Smart Camera User Manual

Introduction

Thank you for using the Smart Camera. This manual provides instructions for setup, operation, and maintenance.

Basic Parameters

• Product Name: Smart Camera
• Pixel: 3.0MP/4.0MP/5.0MP/8.0MP
• Video Compression: H.264, H.265 High Profile
• Image Enhancement: Digital Wide Dynamic, 3D Noise Reduction
• Local Storage: MicroTF card (8-128GB recommended for full functionality)
• Wireless Encryption: WEP/WPA/WPA2
• AC Input: 100-240V
• Total Power Consumption: 5W (Max)
• Wireless Standard: 2.4G 802.11 b/g/n
• Support Platform: Android/iOS

Component Description

Reset Button: Long press the reset button in the designated hole for 5 seconds to reset the device.

Installation and Setup

Install APP

Download the 'Smart Life' APP from your device's app store. Register and log in to your account.

Add Device - Scan QR Code Mode

1. Ensure your Wi-Fi is available and connected to the internet.
2. Connect the camera to power. Wait for system startup to complete.
3. Open the 'Smart Life' APP. Tap the '+' icon in the upper right corner of the main screen.
4. Select 'Security & Video Surveillance', then tap 'Smart Camera'.
5. Tap 'Next step'.
6. A QR code will be displayed on your mobile device. Position the camera approximately 20-30 cm from the mobile phone lens to scan the QR code.
7. Tap 'hear the prompt sound' on the APP.
8. The APP will show 'connecting'.
9. Once the connection is complete, tap 'Done'.
10. The preview interface will appear. After closing the preview, the device will be listed on the APP's home page for future access.

Add Device - WIFI Fast Connection Mode

1. Select 'EZ Mode'.
2. Tap 'Next'.
3. Enter your Wi-Fi account and password.
4. Tap to complete the connection.
5. The video screen will appear.

Matters Need Attention

• Keep the device away from metal spaces.
• Avoid placing the device near furniture or microwave ovens that may cause blockage.
• Keep the device away from audio, video, and data lines.
• Ensure the device is within the coverage of your Wi-Fi signal.
• If switching to a new network environment, press the reset button for approximately 5 seconds to reconnect.

Harmful Substances Information

This product conforms to RoHS environmental protection requirements. The table below indicates the presence of certain substances:

Note: Pb indicates Lead, Hg indicates Mercury, Cd indicates Cadmium, Cr(VI) indicates Hexavalent Chromium, PBB indicates Polybrominated Biphenyls, PBDE indicates Polybrominated Diphenyl Ethers. '○' indicates that the content of the substance is below the limit requirement, and 'X' indicates that the content of the substance is above the limit requirement.

This form is based on the provisions of SJ/T 11364. It is noted that there is currently no mature technology globally to replace or reduce the lead content in electronic ceramics, porcelain, optical glass, steel, and copper alloys.

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.

ISED Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device.

This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.

French Translation: Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Cet équipement doit être installé et utilisé avec une distance minimale de 20 cm entre le radiateur et votre corps.

Maintenance Records

Please fill out the following sections for maintenance:

• Maintenance time: ______
• Fault conditions: ______
• Fault cause: ______
• Troubleshooting: ______
• Return and exchange proof: ______
• Date of validity: ______
• Original device ID: ______
• New device ID: ______
• Maintenance personnel signature: ______
• Maintenance Department seal: ______

Maintenance Voucher of Intelligent

Customer: ______
Address: ______
Model: Smart Camera
Device store: ______
Store address: ______
Store contact number: ______
Mobile: ______
Camera ID: ______
Date of purchase: ______