Mcombo 6055-4090 3-Seat Swing Chair

I. About Mcombo

Mcombo's mission is "bringing more convenience to family and travel life." Their vision is "becoming the first choice and trusted brand of customers in outdoor series," with a core value of "providing high-quality and high-standard outdoor products." Mcombo aims to encourage people to engage with outdoor garden life, extend time spent with family and partners outdoors, and enjoy a healthier, more comfortable life.

This user manual is for the 3-seat swing chair, model 6055-4090. Mcombo reserves the right to change or update any content without prior notice. Please read, understand, and follow this manual before assembling and using the swing. Save this manual for future reference. Users are responsible for potential risks of injury due to inappropriate use or failure to obey safety instructions.

II. Safety Guidelines

⚠️ WARNING

For your own safety, please strictly follow the instructions in this manual and adhere to the proper order of assembly. Failure to do so may result in personal injury.

Before proceeding, please read the following safety precautions:

• Separate and count all parts and hardware.
• Install the swing chair at least 6 feet (approx. 1.8 meters) from any obstruction such as fences, garages, houses, overhanging branches, laundry lines, or electrical wires.
• Tighten all nuts and bolts securely. Never use power tools or excessive force during assembly and tightening of bolts.
• Always place the product on a flat, steady, and stable surface.
• It is recommended to secure the product for protection in case of strong wind or rain, and when left unattended.
• Do not use candles, matches, or any open flames in or near the swing chair.

III. Maintenance

• Wash frame parts and fabric with mild soap and water, then rinse thoroughly.
• Dry frame parts completely and allow fabric to drip dry.
• Do not use bleach, acid, or other solvents on the fabric or frame parts.
• Please inspect and tighten all bolts or fasteners on a regular basis to ensure proper performance and safety of your swing chair.

IV. Part List

The following parts and hardware are included:

Parts:

• A: Front Leg (2PCS)
• B: Back Leg (2PCS)
• C: Left Top Bar (1PC)
• D: Right Top Bar (1PC)
• E: Connecting Bar (2PCS)
• F: Rotation Base (preinstalled on part C) (1PC)
• F1: Rotation Base (preinstalled on part D) (1PC)
• G: Left Bottom Support (2PCS)
• G1: Right Bottom Support (2PCS)
• H: Left Back Support (1PC)
• I: Right Back Support (1PC)
• I1: Left Arm Frame (2PCS)
• J: Right Arm Frame with the cloth (2PCS)
• K: Canopy Frame (Right&Left) (2PCS)
• K1: Ceiling Rotation Connector (2PCS)
• L: Lower Canopy Frame (1PC)
• M: Canopy (1PC)
• N: Cushion (1PC)
• O: Left Cup Table (1PC)
• P: Right Cup Table (1PC)

Hardware:

• Q: 8*55mm Bolt Set (6PCS)
• R: 8*65mm Screw (6PCS)
• S: 6*63mm Bolt Set (2PCS)
• T: 8*72mm Bolt Set (4PCS)
• W: 6*32mm Bolt Set (3PCS)
• X: Knob (2PCS)
• Allen Wrench (1PC)
• Double-ended Spanner (1PC)

V. Assembly Steps

1. Preparation: Remove all protective foam. Before assembling, ensure all parts are laid out and identified. Install the swing chair on level ground.
2. Connect the two Connecting Bars (E) to the two Front Legs (A) and the two Back Legs (B) using four 8*65mm Screws (R).
3. Insert the Left Top Bar (C) into the Right Top Bar (D) using two 8*55mm Bolt Sets (Q). Then, connect the Front Legs (A), Back Legs (B) to the assembled Top Bars (C and D) using four 8*55mm Bolt Sets (Q).
4. Connect the Left Back Support (H) to the Right Back Support (I). Connect the two Left Bottom Supports (G) to the two Right Bottom Supports (G1) using three 6*32mm Bolt Sets (W). Attach the ends of these three assembled support rods to the Left Top Bar (C) and Right Top Bar (D) using six 8*65mm Screws (R).
5. Attach the Left Cup Table (O) and the Right Cup Table (P) to the Front Leg (A) using two 6*63mm Bolt Sets (S).
6. Attach the two Left Arm Frames (I1) and the two Right Arm Frames (J) to the Seat Frame (N) using four 8*72mm Bolt Sets (T).
7. Attach the Left Arm Frame (I1) and the Right Arm Frame (J) to the Left Top Bar (C) and Right Top Bar (D) using the Spring Hooks (K).
8. Attach the Canopy Frames (K) to the Left Top Bar (C) and Right Top Bar (D) using the Knobs (X). Tip: Do not fully tighten the Knobs (X) until the entire installation is complete.
9. Connect the Canopy Frames (K) to the Lower Canopy Frame (L).
10. Insert the Lower Canopy Frame (L) into the Canopy (M).
11. Place the Cushion (N) onto the seat.
12. To recline the backrest, pull the pull ring on the Right Arm Frame (J) to separate it from the seat frame, allowing the backrest to lay flat.

Congratulations, your swing chair has been installed. ?

VI. Warranty Disclaimer

Thank you for your interest in the products and services of Mcombo. This Limited Warranty applies to physical goods purchased from Mcombo.

What does this limited warranty cover?

This Limited Warranty covers any defects in material or workmanship under normal use during the Warranty Period. During the Warranty Period, Mcombo will repair or replace, at no charge, products or parts that prove defective due to improper material or workmanship, under normal use and maintenance.

How long does the coverage last?

The Warranty Period for Physical Goods purchased from Mcombo is as follows:

A replacement Physical Good or part assumes the remaining warranty of the original item or 180 days from the date of replacement or repair, whichever is longer.

This Limited Warranty does not cover any problem caused by conditions, malfunctions, or damage not resulting from defects in material or workmanship.

To obtain warranty service, contact Mcombo via email at sales@mcombo.com to determine the issue and the appropriate solution. Providing photos of your product can help expedite the process.

VII. Return/Replacement Policy

Mcombo offers a 30-day return/replacement policy for all items. During this period, Mcombo will cover the shipping cost for returns and replacements of defective or damaged items by providing a pre-paid return label or arranging a pick-up service for customer convenience.

Please disassemble the item before returning it, unless doing so would incur significant costs due to its oversized nature.

Mcombo is not responsible for returns due to customer mistakes, change of mind, or other non-quality-related issues. The customer is responsible for freight costs unless the item is defective.

Items returned due to refusal by the customer or deemed undeliverable by the freight carrier are subject to fees for freight in both directions and a 15% restocking fee.