KALLAX Shelving Unit

Important Safety Information

❗ WARNING!

Furniture tip-over can cause serious or fatal crushing injuries. To prevent furniture tip-over, this furniture must be used with the wall anchoring device(s) included.

Wall screws and plugs are not included. Use screws and plugs suitable for your walls. If you are in doubt, seek professional advice. Read and follow each step of the instructions carefully.

Tools Required

• Screwdriver ?
• Pencil ✏️
• Hammer ?
• Spirit Level ?

Note: Do not assemble on carpets as this may damage the furniture or the carpet. ❌

Parts Included

The following parts are included in the package:

• 8x Screw (Part No. 104322)
• 16x Dowel (Part No. 101339)
• 12x Dowel (Part No. 101345)
• 4x Screw (Part No. 100372)
• 1x Allen Key (Part No. 100092)
• 1x Wall Bracket (Part No. 121030)
• 2x Corner Bracket Part (Part No. 115753)
• 2x Wall Mounting Plate (Part No. 103693)
• 2x Wall Anchor Bracket (Part No. 118225)
• 2x Hexagonal Decorative Covers (Part No. 10002300)

Assembly Steps

1. Step 1: Initial Bracket Attachment

   Attach the wall bracket (121030) to the base panel using one screw (100092) and one screw (104322). The bracket has multiple slots for adjustment.

2. Step 2: Insert Dowels

   Insert 2 dowels (101339) into the pre-drilled holes on the edge of a side panel. Use a hammer ? to gently tap them in. The diagram shows dowel 101339 being used and dowel 101345 crossed out ❌.

3. Step 3: Insert Dowels

   Insert 2 dowels (101345) into the pre-drilled holes on the edge of the base panel. Use a hammer ? to gently tap them in. The diagram shows dowel 101345 being used and dowel 101339 crossed out ❌.

4. Step 4: Attach Side Panel

   Align the side panel with the dowels (101339) inserted in Step 2 with the corresponding holes on the base panel. Push the panel down to connect. An arrow ▶️ indicates the direction of assembly.

5. Step 5: Insert Shelf Dowels

   Insert 8 dowels (101345) into the pre-drilled holes on the edges of the horizontal shelf panels. Use a hammer ? to gently tap them in. The diagram shows dowel 101345 being used and dowel 101339 crossed out ❌.

6. Step 6: Attach Vertical Divider

   Insert 2 dowels (101339) into the top edge of a vertical divider. Align these dowels with the corresponding holes in the first assembled side panel and push down. An arrow ▶️ indicates the direction of assembly. The diagram shows dowel 101339 being used and dowel 101345 crossed out ❌.

7. Step 7: Attach Vertical Divider

   Insert 2 dowels (101339) into the top edge of another vertical divider. Align these dowels with the corresponding holes in the base panel and push down. An arrow ▶️ indicates the direction of assembly. The diagram shows dowel 101339 being used and dowel 101345 crossed out ❌.

8. Step 8: Attach Vertical Divider

   Insert dowels into the next vertical divider and attach it to the unit.

9. Step 9: Attach Vertical Divider

   Insert 2 dowels (101339) into the top edge of another vertical divider. Align these dowels with the corresponding holes in the base panel and push down. An arrow ▶️ indicates the direction of assembly. The diagram shows dowel 101339 being used and dowel 101345 crossed out ❌.

10. Step 10: Attach Vertical Divider

    Insert 2 dowels (101345) into the top edge of another vertical divider. Align these dowels with the corresponding holes in the base panel and push down. An arrow ▶️ indicates the direction of assembly. The diagram shows dowel 101345 being used and dowel 101339 crossed out ❌.

11. Step 11: Attach Top Panel Dowels

    Insert 8 dowels (101339) into the pre-drilled holes on the top edges of the side panels and vertical dividers. Use a hammer ? to gently tap them in. The diagram shows dowel 101339 being used and dowel 101345 crossed out ❌.

12. Step 12: Attach Top Panel

    Place the top panel onto the assembled unit, aligning the holes with the dowels. Secure the top panel using screws (104322) and the Allen key (100092). The wall bracket (121030) is also secured here.

13. Step 13: Attach Back Panels

    Attach the back panels to the rear of the unit using screws (104332) and the Allen key (100092).

14. Step 14: Attach Decorative Covers

    Attach the 2 hexagonal decorative covers (10002300) to the bottom of the unit. An arrow ▶️ indicates the placement.

15. Step 15: Wall Anchoring - Part 1

    Attach the corner bracket part (115753) to the top of the shelving unit using 2 screws (100372). A warning ⚠️ is shown, indicating the importance of this step. The unit should not be used without wall anchoring. ❌

16. Step 16: Wall Anchoring - Part 2

    Use a spirit level ? to ensure the unit is perfectly vertical before proceeding with wall attachment.

17. Step 17: Wall Anchoring - Part 3

    Attach the wall mounting plate (103693) to the wall at the desired height using appropriate wall fixings (not included). Ensure it is securely fastened.

18. Step 18: Wall Anchoring - Part 4

    Slide the wall anchor bracket (118225) onto the wall mounting plate (103693) attached to the unit. The bracket has adjustable slots for alignment. Secure the bracket by turning the screw mechanism. An arrow ▶️ shows the final insertion.