ErGear Dual Desk Monitor Arm

Compatibility Check

Before starting, ensure your monitor is compatible:

1. VESA Pattern: Does your monitor have a VESA pattern of 75x75mm (3"x3") or 100x100mm (3.9"x3.9")?
2. Weight Capacity: Does your monitor, including accessories, weigh less than 22 lbs (10 kg)?

If both answers are 'Yes', your monitor is compatible. If not, this mount is not suitable.

Tools Needed (Not Included)

Phillips Head Screwdriver, Electric Drill (for grommet mounting)

Important Notes & Cautions

• Read all instructions carefully before installation. Contact technical support or customer service if you have questions.
• Not all included hardware may be used.
• CAUTION: Do not use this product for purposes not specified in the manual. Do not exceed weight capacity. ErGear is not liable for damage or injury from improper use. Verify all parts are included and undamaged before assembly.
• WARNING: Contains small parts (choking hazard). Gas spring arms are under high pressure; do not puncture or expose to fire. Do not use on desks made of particle board or soft woods.

Product Features

The ErGear Desk Monitor Arm offers full articulation, allowing for tilt, swivel, and rotation adjustments for optimal viewing angles. It supports both C-Clamp and Grommet mounting options.

Mounting Options:

• C-Clamp Mounting: Suitable for desk thicknesses from 0.39" to 2.56" (10-65mm). Ensure the C-clamp makes full contact with the desk or a spacer.
• Grommet Mounting: Suitable for desk thicknesses from 0.39" to 2.17" (10-55mm). Requires a desk hole of 7/16"-7/8" (11-22mm) diameter. If no hole exists, drill one at least 2" (50mm) from the desk edge.

Installation Steps

1. Install the Base:
   • C-Clamp Mounting: Assemble the C-clamp components (06, 05, A, E) and attach to the desk edge. Use spacers if needed to ensure a secure fit.
   • Grommet Mounting: Insert the grommet bolt (C) into the base (03). Assemble the grommet mounting hardware (06a, B, E) and secure through the desk's grommet hole.
2. Attach Arm Sections:

   Connect the lower arm section [02] to the base and the upper arm section [01] to the lower arm section. Tighten set screws (D) without overtightening. Ensure cable covers face downwards.

3. Attach Monitor Plates:

   Select the appropriate bolts (M4 x 12mm or M4 x 30mm) and washers (M-C) for your monitor's VESA mounting holes. Use spacers (M-D) if necessary for curved monitor backs. Ensure bolts thread in at least 4-5 turns and do not bottom out.

4. Hang Monitors:

   Remove the knobs [S] from the monitor plate connectors. Hang the monitor onto the plate and secure by tightening the knobs [S]. Ensure the monitor is securely attached.

5. Adjust Gas Spring Tension:

   WARNING: Keep the arm in a horizontal position during adjustment. You may need assistance.

   Use the large Allen key (E) to adjust the gas spring tension. Turn counter-clockwise (+) to increase tension if the monitor falls, or clockwise (-) to decrease tension if the monitor rises. Adjust until the arm stays in the desired position.

6. Swivel Restriction:

   Adjust the swivel restriction as needed.

7. Tilt Adjustment:

   Grip the monitor edges to adjust the tilt angle. Do not press on the screen. If stiff, loosen the tilt-lock bolt [T] with the Allen key (E), adjust, and retighten.

   WARNING: Do not position or swivel the monitor beyond the edge of the desktop to prevent tipping.

8. Monitor Rotation:

   Rotate the monitor 360° as needed.

9. Route Cables:

   Securely route monitor and power cables along the arm using the provided cable management clips and covers (07).

Support & Contact

For assistance, please contact ErGear:

• US/CA: 1-800-651-9525 (Mon-Fri, 8am-8pm CST)
• UK: 44-808-196-3875 (Mon-Fri, 2pm-10pm UTC)
• Website: https://ergear.com
• Email: support@ergear.com
• JP Email: supportjp@ergear.com