Reveal Folding Solar Panel

Introduction

Important Safety Instructions

Read and follow all instructions. Save these instructions.

IMPORTANT: Charge this solar panel with the included USB-C charging cable for a minimum of 4 hours before use.

Congratulations on your purchase of the Reveal Folding Solar Panel. Tactacam values your business and strives to provide top-quality customer service. Explore other Tactacam products at www.tactacam.com.

The Reveal Folding Solar Panel is compatible with the following Reveal trail cameras: Ultra, Pro 3.0, X-Gen 3.0, X-Pro, X-Gen 2.0, XB/SK, X, and Gen 1.

This solar panel may be used with devices other than Tactacam trail cameras. If so, carefully check your product manual and contact your device supplier to ensure compatibility before connecting. Tactacam assumes no responsibility for any damage that may occur due to improper use of this product.

Get to Know Your Solar Panel

What's Included

• 1. Solar Panel
• 2. USB-C Cable
• 3. Mounting Strap
• 4. Output Cable

[Diagram of included items: Solar Panel, USB-C Cable, Mounting Strap, Output Cable]

Solar Panel Anatomy

• 1. Solar Panel
• 2. Mounting Bracket
• 3. Battery Level Indicator button
• 4. Battery Light
• 5. Type-C Charging Port
• 6. DC Outlet

[Diagram showing the solar panel with numbered parts: Solar Panel, Mounting Bracket, Battery Level Indicator button, Battery Light, Type-C Charging Port, DC Outlet]

*The side that connects with the power cable should be mounted face down to prevent water ingress from rain.

Other Camera Accessories (Not Included)

[Images of accessories: SD Card, T-Post Mount, Lockable Security Box, Lithium Cartridge, Adjustable Camera Stake]

View and purchase all accessories at tactacam.com.

General Features

• High-efficiency power supply: Converts solar energy into electrical energy and stores it in the internal lithium battery for long-term power.
• Safe and reliable: Designed with short-circuit protection, over-charge protection, and over-discharge protection for battery longevity.
• Environmental protection, energy conservation: Powered by zero-emission, environmentally friendly green solar energy.
• Water-resistant and durable: Rugged IP 66 water-resistant design suitable for outdoor use.
• Easy to use: Features a built-in, sturdy, adjustable, and easy-to-use mount for installation in locations with direct sunlight.
• Battery Indicator: Press the button on the back of the solar panel. Green LEDs indicate approximate power remaining: 4 LEDs = 76-100%; 3 LEDs = 51-75%; 2 LEDs = 26-50%; 1 LED = 1-25%.

Application / Specifications

Application

Provides back-up power for uninterrupted operation of electronic devices such as trail cameras and security cameras.

Specification

Mounting / Operating

Mounting

1. Adjust the angle of the mounting bracket so that the solar panel faces the sun. Generally, in the Northern Hemisphere, this means the panel faces south. The ideal orientation depends on the specific site location. The mounting bracket is adjustable to 30, 60, and 90 degrees.
2. Attach the solar panel to a tree with the included 1.7m strap.

NOTE: The side of the panel that connects with the power cable must face down to prevent water ingress from rain.

[Diagram showing mounting bracket adjustments and strap attachment]

Connecting

Plug one end of the power cable into the output socket (on the right side of the solar panel), and plug the other end into your Tactacam Reveal trail camera. If the internal lithium battery is charged, the camera will be immediately powered.

ATTENTION:

If this solar panel is connected to a Tactacam Reveal camera, it is strongly recommended that batteries be installed in the camera even when connected to the solar charger. Otherwise, the camera may stop operating due to a power shortage. During intensive use of the camera, the solar charger may not charge the camera fast enough, necessitating backup AA batteries or a Reveal Lithium Cartridge.

The solar panel should NEVER be used in a parallel connection with any other power sources. Tactacam is not liable for any damage resulting from incorrect use.

Charging

It is important to completely charge the solar panel for at least 4 hours using the included USB-C charging cable before operating. The charging indicators will illuminate as it charges. Green flashing lights indicate the solar panel is actively charging. When all four lights turn solid green, the solar panel is fully charged.

NOTE: Fully charge the battery at least once every 3 months to optimize battery life and performance.

Precautions

1. Do not scratch the surface of the solar panel.
2. Use the provided cable for charging. Do not use a low-quality or incompatible charging cable or wall charger/adapter, as this could damage the solar panel.
3. If a short circuit protection event occurs, unplug the solar panel and place it in sunlight for 10 seconds. It should then resume normal operation. Alternatively, use the AC adapter to charge and activate the solar panel.
4. Clean the solar panel with a damp soft cloth only. Do not use volatile liquids such as solvents, cleaning fluids, or strong detergents.
5. Do not drop the solar panel.
6. Do not attempt to disassemble or open the solar panel, as this could cause serious damage and void the warranty.
7. Do not expose the solar panel to extreme heat, such as leaving it on a car dashboard in hot weather.
8. Keep the solar panel away from fire.
9. When not in use, disconnect the solar panel from power sources.

FCC Regulations

Federal Communications Commission - Part 15

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the Federal Communications Commission rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.