Blaupunkt DC-S4 / DC-S4B Door/Window Detector
White/Brown
Diagram and Components
The document includes a diagram illustrating the Blaupunkt DC-S4/DC-S4B Door/Window Detector and its components. The main detector unit features:
- 1. LED Indicator / Learn Button: Used for status indication and device pairing.
- 2. Knockouts: Pre-scored points on the unit for screw mounting.
- 3. Battery Insulator: A tab to be removed to activate the battery upon first use.
- 4. Rib Mark: A visual guide for aligning the magnet during installation.
- 5. Magnet: A separate component that works with the detector to sense when a door or window is opened.
- 6. Tamper: A switch that triggers an alert if the detector unit is opened or tampered with.
The diagram also shows the typical installation setup, where the main detector unit is mounted on the door or window frame, and the magnet is mounted on the door or window itself. The maximum recommended gap between the detector and the magnet when the door/window is closed is 15 mm.
Getting Started
Follow the instructions in this document to set up and use the accessory. For detailed settings and operation, visit the Blaupunkt website at service.blaupunkt-security.com to download the complete manual.
Registration
- Pull out the battery insulator to activate the battery.
- For Q Series: Go to the Web Portal https://eu.bphomeconnect.com/BP/ and log in with your account credentials.
- Put the Hub into learning mode: Navigate to Settings → Device and click the "+ Add device" button.
- Press the Learn Button (1) to learn-in the DC-S4. When the panel receives the "learn signal", it will emit a double beep, and the web interface will display the device information.
- Check the box in front of the device information, then click OK to add the device into the system.
- Input a name for the device (e.g., "Front Door Contact") and select the desired zone.
- To change the accessory's attribute, click the 3 dots on the right side of the accessory and select the desired attribute (e.g., burglar, entry, home omit) from the attribute pull-down menu.
Note: For SA series, refer to the panel manual to learn how to register a device.
Installation Location
- Mount the main body of the door contact on the door/window frame, and the magnet on the door/window.
- Install the detector at the highest part of the door/window.
- Do not aim a PIR Movement Detector at this door/window.
- Do not install on doors or windows with magnetic surfaces like iron or steel.
Installation
Screw Installation
- Remove the back cover and push through the 2 knockouts on the back (where the plastic is thinner) using a screwdriver.
- Drill 2 holes into the surface using the knockouts as a template.
- Fix the detector's back cover onto the surface with the provided screws and plugs.
- Reattach the main body to the back cover and screw it back on.
Magnet Installation
- Align the magnet with the Rib Mark (item #4) on the main body.
- Ensure the gap between the main body and the magnet is no more than 15 mm.
- Fix the magnet onto the door/window using the provided double-sided tape.
Alternative Installation: The main body can also be installed using the included double-sided adhesive tape instead of screws.
Tamper Protection: Ensure the tamper protection is pressed against the door/window surface to prevent tamper alerts.
Supervision Mode: This accessory does not have a supervision mode.
Technical Specifications
| Specification | Value |
|---|---|
| Battery brand | Lithium CR2032/3V |
| Standby power consumption | 5uA |
| Max. power consumption | 15mA |
| Radio frequency | 868.35Mhz |
| Max. Transmission power | 7dBm |
| Duty cycle | At 868.3 MHz < 1% per h |
Declaration of Conformity
Security Brand Pro GmbH hereby declares that the radio equipment type "DC-S4" complies with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at: www.blaupunkt.com/service
Disposal
Old appliances must not be disposed of with normal household waste. In accordance with Directive 2012/19/EU, the device must be disposed of properly at the end of its service life. Recyclable materials are recycled to avoid environmental pollution. Return old devices free of charge to a collection point for electrical waste or a recycling yard. Used batteries must be collected separately and disposed of in an environmentally sound way (European Directive on Electrical and electronic equipment).
Dispose of packaging materials in an environmentally friendly manner by placing them in the provided collection containers.
General recycling symbol: Further information can be found at www.mueller-licht.de/recycle/
🌿 Green Dot
