surface to the assembled structure. [Visual: Top surface being placed on the desk.]
19. Step 19: Insert and secure 6x cam locks (114926). Rotate to lock. [Visual: Cam locks being secured.]
20. Step 20: Attach 2x brackets (115753) using 2x screws (100372). [Visual: Brackets attached with screws.]
21. Step 21: Attach 2x brackets (103693) to the structure. [Visual: Brackets attached to the desk.]
22. Step 22: Wall mounting: Attach 2x brackets (103693) to the wall using appropriate fixings (not included). [Visual: Brackets being attached to a wall.]
23. Step 23: Position the desk and secure it to the wall brackets. [Visual: Desk being secured to wall brackets.]