HAUGA 6-Drawer Dresser Assembly Instructions

Important Safety Information

⚠️ WARNING: Children have died from furniture tipover. To reduce the risk of furniture tipover:

• ALWAYS install the anti-tip device provided.
• NEVER put a TV on this product.
• NEVER allow children to stand, climb, or hang on any drawers, doors, or shelves.
• NEVER open more than one drawer at a time.
• DO NOT defeat or remove the drawer interlock system; it is an important stability and safety system.
• Place heaviest items in the lowest drawers.

Tools Required for Assembly:

• Screwdriver (Phillips head)
• Hammer
• Drill with drill bits: 5/16" (8 mm) and 1/8" (3 mm)

Wall Mounting Considerations:

The supplied screws and plugs can be used with most solid (A) and hollow (B) walls. For solid wood (C), use screws without plugs. If uncertain, seek professional advice.

Diagram A shows drilling into a solid wall with a 5/16" (8 mm) drill bit and using a plug.

Diagram B shows drilling into a hollow wall with a 5/16" (8 mm) drill bit and using a plug.

Diagram C shows drilling into solid wood with a 1/8" (3 mm) drill bit and using a screw directly.

Parts List

The following parts are used throughout the assembly. Quantities are indicated in the steps.

Hardware:

Furniture Components:

Various wooden panels for the dresser frame, drawer sides, drawer bottoms, back panels, and top panel.

Assembly Steps

Step 1: Prepare Base and Sides

Attach two base runners (Part 10051022) to the main base panel (Part 10051022) using 14x dowels (Part 101345) and 10x screws (Part 151706).

Diagram shows two base runners being attached to a larger panel with dowels and screws.

Step 2: Attach Drawer Slides (Left)

Attach 6x drawer slide components (Part 10093081 - IKEA CL) to the prepared base assembly using 9x screws (Part 146114).

Diagram shows attaching drawer slides to the base assembly using screws.

Step 3: Attach Drawer Slides (Right)

Attach 6x drawer slide components (Part 10085235 - IKEA CR) to the prepared base assembly using 9x screws (Part 146114).

Diagram shows attaching drawer slides to the base assembly using screws.

Step 4: Assemble Frame Sides

Connect two side panels to the base assembly using 2x dowels (Part 153548) and 2x screws (Part 10040039). A "Click!" sound is indicated.

Diagram shows connecting side panels to the base with dowels and screws, with a "Click!" sound effect indicated.

Step 5: Assemble Frame Sides (Continued)

Connect two more side panels to the base assembly using 4x dowels (Part 158568) and 4x screws (Part 10051022). A "Click!" sound is indicated.

Diagram shows connecting more side panels to the base assembly with dowels and screws, with a "Click!" sound effect indicated.

Step 6: Attach Back Support

Attach a back support panel using 4x dowels (Part 153548) and 4x screws (Part 10040039). A "Click!" sound is indicated.

Diagram shows attaching a back support panel using dowels and screws, with a "Click!" sound effect indicated.

Step 7: Attach Back Support (Continued)

Attach another back support panel using 4x dowels (Part 158568) and 4x screws (Part 10051022). A "Click!" sound is indicated.

Diagram shows attaching another back support panel using dowels and screws, with a "Click!" sound effect indicated.

Step 8: Insert Back Panel

Slide the back panel into the grooves of the assembled frame.

Diagram shows sliding a thin panel into the back of the dresser frame.

Step 9: Secure Back Panel

Secure the back panel using 8x screws (Part 151706) and 8x screws (Part 151708).

Diagram shows screwing the back panel into place.

Step 10: Secure Back Panel (Continued)

Secure the back panel further using 8x screws (Part 151705) and 8x screws (Part 151707).

Diagram shows screwing the back panel into place.

Step 11: Attach Drawer Runners

Attach 6x drawer runner components (Part 10093081 and 10093082) to the inside of the dresser frame using screws.

Diagram shows attaching drawer runners to the side panels of the dresser frame.

Step 12: Attach Drawer Slides to Drawer Sides

Attach 8x drawer slide components (Part 101345) to the drawer side panels.

Diagram shows attaching drawer slides to the sides of drawer boxes.

Step 13: Attach Drawer Slides to Drawer Sides (Continued)

Attach 8x drawer slide components (Part 101345) to the other drawer side panels.

Diagram shows attaching drawer slides to the sides of drawer boxes.

Step 14: Attach Drawer Fronts

Attach drawer fronts using 4x dowels (Part 153548) and 2x screws (Part 10040039) for the handles, and 2x screws (Part 158568) for the drawer front attachment.

Diagram shows attaching drawer fronts with handles and screws.

Step 15: Attach Top Panel

Place the top panel onto the assembled frame and secure it using 4x screws (Part 101345).

Diagram shows placing and securing the top panel.

