RÅDMANSÖ 6-Drawer Dresser

Step 1: Attach Drawer Slides (CR)

Lay the side panel (marked CR) flat. Attach the drawer slide runner (CR, part 10115683) to the designated holes using 9x screws (10047245). Ensure the runner is oriented correctly as shown in the diagram.

Step 2: Attach Drawer Slides (CL)

Lay the other side panel (marked CL) flat. Attach the drawer slide runner (CL, part 10115683) to the designated holes using 9x screws (10047245). Ensure the runner is oriented correctly.

Step 3: Connect Side Panels to Base

Insert dowels into the base panel. Align the side panels (from steps 1 & 2) with the base panel and push them together. Secure the connection by inserting cam locks into the side panels and turning them to lock onto the dowels.

Step 4: Attach Drawer Slides to Top Panel

Take the top panel. Attach drawer slide runners (CR and CL) to the underside of the top panel using 9x screws (10047245) for each side, mirroring steps 1 and 2.

Step 5: Assemble Main Carcass

Connect the assembled side panels (from step 3) to the top panel (from step 4). Insert dowels and secure with cam locks as shown.

Step 6: Attach Back Panels

Slide the back panels into the grooves on the side and top/bottom panels. Ensure they are fully seated.

Step 7: Attach Legs

Turn the main carcass upside down. Attach the leg supports (10116141) to the bottom panel using 2x screws (10075558) for each support. Then, attach the legs (10095994) to the leg supports using 2x bolts (10051084) for each leg.

Step 8: Install Drawer Runners

Turn the unit upright. Install the drawer runners (150688) on the inside of the carcass using 8x cam locks (10093081) and cam dowels (10093082) as shown.

Step 9: Assemble Drawer Boxes

Assemble the drawer boxes. Connect the drawer sides to the drawer front and back panels. Secure with cam locks and dowels. Ensure the drawer bottom slides into the grooves.

Step 10: Attach Drawer Fronts

Attach the drawer fronts to the assembled drawer boxes. Use the connecting piece (100001) and large bolts (105251) to secure the drawer fronts to the drawer boxes.

Step 11: Attach Drawer Slides to Drawer Boxes

Attach the corresponding drawer slide components (CL/CR) to the sides of the assembled drawer boxes using 4x bolts (10003283) and the connecting piece (100001). Ensure correct orientation.

Step 12: Install Drawer Legs/Supports

Attach the leg assembly to the bottom of the main carcass. Use 4x bolts (10120564) and the connecting piece (100001).

Step 13: Attach Top Support Rail

Attach the top support rail to the top of the carcass. Use 4x bolts (10121698) and washers (10114605).

Step 14: Install Anti-Tip Device

Attach the anti-tip device brackets (150688) to the back of the dresser using 2x screws. This is part of the wall anchoring kit.

Step 15: Attach Drawer Front Support

Attach the drawer front support piece using 4x wooden dowels (101345).

Step 16: Insert Drawers

Carefully insert the assembled drawers into the dresser carcass, aligning them with the drawer slides.

Step 17: Install Drawer Bottom Supports

Install drawer bottom supports or rails as shown, using 4x screws (10075558) and 4x cam dowels (10051084).

Step 18: Final Adjustments

Use the wrench (190459) to make final adjustments to the legs or leveling feet if applicable.

Step 19: Attach Drawer Fronts (Detail)

Detail view showing how drawer fronts attach to the drawer boxes, likely with screws or clips.

Step 20: Insert Drawer

Insert the assembled drawer into the carcass. An arrow indicates the direction of insertion.

Step 21: Wall Mounting Instructions

Wall Mounting: The supplied screws and plugs can be used with most solid (A) and hollow (B) walls. For solid wood (C), use screws without plugs. If uncertain, seek professional advice.

Visit: www.IKEA.com/secure-it or www.IKEA.cn/secure-it

• Option A (Solid Wall): Drill hole (Ø 8 mm / 5/16"), insert plug, screw in screw.
• Option B (Hollow Wall): Drill hole (Ø 8 mm / 5/16"), insert plug, screw in screw.
• Option C (Solid Wood): Drill hole (Ø 3 mm / 1/8"), screw in screw directly.

Step 22: Secure to Wall

Attach the anti-tip device to the wall using appropriate hardware. The diagram shows a bracket being secured to the wall with screws (158469) and plugs (126916).

Step 23: Final Wall Attachment

Secure the dresser to the wall using the anti-tip device. The diagram shows a bracket (133304) being attached to the dresser and then to the wall.

Step 24: Drawer Assembly (Part 2)

Assemble drawer components. This step shows connecting drawer sides to the drawer base.

Step 25: Attach Drawer Back Panel

Attach the drawer back panel to the assembled drawer sides and bottom.

Step 26: Install Drawer Bottom Support

Install a support rail or piece at the bottom of the drawer assembly using part 10040242.

Step 27: Assemble Drawer Box Frame

Assemble the frame of the drawer box, connecting the sides and top/bottom panels.

Step 28: Attach Drawer Slides to Drawer Box

Attach the drawer slide components to the sides of the drawer box using 4x screws (159553) and brackets (117434).

Step 29: Attach Drawer Runners to Drawer Box

Attach the drawer runners (part 10115683) to the drawer box sides using screws (10047245). Labels DL and DR indicate left and right sides.

Step 30: Install Drawer Front Hardware

Attach the drawer front to the drawer box using a screw (119976) and a cap (10109447). A drill is shown with a cross mark, indicating not to use a power drill for this specific step. ❌⚡

Step 31: Final Drawer Insertion and Safety Check

Insert the assembled drawer into the dresser. The diagram includes a safety warning icon indicating potential tip-over risk if not properly secured to the wall. ⚠️