Important Safety Information
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. WALI cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
! TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER.
TO HELP PREVENT TIPOVER:
- NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
- USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL.
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIP OVER.
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
Supplied Parts List
- Arm A (x2)
- Holder B (x2)
- Spacer C (x2)
- Spacer D (x4)
- Nut E (x4)
- Screw F (x4)
- Wrench G (x1)
- M5x16 Bolt M-A (x4)
- M6x16 Bolt M-B (x4)
- M5x25 Bolt M-C (x4)
- M6x25 Bolt M-D (x4)
- M6x40 Bolt M-E (x4)
- M8x40 Bolt M-F (x4)
- M8x60 Bolt M-G (x4)
- D5 Washer M-H (x4)
- Spacer M-I (x8)
- Spacer M-J (x8)
Installation Options
Choose one of the following installation options:
- Below The TV: Refer to pages 4-7 for instructions.
- Above The TV: Refer to pages 8-10 for instructions.
Option A: Below The TV
Step 1: Attach Holder to Arms
Attach the Holder (B) to the Arms (A). Screw Holder (B) into the preferred key slots on Arm (A) with Nut (E) and tighten using Wrench (G).
Diagram Description: Shows Holder B being attached to Arm A using Nut E and Wrench G.
Step 2.1: Ensure Ample Room for Speaker
Measure the speaker height before installation. Ensure there is adequate clearance ('a') for the soundbar.
Diagram Description: Illustrates a soundbar with clearance measurements 'a' needed. Also shows a TV with mounting holes and the concept of checking screw fit.
Step 2.2: Select Correct TV Mounting Screws
Manually thread screws (M5, M6, or M8) into the mounting holes on the back of your TV to determine the correct size that fits.
Diagram Description: Shows M5, M6, and M8 screws. Demonstrates testing screw fit in TV mounting holes, indicating correct and incorrect fits.
Step 2.3: Attach Soundbar Brackets to TV
Attach the soundbar brackets to your TV using the appropriate screws (M-A, M-B, M-E, M-F, M-G, M-H, M-I, M-J) and spacers as shown in the diagrams.
Diagram Description: Detailed illustration of attaching the bracket arms to the TV using various combinations of screws and spacers.
Step 3: Adjust and Secure Soundbar
1. Adjust the holder according to the depth of your soundbar.
2. Tighten the knobs to ensure the soundbar is sitting securely.
Diagram Description: Shows adjusting the holder depth and then tightening knobs to secure the soundbar in place.
Option B: Above The TV
Step 1: Attach Holder to Arms
Attach the Holder (B) to the Arms (A). Screw Holder (B) into the preferred key slots on Arm (A) with Nut (E) and tighten using Wrench (G).
Diagram Description: Shows Holder B being attached to Arm A using Nut E and Wrench G.
Step 2.1: Ensure Ample Room Between Holder and TV
When mounting the soundbar above the TV, ensure there is ample room (greater than 5mm) between the bracket and the TV.
Diagram Description: Illustrates the TV and bracket mounted above, showing the required clearance of more than 5mm.
Step 2.2: Select Correct TV Mounting Screws
Manually thread screws (M5, M6, or M8) into the mounting holes on the back of your TV to determine the correct size that fits.
Diagram Description: Shows M5, M6, and M8 screws. Demonstrates testing screw fit in TV mounting holes, indicating correct and incorrect fits.
Step 2.3: Attach Soundbar Brackets to TV
Attach the soundbar brackets to your TV using the appropriate screws (M-C, M-D, M-E, M-F, M-G, M-H, M-I, M-J) and spacers as shown in the diagrams.
Diagram Description: Detailed illustration of attaching the bracket arms to the TV using various combinations of screws and spacers for the 'above TV' configuration.
Step 3: Adjust and Secure Soundbar
1. Adjust the holder according to the depth of your soundbar.
2. Tighten the knobs to ensure the soundbar is sitting securely.
Diagram Description: Shows adjusting the holder depth and then tightening knobs to secure the soundbar in place.
Customer Support
WALI supports the technology that brings your home to life. WALI offers high quality products, professional customer service, and extensive technical support.
If you have any questions, please contact WALI:
Phone: 1-844-SATTLER (18447288537)
Email: support@walielectric.com
