Signature Design by Ashley Bunk Bed Assembly Instructions

Important Safety Notice

Read Carefully Before Beginning Assembly!

• Always use proper tools.
• Follow the assembly steps in order. Do not skip any steps.
• Check all packing materials carefully for small parts that may have come loose. If parts are missing, contact the retailer. DO NOT USE SUBSTITUTE PARTS.
• Periodically check to ensure all connectors (bolts, screws, etc.) are tight.
• Keep instructions for future reference.
• Handle glass or mirrors with extreme care. Never handle large pieces of glass or mirrors alone.
• When assembling products with electric cords, ensure the cord is unplugged before assembly and be careful not to twist the cord.
• Do not stand on lower shelves when assembling upper shelves; use a step ladder.
• Do not stand on tables, as they are not designed to support a person's weight.
• If assembly requires two or more people, do not attempt alone due to risk of injury.

Note: Ashley Furniture Industries, LLC disclaims liability for damages or injuries due to failure to follow assembly instructions, improper assembly, or improper use of the product.

Note: Your unit may look different from the illustrations.

Safety Warnings

For Bunk Bed Use:

• Assembly should be performed by two or more adults. Allow 60 minutes for assembly.
• DO NOT TIGHTEN ANY BOLTS UNTIL ALL BOLTS HAVE BEEN STARTED.
• Replacement parts, including additional guardrails, may be obtained from Ashley Furniture dealers or by calling 1-800-477-2222.
• WARNING LABEL: DO NOT REMOVE!
• MODEL/MFG./DATA LABEL: DO NOT REMOVE!
• DO NOT ALLOW CHILDREN UNDER SIX YEARS OF AGE TO USE THE UPPER BUNK.
• ALWAYS USE GUARDRAILS ON BOTH LONG SIDES OF THE UPPER BUNK.
• PROHIBIT HORSEPLAY ON OR UNDER BEDS.
• PROHIBIT MORE THAN ONE PERSON ON THE UPPER BUNK.
• USE THE LADDER FOR ENTERING OR LEAVING THE UPPER BUNK.
• If the bunk bed is placed next to a wall, the guardrail that runs the full length of the bed should be placed against the wall to prevent entrapment between the bed and the wall.
• Follow information on warnings appearing on the upper bunk end structure and on the carton.
• ALWAYS USE THE RECOMMENDED SIZE MATTRESS OR MATTRESS SUPPORT, OR BOTH, TO HELP PREVENT ENTRAPMENT OR FALLS.
• The surface of the mattress must be at least five inches (127mm) below the upper edge of the guardrails.
• Periodically check and ensure that the guardrail, ladder, and other components are in their proper position, free from damage, and that all connectors are tight.
• DO NOT USE SUBSTITUTE PARTS. Contact the manufacturer or dealer for replacement parts.
• The use of a night light may provide added safety for a child using the upper bunk.
• The use of water or sleep flotation mattresses is prohibited.
• STRANGULATION HAZARD: NEVER ATTACH OR HANG ITEMS TO ANY PART OF THE BUNK BED THAT ARE NOT DESIGNED FOR USE WITH THE BED; for example, hooks, belts, and jump ropes.
• PROHIBIT JUMPING ON BEDS.

Mattress Size Requirements:

• Twin Size Mattress: Width between 37-1/2" (952mm) and 38-1/2" (978mm); Length between 74" (1880mm) and 75" (1905mm).
• Full Size Mattress: Width between 53-1/2" (1359mm) and 54-1/2" (1384mm); Length between 74" (1880mm) and 75" (1905mm).
• The mattress must be no thicker than 7" (178mm).

Signature Design Furniture is not liable for damage or injury due to improper assembly or abusive use.

KEEP ALL INSTRUCTIONS INCLUDED WITH YOUR BEDROOM COMPONENTS FOR FUTURE REFERENCE.

Parts List

The following parts are included for assembly:

• A x 1
• B x 1
• C x 1
• D x 1
• E x 2
• F x 4
• G x 2
• H x 3
• J x 2
• K x 1
• L x 1
• M x 1
• N x 5
• P x 1
• R x 16 (1/4" x 85mm)
• S x 16 (1/4")
• T x 6 (1/4" x 30mm)
• U x 8
• W x 10
• Y x 52
• Z x 1
• AA x 6
• AB x 4
• AC x 44
• AD x 2 (Not Included / No Se Adjunto / Non Indus / 不提供此工具)

Assembly Steps

Step 1:

• Place part D on a flat surface.
• Attach parts H to part D using bolts R and washers S.
• Attach parts A and B to the assembled D/H structure using bolts Z and washers AC.
• Ensure all bolts are started but not tightened.

Step 2:

• Attach parts J to the sides of the assembled unit from Step 1 using bolts Z and washers AC.
• Attach parts K and L to the top of the unit using bolts Z and washers AC.
• Attach part E to the sides of the unit using bolts T and washers AC.

Step 3:

• Attach the bed slats (part F) to the side rails (part E) using bolts U and washers Y. Ensure slats are evenly spaced.

Step 4:

• Attach the ladder rails (part N) to the side rails (part E) using bolts Z and washers AC.
• Attach the ladder rungs (part P) to the ladder rails (part N) using bolts W and washers Y.

Step 5:

• Attach the second bunk bed frame (parts C and M) to the assembled lower bunk using bolts AB and washers Y.

Step 6:

• Attach the guardrails (parts G) to the upper bunk frame using bolts AA and washers AD.

Step 7:

• Attach the ladder (assembled in Step 4) to the upper bunk frame using bolts M7 x 80mm and M7 x 50mm.

Step 8:

• Attach the remaining bed slats (part F) to the upper bunk frame using bolts U and washers Y.

Step 9:

• Secure all remaining connections using the provided hardware.

Step 10:

• Final check of all bolts and connections to ensure they are tight.

Step 11:

• Note: Always disassemble the bed prior to moving to a new location.

Contact Information

For replacement parts or further assistance, please contact:

• Email: RTAParts@ashleyfurniture.com
• Website: www.ashleyfurniture.parts
• Phone: 1-844-966-0809