Endorfy Ventum 200 ARGB PC Case

Accessories

The following accessories are included with the Ventum 200 ARGB PC case:

• ZIP TIE x6
• PCI BRACKET x1
• Fans (pre-installed)
• STRATUS 120 STACKED SPLITTER
• 5x PWM 4-PIN connectors
• 5x ARGB 3-PIN connectors
• 1x 2.5"/3.5" (HYBRID) drive bay
• 2x 2.5" (SSD) drive bays

1. Overview

This section provides an overview of the PC case components and their specifications:

• REAR: Designed for one 120mm fan.
• TOP: Supports two 120mm fans or one 120mm fan/radiator.
• BOTTOM: Maximum PSU clearance is 180 mm. Features a PSU filter.
• FRONT: Supports three 120mm fans or two 140mm fans. Compatible with 120/240/280/360mm radiators. Features a mesh front panel for airflow.
• I/O Ports: Located at the top of the case.

Note: To connect the I/O panel of the case to your motherboard, please refer to your motherboard manual.

The top I/O panel includes:

1. Power button
2. Power LED
3. HDD LED
4. Reset button
5. USB port
6. Headphones port
7. Microphone port
8. USB port

2. Panel Removal

This step illustrates the process of removing the case panels, typically the side panels, to access the interior for hardware installation.

3. Hardware Installation (Motherboard)

This step guides the installation of the motherboard. It shows the use of screws (A) for mounting the motherboard, likely onto standoffs.

4. Hardware Installation (PSU)

This step details the installation of the Power Supply Unit (PSU). It indicates using four (A) screws for PSU mounting, noting that these screws should be included with the PSU.

5. Hardware Installation (Drives)

This section guides the installation of storage drives, specifically SSDs and HDDs.

• SSD Mounting: Shows mounting 2.5" SSDs using screws (D) in the top view area. Brackets (E+F or E+G) are used for securing SSDs.
• HDD Mounting: Shows mounting 3.5" HDDs using screws (G) in the bottom view area.
• Additional Mounting: Bracket (H) is shown for a specific mounting purpose.

6. Dust Filters

This step shows the location and likely installation or cleaning of dust filters, typically found at the bottom of the case to prevent dust ingress.

7. Illumination and Fan Connection

This section explains how to connect the case fans and ARGB lighting components.

• ARGB 3-PIN (5V): Connects to ARGB headers on the motherboard or a compatible controller for RGB lighting effects.
• PWM 4-PIN: Connects to PWM fan headers on the motherboard for intelligent fan speed control based on temperature.
• SATA: Connects to the PSU for power supply to lighting components or fan hubs.

Connection options are presented: "Motherboard effect" (syncing with motherboard RGB software), "Built-in effect" (using pre-programmed lighting patterns), or "No illumination".

Safety Instructions

Please read and follow these safety instructions carefully:

1. The product should be used as intended. Incorrect use may damage the product and be dangerous to your health.
2. Make sure that the product is in good working order before using it.
3. The warranty does not cover mechanical damage to the product.
4. This device is intended for indoor use, under normal humidity conditions. Do not use it outdoors.
5. Do not install and use the device within reach of children.
6. To prevent damage from condensation, allow the device to warm up to ambient temperature before use.
7. Clean only with a dry, clean cloth. Do not handle with wet hands.
8. No user-serviceable components inside. Return to authorized service center for repairs.
9. Do not use the product near liquids or in places where it may be directly exposed to liquids. If the device comes into contact with any liquids, immediately disconnect it from the power source.
10. In the event of a malfunction, disconnect it from the power source immediately and contact ENDORFY Technical Support.
11. Do not discard electrical and electronic equipment together with other household waste.
12. The end user is responsible for correct disposal of unnecessary or faulty electrical equipment by returning it to the collection point or to the seller. Contact local authorities or the store where you purchased the product for additional information.

Environmental Disposal: The symbol ♻️ indicates that this product and its battery (if included) should not be disposed of with other household waste. At the end of its life, the product should be taken to a special collection point designated by the relevant local authorities. The separate collection and recycling of products and batteries helps to save natural resources and ensures that the recycling process is safe for human health and the environment.