MCombo 3-Person Swing Chair

Purchaser's Agreement

By accepting delivery of this product, the purchaser agrees not to alter, modify, or remove any safety features. The purchaser also agrees to accept and use any retrofit kits provided by MCombo to maintain the product's safe use.

Contents

• I. Safety Guidelines
• II. Maintenance
• III. Assembly Instructions
• IV. Return / Replacement Policy
• V. MCOMBO Customer Support
• VI. Warranty Disclaimer

I. Safety Guidelines

⚠️ WARNING: For your own safety, please strictly follow the instructions in this manual, otherwise personal injury may result!

Before you proceed, please read the following safety precautions:

• Separate and count all parts and hardware.
• Install not less than 6 feet from any obstruction such as fence, garage, house, overhanging branches, laundry lines, or electrical wires.
• Tighten all nuts and bolts securely. Never use power tools or excessive force during assembly and tightening of bolts.
• Always place the product on a flat, steady, and stable surface.
• It is recommended to protect the swing in case of strong wind or rain and in your absence.
• Do not use candles, matches, or any open flames in or near the swing.

II. Maintenance

• Wash frame parts and fabric with mild soap and water, rinse thoroughly.
• Dry frame completely and allow the fabric to drip dry.
• Do not use bleach, acid, or other solvents on the fabric or frame parts.
• Please inspect and tighten all bolts or fasteners on a regular basis to ensure proper performance and safety of your swing.

III. Assembly Instructions

1. Preparation

Please remove all protective foam. Before assembling, make sure that you lay out and identify all parts listed below in the parts list. Install on level ground.

2. Part List

Frame Part

A: Leg

x4

B: Top Bar (left)

x1

B-1: Ceiling Rotation Base

(preinstalled on part B) x1

C: Top Bar (right)

x1

C-1: Ceiling Rotation Base

(preinstalled on part C) x1

D: Leg Support

x2

E: Connecting Bar

x4

F: Arm Frame (left)

x1

F-1: Arm Frame (right)

x1

G: Seat Frame (front)

x1

H: Seat Frame (back)

x1

I: Seat Cloth

x1

J: Canopy Frame (Right & Left)

x2

J-1: Canopy Rotation Connector

x2

K: Bottom Support (front&back)

x1

L: Bottom Support (left)

x1

L-1: Bottom Support (right)

x1

M: Canopy

x1

N: Seat Cushion

x1

O: Spring Hook

x2

P: Spacer

x2

Q: Knob

x2

Screw Pack

T: M8 x 110 Bolt Set

x4

U: M8 x 75 Bolt Set

x2

V: M8 x 55 Bolt Set

x4

W: M6 x 60 Bolt Set

x8

X: M6 x 40 Bolt Set

x4

Y: M6 x 35 Screw

x4

Z: M6 x 45 Screw

x2

Z-1: M6 x 30 Screw

x1

R: Double-ended Spanner

x1

S: Allen Wrench

x2

Step 1 - Frame Assembly

1. Connect Part B (Left Top Bar) and Part C (Right Top Bar) using two sets of Z (M6*30mm Bolt Set).
2. Connect Part A (Leg) to Part B (Left Top Bar) and Part C (Right Top Bar) respectively, using four sets of T (M8*110mm Bolt Set). The diagram shows legs being attached to the top bars.
3. Connect Part A (Leg) to Part D (Leg Support) using two sets of W (M6*60mm Bolt Set). The diagram shows legs being connected to leg supports.
4. Connect Part L (Left Bottom Support) and Part L-1 (Right Bottom Support) using two sets of Z-1 (M6*30mm Bolt Set). The diagram shows the bottom supports being joined.
5. Connect Part D (Leg Support) and Part L-1 (Right Bottom Support), and Part L (Left Bottom Support) using two sets of V (M8*55mm Bolt Set). The diagram shows the leg supports connecting to the bottom supports.

Step 2 - Seat Assembly

1. Connect Part F-1 (Left Arm Frame) to Part F (Right Arm Frame) and Part G (Front Seat Frame) to Part H (Back Seat Frame) using four sets of Y (M6*35mm Bolt Set). The diagram shows the seat frame components being assembled.
2. Use U (M8*75mm Bolt Set) through P (Spacer) to fix Part I (Seat Cloth) to the seat frame. The diagram shows spacers and bolts attaching the seat cloth to the frame.
3. Attach Part E (Connecting Bar) to Part F (Right Arm Frame) and Part F-1 (Left Arm Frame) using four sets of X (M6*35mm Bolt Set). The diagram shows connecting bars being attached to the arm frames.

Step 3 - Combine Assembly

1. Attach seats to Part B (Left Top Bar) and Part C (Right Top Bar) through O (Spring Hook). The diagram shows spring hooks connecting the seat assembly to the top bars.
2. Attach Part J (Canopy Frame (Right & Left)) to Part B (Left Top Bar) and Part C (Right Top Bar) by Q (Knob). The diagram shows canopy frame pieces being attached to the top bars with knobs.
3. Insert two K (Canopy Frame) into M (Canopy), and connect K (Canopy Frame) to J (Canopy Frame). The diagram shows canopy frame pieces being inserted into the canopy fabric and then connected to the canopy frame.
4. Attach J (Canopy Frame (Right & Left)) to Part B (Left Top Bar) and Part C (Right Top Bar) by Q (Knob). The diagram shows the canopy frame assembly being secured to the top bars.

Step 4 - Flat the Swing

Pull the pull ring on the seat apart and place the backrest flat. The diagram shows a close-up of a pull ring mechanism for adjusting the backrest.

IV. Return / Replacement Policy

MCOMBO offers a 30-day return policy from the date of purchase. Items must be returned in original packaging with all accessories and manuals. Contact sales@mcombo.com or 323-597-1109 to initiate a return. Returns are accepted for items in new, unused condition with original tags. Refunds will be issued in the original form of payment.

V. MCOMBO Customer Support

For questions or suggestions, please refer to the following contact information:

• Email: sales@mcombo.com (Respond within 24 hours)
• Phone: 1-323-597-1109 (8:00 a.m. - 4:00 p.m. PST, Monday - Friday)

Locations:

DE: 2411 Bear Corbitt Rd STE 1, New Castle, DE, 19720

TN: 3980 PREMIER AVE, MEMPHIS, TN, 38118

CA: 2808 Vail Ave, Commerce, CA, 90040

VI. Warranty Disclaimer

Thank you for your interest in the products and services of MCombo. This Limited Warranty applies to physical goods purchased from MCombo.

1. What does this limited warranty cover?

This Limited Warranty covers any defects in material or workmanship under normal use during the Warranty Period. During the Warranty Period, MCombo will repair or replace, at no charge, products or parts of a product that prove defective because of improper material or workmanship, under normal use and maintenance.

2. How long does the coverage last?

The Warranty Period of Physical Goods purchased from MCombo refers to the table below. A replacement Physical Good or part assumes the remaining warranty of the original Physical Good or 180 days from the date of replacement or repair, whichever is longer.

Warranty Exclusions:

This Limited Warranty does not cover any problem that is caused by:

• Conditions, malfunctions, or damage not resulting from defects in material or workmanship.

To obtain warranty service, you can contact MCOMBO via email at sales@mcombo.com. Please provide photos of your product to help determine the issue and the appropriate solution more quickly.