Blaupunkt BP S3000 Smart Doorbell

Package Contents

Please check and ensure the device is in good condition and all listed parts are included in the package after opening it:

• Device (including mounting bracket)
• Security screw
• Quick Start Guideline
• Two 21700 batteries

Product Overview

The Blaupunkt BP S3000 is a smart, waterproof video doorbell.

Device Components:

• 1. Light Sensor: Detects ambient light levels.
• 2. Camera: Captures video.
• 3. PIR Motion Sensor: Detects motion.
• 4. Speaker: For two-way audio.
• 5. Doorbell Button: The button to ring the doorbell.
• 6. LED Indicator: Shows device status.
• 7. Microphone: For capturing audio.
• 8. Memory Card Slot: For external storage (up to 128GB).
• 9. Reset Button: Used to reset the device.
• 10. Power Button: Turns the device on/off.
• 11. Charging Indicator: Shows charging status.
• 12. Micro USB Port: For charging the device.
• 13. Security Screw Hole: For securing the device.
• 14. Wiring Terminals: For wired installation.
• 15. Mounting Holes: For attaching to a wall.
• 16. (Diagram component): Not explicitly described in text, likely part of the mounting bracket.

Technical Specifications

Installation

Mounting the Camera to the Wall

Note: For optimal performance and to avoid interference, follow these guidelines:

• Do not install near heat sources like air conditioners or kitchen vents.
• Ensure no reflections are within 1.5 meters of the PIR sensor.
• Avoid installing next to busy roads to minimize false alerts from frequent motion.
• Install within good Wi-Fi range of your router.

Tools Needed:

• Drill

Step 1: Choose Location

Select a mounting location. Use the app's installation guide to check Wi-Fi signal strength at the chosen spot. Ensure a strong Wi-Fi signal for smooth operation.

Step 2: Mount the Bracket

Use a drill to attach the mounting bracket to the wall. It is recommended to mount it at a height of 120 cm (approx. 47 inches) from the ground. Slide the camera onto the bracket and secure it with the security screw.

Step 1: Wired Installation (Optional)

To replace your existing doorbell and mechanical chime, follow these steps:

1. Turn off the main power switch to your home.
2. Install a bypass for your existing doorbell using the included bypass switch.
3. Remove the cover of your existing doorbell and disconnect the wires (Front and Trans terminals). Use the included bypass switch to connect the two terminals, then reassemble the doorbell cover.
4. Connect the wires to the terminals on the mounting bracket. The order of the wires does not matter.
5. Secure the mounting bracket to the wall using the included screws or double-sided tape.
6. Reinstall the doorbell.
7. Restore power at the main switch. Your doorbell is ready to use.

Step 2: Wireless Installation

1. Release the mounting bracket from the doorbell using the included Allen key.
2. Mark the hole positions and attach the bracket to the wall using screws.
3. Alternatively, use the included double-sided tape to mount the bracket on flat surfaces.
4. Attach the doorbell to the bracket after mounting.
5. Tighten the security screw at the bottom of the bracket.
6. Test the doorbell by pressing the button.

Connecting the Device

1. Adding a Device (QR Code Pairing Mode)

Quick Wi-Fi Connection (Default Mode): On the device list page, tap 'Add Device' in the center or the '+' button in the top right corner to enter the device addition page. This page offers two methods: manual addition and automatic discovery. Use the manual addition mode.

2. Registration, Login, and Password Reset

Registration: Open the Tuya Smart app and tap 'Sign Up'. Read the User Agreement and Privacy Policy carefully and tap 'Agree' to proceed to the registration page. Enter your mobile number or email and tap 'Get Verification Code'. The country/region should match your phone's settings, but you can change it manually. Enter the verification code and set a password. Tap 'Done'.

Login: Open the TuyaSmart app and tap 'Log In'. Review the User Agreement and Privacy Policy, then tap 'Agree'. Verify your country/region (it usually auto-detects). Enter your registered mobile number/email and password, then tap 'Log In'.

