Endorfy Regnum 400 Air PC Case

Accessories Included

The following accessories are provided with the Endorfy Regnum 400 Air PC case:

• A: Motherboard Standoffs (x13)
• B: SSD Screws (x22)
• C: Case Screws (x6)
• D: HDD Screws (x20)
• E: Fan Screws (x6)
• F: PSU Screws (x1)
• G: Zip Ties (x3)
• Fans: Stratus 120 PWM (pre-installed)
• PWM Splitter: 5x PWM 4-PIN connectors
• Storage Mounts: 2x 2.5"/3.5" Hybrid Drive Bays, 2x 2.5" SSD Mounts
• Maximum PSU Length: 296 mm

1. Overview

This section provides an overview of the PC case layout and component support:

• Top Panel: Supports up to two 120/140mm fans or a 120mm radiator.
• Front Panel: Features a mesh front for airflow. Supports up to three 120mm fans or two 140mm fans, and radiators up to 120/240/280/360mm.
• Rear Panel: Supports one 120mm fan.
• Bottom Panel: Includes a PSU filter. The maximum supported PSU length is 296mm.
• I/O Panel: Located on the top panel. Connect the I/O cables to your motherboard according to your motherboard manual. Ports include: Power button, Power LED, HDD LED, Reset button, Microphone port, Headphones port, and two USB ports.

2. Panel Removal

Visual guide showing how to remove the side panels of the PC case to access the interior for installation.

3. Hardware Installation: Motherboard

Install motherboard standoffs (A) into the case chassis at the appropriate positions for your motherboard. Place the motherboard onto the installed standoffs and secure it with screws.

4. Hardware Installation: PSU and Expansion Cards

Install the Power Supply Unit (PSU) into the bottom compartment and secure it with screws (F). Install expansion cards (e.g., graphics card) into the motherboard's expansion slots and secure them. Use parts (A) and (B) as indicated for securing various components.

5. Hardware Installation: Storage Devices

• SSD Installation: Mount 2.5-inch SSDs in the designated SSD bays using screws (B).
• HDD Installation: Mount 3.5-inch HDDs in the designated HDD bays using screws (D) and brackets (F).

6. Dust Filters

Visual guide showing the installation of dust filters at the bottom and top of the case to help maintain internal cleanliness.

7. Fan Connection

Connect the PWM 4-PIN fan cables to the motherboard's fan headers or to the provided PWM splitter. The splitter can then connect to the motherboard's CHA_FAN header for centralized fan control.

Safety Instructions

Please read the following safety instructions carefully before using the product:

1. The product should be used as intended. Incorrect use may damage the product and be dangerous to your health.
2. Make sure that the product is in good working order before using it.
3. The warranty does not cover mechanical damage to the product.
4. This device is intended for indoor use, under normal humidity conditions. Do not use it outdoors.
5. Do not install and use the device within reach of children.
6. To prevent damage from condensation, allow the device to warm up to ambient temperature before use.
7. Clean only with a dry, clean cloth. Do not handle with wet hands.
8. No user-serviceable components inside. Return to authorized service center for repairs.
9. Do not use the product near liquids or in places where it may be directly exposed to liquids. If the device comes into contact with any liquids, immediately disconnect it from the power source.
10. In the event of a malfunction, disconnect it from the power source immediately and contact ENDORFY Technical Support.
11. Do not discard electrical and electronic equipment together with other household waste.
12. The end user is responsible for correct disposal of unnecessary or faulty electrical equipment by returning it to the collection point or to the seller. Contact local authorities or the store where you purchased the product for additional information.

Environmental Disposal Information: This symbol indicates that this product and its battery (if included) should not be disposed of with other household waste. At the end of its life, the product should be taken to a special collection point designated by the relevant local authorities. The separate collection and recycling of products and batteries helps to save natural resources and ensures that the recycling process is safe for human health and the environment.

For more information, visit endorfy.com.