RÅDMANSÖ Chest of Drawers

Safety Information

⚠️ WARNING: Furniture tip-over can cause serious or fatal crushing injuries.

ALWAYS secure this furniture to the wall using the provided tip-over restraints.

To further reduce the risk of serious injury and death from tip-overs:

• Place heaviest items in the lower drawers.
• Never let children climb or hang on drawers, doors, or shelves.

Wall Mounting Guide:

The supplied screws and plugs can be used with most solid (A) and hollow (B) walls. For solid wood (C), use the screws without plugs. If you are uncertain, seek professional advice.

• Type A & B (Solid/Hollow Walls): Drill an Ø 8 mm (5/16") hole. Insert plug. Use screw.
• Type C (Solid Wood): Drill an Ø 3 mm (1/8") hole. Use screw without plug.

Assembly Steps

This guide provides step-by-step instructions for assembling the RÅDMANSÖ chest of drawers. Please identify all parts before starting.

Tools Required:

• Phillips head screwdriver
• Flathead screwdriver
• Hammer
• Drill
• Drill bits (Ø 8 mm / 5/16", Ø 3 mm / 1/8")

Parts Overview:

Refer to the diagrams for specific part identification and quantities.

Group 1 Hardware:

• 4x Metal rods (Part ID: 118740)
• 4x Wooden dowels (Part ID: 101345)
• 8x Spring screws (Part ID: 105251)
• 1x Allen key (Part ID: 100001)
• 4x Screws (Part ID: 10120564)
• 4x Screws (Part ID: 10003283)
• 4x Screws (Part ID: 10121698)
• 4x Caps/washers (Part ID: 10114605)
• 2x Metal brackets (Part ID: 10115683)
• 30x Small screws (Part ID: 10047245)
• 1x Wrench (Part ID: 190459)

Group 2 Hardware & Components:

• 20x Drawer runners (CL - Left, CR - Right)
• 5x Drawer slides (Part ID: 10109447)
• 5x Screws (Part ID: 119976)
• 20x Drawer runners (additional)
• 30x Small screws (Part ID: 10040242)

Assembly Instructions:

Step 1: Attach drawer runners (CL and CR) to the inner sides of the main unit's side panels using small screws (10047245). Ensure correct orientation as per diagram.

Step 2: Connect the base panel to the side panels using wooden dowels (101345) and small screws (10047245).

Step 3: Attach a curved metal bracket (10115683) to the top edge of one side panel using screws (10047244). Ensure it is not attached upside down (indicated by a crossed-out diagram).

Step 4: Attach a wall mounting bracket (158701) to the top rear edge of the unit using screws (151931) and washers (10040242).

Step 5: Slide the back panel into the grooves on the side panels. The diagram shows a hand pushing the panel downwards.

Step 6: Attach the second side panel to the partially assembled unit, aligning it with the back panel and base.

Step 7: Attach the top panel to the side panels using wooden dowels (118740) and small screws (10047245).

Step 8: Secure the top panel by inserting spring screws (105251) into the pre-drilled holes. A hand symbol indicates tightening.

Step 9: Attach another bracket (100001) to the top of the unit using spring screws (105251) and washers (10003283).

Step 10: Assemble drawer bases. Connect drawer side panels to drawer base panels using wooden dowels (118740).

Step 11: Insert drawer slides (10114605) into the main unit frame. The diagram shows the slides being pushed into place until they click.

Step 12: Assemble the leg structure. Insert metal rods (118740) into the base and secure with screws (10003283).

Step 13: Attach the leg support structure to the base of the unit using screws (100001) and washers (10120564).

Step 14: Attach the leg support structure to the side panels of the main unit using screws (10120564).

Step 15: Secure the leg assembly to the main unit using specialized connectors (10114605, 10121698).

Step 16: Attach the top shelf support to the inside of the unit using screws (10075382).

Step 17: Place the top shelf onto the supports.

Step 18: Tighten the leg assembly using the provided wrench.

Step 19: Attach drawer runners (DR) to the assembled drawer boxes using screws (10115683) and washers (10047245). Also attach the corresponding drawer slides (DL).

Step 20: Final placement of the assembled unit.

Step 21: (Diagram shows the completed unit). No specific action required.

Step 22: Attach drawer slides (e.g., 109572) to the sides of the drawer boxes using screws (126916).

Step 23: Assemble drawer boxes. Connect drawer sides to drawer fronts using dowels and screws. A "Click!" sound indicates proper engagement.

Step 24: Attach drawer back panels.

Step 25: Attach drawer bottoms. The diagram shows sliding the bottom panel into grooves and securing it.

Step 26: Secure the drawer sides to the drawer front and back panels.

Step 27: Attach drawer runners to the main unit frame using screws (159553).

Step 28: Attach drawer slides (DR) to the assembled drawers.

Step 29: Final attachment of drawer slides (DL) to the drawer boxes.

Step 30: Insert the assembled drawers into the unit. Includes a safety warning symbol (⚠️).