Password Reset: On the login page, tap 'Forgot Password'. On the page that appears, verify your country/region. Enter your registered mobile number or email and tap 'Get Verification Code'. Enter the verification code and set a new password, then tap 'Done'.

Connecting via QR Code:

1. After tapping 'Next' in the Wi-Fi setup, you will proceed to the Wi-Fi password page.
2. Display the QR code directly to the camera, maintaining a distance of 15-20 cm, until you hear a beep from the camera.
3. If you don't hear a beep, tap 'I Heard a Prompt' to proceed to the device addition page.

5. Successful Connection

If the network setup is successful, the following page will appear. You can rename the camera. Tap 'Done' to proceed to the device operation page.

6. Device Operation

You can rename the camera. Tap 'Done' to enter the device operation page.

Wireless Doorbell Setup

Important Notes:

• The device is powered by a lithium-polymer battery, providing 5-8 months of use on a full charge. The app will notify you when the battery is low.
• Ensure the device has a stable Wi-Fi connection, especially for outdoor installations. Use a Wi-Fi extender if the signal is weak.
• This is a smart, low-power device supporting app control, motion detection (PIR), and doorbell ringing. It enters sleep mode automatically and wakes up upon activity, operating for 30 seconds after activation.

Getting Started

Pair the wireless doorbell with the video doorbell.

Step 1

Before setup, ensure the video doorbell is connected to your phone and the wireless doorbell.

Step 2: Select Chime Melody

Press the melody button to cycle through 52 different melodies and select one.

Step 3: Adjust Volume

Press and hold the volume button for 5 seconds until the blue indicator lights up.

Step 4: Ring the Doorbell

Press the ring button.

Step 5: Test the Chime

Press the ring button again. The doorbell will automatically play the selected melody.

Frequently Asked Questions (FAQs)

Q: The device cannot connect to Wi-Fi?

A:

• Ensure your wireless network is connected.
• Check if the indicator light is flashing slowly with a red light.
• Verify that the password is correct and has no extra spaces.

Q: The device is online and an event occurs, but the mobile phone does not receive a push notification.

A: Ensure the app has enabled 'Self-start' and notifications according to app permissions. Check 'Battery Optimization' and app termination settings when the phone is in standby mode (phone manufacturer's battery optimization may vary; refer to your phone's standard settings).

Q: What power supply modes does the device support?

A:

• The device can operate with two 21700 batteries (in the doorbell).
• You can charge the device via USB.

Tip: There will be no notifications for changes to the above functions. Refer to the doorbell in your hand as the standard.

Warranty Information

This warranty certificate is for the product's functionality. Blaupunkt Technologies Ltd. warrants to repair the product within 10 business days of its arrival at the company's service center, or replace the product or any part thereof if necessary, free of charge. If replacement parts are required for repair, new and original parts will be used. The warranty period is 12 months from the date of purchase and is valid only when accompanied by a purchase invoice from a supplier authorized by us. If there is no service point within 15 km of the store where the purchase was made, the consumer may bring the product for repair at the store where it was purchased, and the repair will be completed within two weeks of the product's delivery. After the repair and/or replacement, the consumer will receive a written confirmation detailing the nature of the repair and/or replacement. We reserve the right to charge for repairs if the defect is caused by:

• Improper use of the product (e.g., connecting headphones to an incompatible power source).
• Intentional damage or negligence by the consumer (e.g., damage from battery leakage, contamination with sand, dust, water, oil, etc., or breakage of the product).
• Repairs performed by unauthorized personnel.
• Force majeure events occurring after the product's delivery.

Importer Details: Blaupunkt Technologies Ltd., Company No. 514849371. P.O. Box 50 Kiryat Ekron, Bilu Center IN. Phone: 08-9418222 Fax: 08-9418223. Email: info@bconnect.co.il. Website: www.bconnect.co.il. Customer Service and Technical Support: 08-9403300. Central Service Point and Laboratory: 08-9418222.

Service Points List: (Details of service points in various cities are provided in the original document).