Latitude Run 1 Corner Seat + 1 Single Seat Assembly Instructions

Notice

Please keep these instructions for future reference.

Dear Customer

Thank you for your purchase. When you receive the product, please make sure that all the parts are intact. Then follow the entire installation instructions to install!

There is an installation video on the product page. You can open the product page to view it or contact customer service to receive it.

Potential Issues and Solutions:

• A. The outer box is damaged
• B. The product is damaged / bent / cracked while you open the box
• C. The parts / accessories / assembly tools are missing
• D. The instructions are not clear and can not be referred
• E. The product has functional problems
• F. Other aspects that you are not satisfied with

Please feel free to contact Latitude Run customer service for help, and provide the following information: Platform/Shop name, Order ID, Buyer's name, Receiver's address, Problem description.

Part List

The following parts are included in the package:

• Part A: Corner Seat Base Structure
• Part B: Single Seat Base Structure
• Part C: Side Panel (x2)
• Part D: Legs (x8 total, 4 per base)
• Part E: Seat Cushion (x2)
• Part F: Back Cushion (x2)
• Part N: Buckle/Connector (x2)

Hardware:

• Screw 1 (M6*15MM): x12
• Screw 2 (M6*30MM): x8
• Gasket (3): x20
• Tool 6: Allen Key (x1)

Assembly Steps

Step 1: Attach Legs to Corner Seat Base (Part A)

Place Screw 1 (M6*15MM) through the designated hole. Hold the screw in place with Tool 6 (Allen Key). Rotate the bottom of Part D (Leg) against Screw 1 to hold it in place at a 90% angle.

[Diagram Description: Shows Part A (base), Screw 1, Gasket 3, Part D (leg), and Tool 6. An enlarged view shows the screw insertion and leg attachment with rotational arrows.]

Step 2: Secure Legs to Corner Seat Base (Part A)

After initial tightening of the screws, proceed to tighten the bottom screws securing the legs (Part D) to Part A.

[Diagram Description: Shows Part A with all 4 legs attached and screws tightened.]

Step 3: Attach Side Panel (Part C) to Corner Seat Base (Part A)

Align holes by placing Part C (Side Panel) under Part A (Base) to make installation easier. Tighten the screws (Screw 1 and Gasket 3) 40% to proceed to the next step.

[Diagram Description: Shows Part C being attached to Part A using screws and gaskets. An enlarged view shows the alignment and screw insertion.]

Step 4: Final Tightening for Corner Seat

Tighten screws 40% and all screws when finished for the corner seat assembly.

[Diagram Description: Shows Part A with Part C attached, screws tightened.]

Step 5: Attach Legs to Single Seat Base (Part B)

Place Screw 1 (M6*15MM) through the designated hole. Hold the screw in place with Tool 6 (Allen Key). Rotate the bottom of Part D (Leg) against Screw 1 to hold it in place at a 90% angle.

[Diagram Description: Similar to Step 1, but showing Part B (base) and Part D (legs).]

Step 6: Secure Legs to Single Seat Base (Part B)

After initial tightening of the screws, proceed to tighten the bottom screws securing the legs (Part D) to Part B.

[Diagram Description: Shows Part B with all 4 legs attached and screws tightened.]

Step 7: Attach Side Panel (Part C) to Single Seat Base (Part B)

Align holes by placing Part C (Side Panel) under Part B (Base) to make installation easier. Tighten the screws (Screw 2 and Gasket 3) 40% to proceed to the next step.

[Diagram Description: Shows Part C being attached to Part B using screws and gaskets. An enlarged view shows the alignment and screw insertion.]

Step 8: Final Tightening for Single Seat (using Screw 2)

Tighten screws 40% and all screws when finished for the single seat assembly.

[Diagram Description: Shows Part B with Part C attached, screws tightened.]

Step 9: Attach Second Side Panel (Part C) to Single Seat Base (Part B)

Rotate the product to find a new hole position and repeat the previous step (attaching Part C to Part B using Screw 2 and Gasket 3).

[Diagram Description: Shows the second Part C being attached to Part B using Screw 2 and Gasket 3.]

Step 10: Final Tightening for Single Seat (using Screw 2)

Tighten screws 40% and all screws when finished for the single seat assembly.

[Diagram Description: Shows Part B with both Part Cs attached, screws tightened.]

Completing the Installation

The assembly of the corner seat and single seat is now complete. Add cushions (Part E and F) as needed.

[Diagram Description: Shows the assembled corner seat and single seat.]

Tips

1. In order to increase the toughness of the sofa fixed buckle (Part N), please soak it in hot water for 10 minutes before use.
2. When in use, first snap one side of the buckle (Part N) into the metal frame, and then force the other side into the frame.
3. You can freely make a variety of combinations using the above methods.

[Diagram Description: Shows Part N (buckle) being soaked in water, and then being attached to a frame.]

After-Sale Service

If you have any suggestions for Latitude Run products or find that the products have quality problems, please contact Latitude Run customer service first. The after-sales team will reply within 24 hours and will do their best to provide solutions until you are satisfied.

Guaranteed Customer Service

Your shopping experience is very important. If you are unsatisfied or have any questions, please contact Latitude Run customer service.

Share your pictures and suggestions with Latitude Run.