WALI Universal Table Top TV Stand

Unpacking Instructions

• Carefully open the carton, remove contents, and lay them out on a cardboard or other protective surface to avoid damage.
• Check package contents against the Supplied Parts List to ensure all components were received undamaged. Do not use damaged or defective parts.
• Carefully read all instructions before attempting installation.

Important Safety Information

• Install and operate this device with care. Please read this instruction before installation and carefully follow all instructions contained herein. Use proper safety equipment during installation.
• Please call a qualified installation contractor for help if you do not understand these directions or have any doubts about the safety of the installation.

Do not use this product for any purpose or in any configuration not explicitly specified in this instruction. WALI disclaims any and all liability for injury or damage arising from incorrect assembly, incorrect mounting, or incorrect use of this product.

Supplied Parts List

The following parts are included in the package:

• Base Plate-A1 (1)
• Junction Plate-A2 (1)
• Plastic Cover-A3 (1)
• TV Bracket1-A4 (1)
• TV Bracket2-A5 (1)
• Base Plate-B1 (1)
• Junction Plate-B2 (1)
• Plastic Cover-B3 (1)
• TV Bracket1-B4 (1)
• TV Bracket2-B5 (1)
• M6x10 Bolt-C (Allen Head) (8)
• M6 Nut1-D (4)
• M6 Nut2-E (4)
• Allen Key-F (1)
• Wrench-G (1)
• M4x12 Bolt-H (4)
• M4x30 Bolt-I (4)
• M6x20 Bolt-J (4)
• M6x35 Bolt-K (4)
• M8x20 Bolt-L (4)
• M8x35 Bolt-M (4)
• M4 Washer-N (4)
• M6 Washer-O (4)
• M8 Washer-P (4)
• M4 Spacer-Q (4)
• M6/M8 Spacer-R (8)

Installation Steps

Step 1: Connecting the Base Plates and Junction Plates

Connect the Base Plates (A1, B1) to the Junction Plates (A2, B2) using the M6x10 Bolts (C) and the Allen Key (F).

Diagram shows Base Plate A1 and Junction Plate A2 being joined by Bolt C, secured with Allen Key F. Similarly, Base Plate B1 and Junction Plate B2 are shown connected.

Step 2: Connecting the Vertical Monitor Brackets

Attach the Vertical Monitor Brackets (A4, A5, B4, B5) to the assembled base and junction plate structures. Use the provided Bolts (E) and Washers (G) for this connection.

Diagram illustrates Vertical Monitor Brackets A4 and A5 being attached to the structure, secured by Bolts E and Washers G. The same is shown for B4 and B5.

Step 3: Connecting the TV Brackets and Junction Plates, then install the Plastic Covers

Connect the TV Brackets (A4, A5, B4, B5) to the Junction Plates (A2, B2) using Bolts (C) and Washers (G). After securing the brackets, install the Plastic Covers (A3, B3) over the connection points.

Diagram shows TV Brackets A4 and A5 connecting to Junction Plate A2 with Bolt C and Washer G. Plastic Cover A3 is then shown being fitted. The same process is depicted for B4, B5, B2, and B3.

Step 4: Attaching the TV Brackets to the back of TV

First, ensure you select the correct diameter and length of Bolts (H, I, J, K, L, M) that fit your TV's VESA mounting holes. Thread the selected Bolts into the TV using the appropriate Washers (N, O, P). Use the Spacers (Q, R) only if the bolts are too long for a secure fit.

Diagram shows a TV back with VESA holes. Bolts (H to M) and Washers (N to P) are shown ready for insertion. Spacers (Q, R) are also depicted, indicating their use when bolts are too long.