ErGear Monitor Table Stand Instruction Manual

Unpacking Instructions and Important Safety Information

• Carefully open the carton, remove contents and lay out on cardboard or other protective surface to avoid damage.
• Check package contents against the Supplied Parts and Hardware List to assure that all components were received undamaged. Do not use damaged or defective parts.
• Not all parts and hardware included will be used. If you require replacement parts, contact customer service at support@ergear.com.
• Carefully read all instructions before attempting installation.
• If you do not understand the instructions or have any concerns or questions, please contact customer service at support@ergear.com.
• This product may contain moving parts. Use with caution.
• Do not use this product for any purpose or in any configuration not explicitly specified in this instruction. ErGear disclaims any liability for injury or damage arising from incorrect assembly, incorrect mounting, or incorrect use of this product.

Supplied Parts and Hardware

The following parts and hardware are included. Note that not all parts and hardware may be used in the assembly.

Step 1A: For C Clamp Mounting

1. STEP 1A-1: Install part [02] to pole [01]

   Attach the C-clamp mount [02] to the pole [01] using bolt [B] and washer [E].

2. STEP 1A-2: Adjust the mount according to the thickness of desktop

   Adjust the clamp to fit desktops with a thickness less than 45mm (1 49/64 in.) or between 45mm (1 49/64 in.) and 80mm (3 5/32 in.).

3. STEP 1A-3: Install part [03] to part [02]

   Install the grommet mount base [03] to the C-clamp mount [02] using bolt [A].

4. STEP 1A-4: Secure the mount to the desktop

   Secure the assembled mount to the desktop using the large knob [F].

Step 1B: For Grommet Mounting

1. STEP 1B-1: Remove part [a] from part [03]

   Remove the central screw or pin [a] from the grommet mount base [03].

2. STEP 1B-2: Secure the mount to desktop

   Insert the grommet mount base [03] through the desk grommet hole. Secure it from underneath using the base plate [08] and screw [a].

Step 2: Install Cable Clips [06] [07] & Monitor Connector [04] to Pole [01]

1. STEP 2-1: Slide the cable clip [06] and monitor connector [04] to the pole [01]

   Slide the cable clip [06] and the monitor connector [04] onto the pole [01].

2. STEP 2-2: Secure monitor connector [04] to the pole [01] then attach the cable clips [07] to the monitor connector [04]

   Secure the monitor connector [04] to the pole [01]. Then, attach the cable clips [07] to the monitor connector [04].

Step 3: Check Monitor Hole Pattern and Select Monitor Bolts

Verify your monitor's VESA mounting hole pattern. Common patterns are 75mm x 75mm (approx. 3 in. x 3 in.) and 100mm x 100mm (approx. 4 in. x 4 in.).

Select the appropriate bolts (M4 or M5) and length (M-A to M-D) based on your monitor's VESA mount depth. Ensure adequate thread engagement (at least 5 turns). Too short a bolt will not hold the monitor, and too long a bolt can damage the monitor.

Bolt Length Guide:

• Too Short: [❌]
• Too Long: [❌]
• Correct: [✔️]

Step 4: Attach the Monitor Plates [05] to the Monitors

For monitors with a flat back, use monitor plates [05] and attach them using bolts M-A/M-C and washer M-E.

For monitors with a round back, use monitor plates [05] and attach them using bolts M-B/M-D, washer M-E, and washer M-F.

Step 5: Hang Monitors to the Stand and Secure with Knob [C] and Bolts [D]

Hang the monitor plates [05] attached to the monitors onto the stand's arms. Secure each monitor using the knobs [C] and bolts [D].

Step 6: Fix Tilt Angle of the Monitors

Adjust the tilt angle of the monitors as desired. Use the provided Allen key [F] (15/64 in. or 6mm) to tighten the tilt adjustment mechanism.

Step 7: Manage Cables

Route monitor and power cables through the cable clips [06] and [07] attached to the pole and arms for a tidy setup.

Step 8: Store Allen Keys into the Cable Clip

Store the Allen keys [E] (5/32 in. or 4mm) and [F] (15/64 in. or 6mm) in the designated cable clip [06] for easy access.

Features

This monitor stand allows for individual VESA plate height adjustment, enabling perfect alignment of your monitors. It supports 360° rotation and tilt adjustments for optimal viewing angles.