RÅDMANSÖ Chest of 5 Drawers Assembly Instructions

Safety Warnings

⚠️ WARNING: Serious or fatal crushing injuries can occur from furniture tip-over.

ALWAYS secure this furniture to the wall using tip-over restraints.

To further reduce the risk of serious injury and death from tip-overs:

• Place heaviest items in the lower drawer.
• Never let children climb or hang on drawers, doors, or shelves.

? Do not allow children to climb or hang on the furniture.

The multilingual warnings in the original document emphasize these points across various languages.

Tools and Hardware

Tools Required:

• Cross-head screwdriver
• Flat-head screwdriver
• Pencil
• Hammer
• Drill (for wall mounting)
• Measuring tape
• Spirit level (recommended for wall mounting)

Hardware Included (Refer to diagrams for specific quantities per step):

• Dowels: 4x (part 118740), 4x (part 101345)
• Screws: 30x (part 10047245), 5x (part 119976), 5x (part 10109447), 2x (part 109572), 4x (part 151931), 4x (part 10003283), 4x (part 10120564), 4x (part 10121698), 8x (part 105251), 30x (part 10047245), 5x (part 10040242), 2x (part 10087223), 4x (part 10075382)
• Brackets/Connectors: 2x (part 10047244), 1x (part 190459), 20x (part 117434), 2x (part 158701), 2x (part 126916), 2x (part 10087223), 4x (part 10075382)
• Drawer Runners: CL, CR (5 pairs total)
• Feet/Levelling elements: 2x (part 10095994), 2x (part 10114407), 2x (part 10114605)
• Other: 1x (part 100001), 4x (part 101345), 20x (part 159553)

Assembly Steps

Step 1: Attach Drawer Runners to Side Panels

Take two side panels. Attach drawer runners labeled 'CL' and 'CR' to the inside faces of these panels using screws (part 10047245). Ensure the runners are oriented correctly as shown in the diagram.

Step 2: Insert Dowels into Base and Top Panels

Insert dowels (part 101345) into the pre-drilled holes on the edges of the base and top panels.

Step 3: Assemble Main Cabinet Frame

Connect the side panels to the base and top panels. Use brackets (part 10047244) and screws (part 10040242) to secure the connections. Ensure the frame is square.

Step 4: Attach Wall Mounting Bracket

Attach the wall mounting bracket (part 158701) to the back of the cabinet frame using screws (part 151931).

Step 5: Attach Back Panel

Slide the back panel into the grooves on the side and top/base panels. Ensure it is fully seated. Use screws (part 109572) and brackets (part 126916) to secure it.

Step 6: Attach Second Side Panel

Attach the remaining side panel to the assembled frame.

Step 7: Insert Dowels

Insert dowels (part 118740) into the designated holes on the top panel.

Step 8: Attach Top Panel

Place the top panel onto the assembled frame, aligning the dowels with the holes.

Step 9: Secure Top Panel

Secure the top panel from the inside using screws (part 105251) and the tool (part 100001).

Step 10: Prepare Drawer Front/Back Panels

Insert dowels (part 118740) into the designated holes on the drawer front and back panels.

Step 11: Slide Drawer Base Panels

Slide the drawer base panels into the grooves of the drawer sides.

Step 12: Assemble Drawer Box

Attach the drawer front and back panels to the drawer sides using screws (part 105251).

Step 13: Assemble Base Frame with Legs

Assemble the base frame by connecting the horizontal supports and legs. Use screws (part 10003283) and the tool (part 100001).

Step 14: Attach Base Frame to Cabinet

Attach the assembled base frame to the bottom of the main cabinet body using screws (part 10114407).

Step 15: Attach Feet/Levelling Elements

Attach the feet or levelling elements (parts 10114605, 10121698) to the legs of the base frame.

Step 16: Attach Internal Shelf Supports

Attach the internal shelf supports (part 10075382) to the inside of the cabinet.

Step 17: Place Top Shelf

Place the top shelf into the cabinet, resting on the supports.

Step 18: Check for Levelness

Use a spirit level (recommended) to ensure the cabinet is level. Adjust feet if necessary.

Step 19: Attach Rear Cabinet Panel

Attach the rear panel of the cabinet structure using screws (part 105251) and tool (part 100001).

Step 20: Insert Drawers

Slide the assembled drawers into the cabinet runners.

Drawer Assembly (Detailed Steps 23-29)

Follow the diagrams to assemble each drawer. This typically involves connecting drawer sides, front, back, and base panels using screws and dowels.

Step 23: Assemble Drawer Sides and Base

Connect the drawer sides and base panel.

Step 24: Attach Drawer Front

Attach the drawer front panel.

Step 25: Attach Drawer Runners to Cabinet Interior

Attach the drawer runners to the inside of the cabinet structure.

Step 26: Attach Drawer Runners to Drawer Sides

Attach the drawer runners to the sides of the assembled drawer.

Step 27: Attach Drawer Front to Drawer Sides

Secure the drawer front to the drawer sides.

Step 28: Attach Drawer Runners to Drawer Sides

Attach the drawer runners to the sides of the drawer.

Step 29: Attach Drawer Front to Drawer Sides

Secure the drawer front to the drawer sides.

Step 30: Final Product and Usage

Ensure all drawers are properly inserted and function smoothly. The diagram shows the final assembled chest of drawers with drawers open, indicating a final check or usage. A warning icon (⚠️) and prohibition icon (?) are present, likely indicating not to overload or allow children to climb.

Wall Mounting Instructions

Important: For your safety, this furniture MUST be secured to the wall with the provided tip-over restraint(s).

The supplied screws and plugs are suitable for most solid (A) and hollow (B) walls. For solid wood (C) walls, use the screws without plugs.

Wall Type A (Solid Walls):

• Drill holes using a Ø 8 mm (5/16") drill bit.
• Insert the provided plugs (part 10087223).
• Secure the bracket (part 158701) using the provided screws (part 151931, approx. 70 mm length).

Wall Type B (Hollow Walls):

• Drill holes using a Ø 8 mm (5/16") drill bit.
• Insert the provided plugs (part 10087223).
• Secure the bracket (part 158701) using the provided screws (part 151931, approx. 30 mm length).

Wall Type C (Solid Wood):

• Use screws (Ø 3 mm (1/8")) directly into the solid wood without plugs.

If you are uncertain about the correct type of wall or fixings, seek professional advice.