Step 16: Attach Drawer Fronts (Handles)

Attach drawer handles using 2x screws (Part 151706) and 2x screws (Part 151708) for the left side, and 2x screws (Part 151705) and 2x screws (Part 151707) for the right side.

Diagram shows attaching drawer handles with screws.

Step 17: Install Drawer Slides

Insert the drawer slide mechanisms into the dresser frame. This involves aligning and clicking them into place.

Diagram shows inserting drawer slide mechanisms into the dresser frame, with arrows indicating movement and a "click" sound.

Step 18: Wall Mounting Preparation

Mark the wall for mounting points.

Diagram shows marking points on a wall.

Step 19: Wall Mounting Guidance

Details on using screws and plugs for different wall types (solid, hollow, wood). Refer to the safety section for details.

Diagrams illustrate wall mounting with screws and plugs for different wall types.

Step 20: Attach Anti-Tip Device

Attach the anti-tip bracket to the dresser using 2x screws (Part 109048).

Diagram shows attaching an anti-tip bracket to the dresser with screws.

Step 21: Attach Anti-Tip Device to Wall

Attach the corresponding anti-tip bracket to the wall using screws and plugs (refer to Step 19). Then connect the dresser to the wall bracket to secure it.

Diagram shows attaching wall brackets and connecting them to the dresser.

Step 22: Secure Anti-Tip Device

Secure the anti-tip device by tightening screws.

Diagram shows tightening screws for the anti-tip device.

Step 23: Assemble Drawer Boxes

Assemble drawer boxes using 2x dowels (Part 118331) and 2x screws (Part 118331) for the first drawer, and 4x dowels (Part 118331) and 4x screws (Part 118331) for the second drawer.

Diagram shows assembling drawer boxes with dowels and screws.

Step 24: Assemble Drawer Sides

Assemble drawer sides using 2x dowels (Part 101345) and 2x screws (Part 101345) for one set of drawer sides, and 8x dowels (Part 101345) and 8x screws (Part 101345) for another set.

Diagram shows assembling drawer sides with dowels and screws.

Step 25: Attach Drawer Sides to Base

Attach the assembled drawer sides to the drawer base panels.

Diagram shows attaching drawer sides to drawer bases.

Step 26: Attach Drawer Backs

Attach drawer backs using 4x screws (Part 111911802230200476) and 4x screws (Part 10040242).

Diagram shows attaching drawer backs with screws.

Step 27: Insert Drawer Bottoms

Slide the drawer bottom panels into the grooves of the assembled drawer sides and back.

Diagram shows sliding drawer bottom panels into place.

Step 28: Secure Drawer Fronts

Attach drawer fronts to the assembled drawer boxes.

Diagram shows attaching drawer fronts to drawer boxes.

Step 29: Attach Drawer Handles

Attach drawer handles to the drawer fronts.

Diagram shows attaching drawer handles.

Step 30: Attach Drawer Runners to Drawers

Attach the drawer runner components to the sides of the assembled drawers using 4x screws (Part 151495575138).

Diagram shows attaching drawer runners to the sides of the drawer boxes.

Step 31: Attach Drawer Runners to Drawers (Continued)

Attach more drawer runner components to the sides of the assembled drawers using 4x screws (Part 119030), 4x screws (Part 118224), and 4x screws (Part 120076).

Diagram shows attaching drawer runners to the sides of the drawer boxes.

Step 32: Insert Drawers

Insert the assembled drawers into the dresser frame by aligning the runners. This involves attaching drawer runners (Part 10102070) to the dresser frame (IKEA DL) and drawer sides (IKEA DR) using 2x screws (Part 109048) and 6x screws (Part 146114).

Diagram shows inserting drawers into the dresser, aligning runners.

Step 33: Attach Drawer Knobs

Attach drawer knobs to the drawer fronts using 2x screws (Part 119976) and 2x screws (Part 10052019).

Diagram shows attaching drawer knobs to the drawer fronts.

Step 34: Final Check and Drawer Insertion

Ensure all parts are securely fastened. Insert the drawers into the dresser. A warning symbol indicates not to place items on top of open drawers.

Diagram shows inserting drawers into the dresser and a warning about not placing items on top of open drawers.

Step 35: Completed Dresser

The HAUGA 6-drawer dresser is now assembled and ready for use.

Diagram shows the fully assembled HAUGA 6-drawer dresser with drawers open.

Wall Mounting Instructions

Step 1: Position the dresser against the wall. Mark the wall through the mounting holes on the dresser's back panel.

Diagram shows marking the wall through holes in the dresser.

Step 2: Secure the anti-tip bracket to the wall using appropriate screws and wall anchors based on your wall type (refer to safety section). Ensure the bracket is firmly attached.

Diagram shows attaching a bracket to the wall with screws and anchors.

Step 3: Attach the other part of the anti-tip device to the dresser. Then, connect the dresser to the wall bracket to secure it.

Diagram shows connecting the dresser to the wall bracket.